开云体育

There's a caveat about cutting phenolic - beware. Don't cut it cold, it wIll crack. How I do it is warm it in a low oven, then cut it on a machine shear in one stroke.

Okay thanks. Looks I was being too restrictive on speaker options - this opens it up to a wide selection. And interesting concept on cutting off the end of the board.. I’m reading this as you cut

Sources changed many times over the Speak2Me project. Since I haven't built any for a while, I have no immediate knowledge of what is available today. We did notice a few things that can be useful-

just checking again -? can you recommend a source for the speaker?? I am not having much luck finding a suitable fit for the speak2me mod on LENi.????? thanks

Up and running. I ended up putting the resistor at the BNC connector and shrink wrapping the crud out of that end for strain relief purposes. Then I pigtail loop under and around to the LND terminal

Thank you.. that is what I thought, just wanted to make sure. Sent: Friday, May 15, 2020 5:27 PM To: [email protected] Subject: Re: [GEOelectronics] GEO 210 Probe budget kit 1 resistor. The

1 resistor. The other is spare, both same 3.3 Meg Ohms.Goes in series with center pin from BNC to the clip. Ludlum solders the resistor right to the clip, then the wire to the other end of the

sorry if you have already answered this..? the GEO 210 probe kit included two resistors.? Not sure the value, they appear the same. a) I assume I only need one of them. b) where does the one

Replaced LENi transformer, seems to have resolved everything.? I like the HV Meter - easy to use.

hi, thought I'd post here too.. just in case any thoughts. The geo HV meter works perfect on my Vic 6b, Ludlum 3, Bicron 200.?? So I know the box is good. When I put the HV Meter on my LENi, it

yes the probe sits sort of sideways. To: "GEOelectronics" <[email protected]> Sent: Friday, May 8, 2020 8:49:42 PM Subject: [GEOelectronics] GEO 210 Probe budget kit hi.. got the probe kit. Do

yes that should be there, can you show mea picture of the parts you found so far? George To: "GEOelectronics" <[email protected]> Sent: Friday, May 8, 2020 8:49:42 PM Subject: [GEOelectronics]

hi.. got the probe kit.? Do you have a clip to attach the red wire to the round connection on a LND 7311 sensor??? all I got was the red wire, couple of resistors, shrink wrap ... as for

makes more sense now.??? By the way, where do you get the speaker and mounting kit?? seems to be unobtainium.?? The volume knob/potentiometer seems it would be fairly routine.

keep reading to the bottom To: [email protected] Sent: Wednesday, May 6, 2020 11:53:02 AM Subject: Re: [GEOelectronics] SPEAK2ME So it looks like these instructions were for a build it yourself

So it looks like these instructions were for a build it yourself kit.. it’s the same as the already assembled speak2me board/module that you sell, correct? The already assembled module you sell

Ok, thanks!! Sent: Wednesday, May 06, 2020 9:47 AM To: [email protected] Subject: Re: [GEOelectronics] SPEAK2ME Yes thanks for asking and you may post this to CDV700Club and also LENin Group

Yes thanks for asking and you may post this to CDV700Club and also LENin Group [ https://www.qsl.net/k0ff/0_GEOelectronics_KITS_User_Manuals/ |

hi,? do you have instructions for the speak2me module??? what to hook up where, pinouts, what it does, etc. -MTC

Just kicking this new page off, if you have questions about anything you've bought or use from GEOelectronics, this is the place to ask for information. Much information has been stored at this link: