开云体育

His best bet is to call Yeasu’s tech support. Best Regards Hanford R Wright WA4LZC CCA# AC11-12590 Sent from my iPhoney please pardon my typos.

A friend has problem with his FT857. When he transmits in CW mode, it outputs just about 40 W. In other modes it can go to full 100 W. He tried reset and it did not help. Any hints? -- 73, YT9TP,

The link goes to a power cord but congrats on a loaded '857!! Got filters? ;] Tracy N4LGH

Purchased this radio just a month ago. https://www.ebay.co.uk/itm/263843884996 73 Mike M0SAZ

K6XX is using CAT through the mic jack. Do I need to worry about any transistors? I think he did this to isolate the lines. http://www.k6xx.com/radio/ft857ser.pdf

Greetings Tom, Quick question, what equipment did you use to sniff the data lines? I saw a reference to 64 kb/s which isn't standard. If I did the math right, I ended up with 5818 baud (11

Getting ready to back up the '857, do you have instructions you trust to back up the rig settings? Memory settings are of little importance to me, but those critical rig settings are and I've never

Thanks, Tom, I may well take you up on your offer! So far your info is all I have found on this except Tobias' tweet from a couple of years ago. How far has anyone else gone with this? YOU rock

Hi Tracy, that sounds like an interesting project! A Arduino front panel would be great. Feel free to update the protocol documentation if you find something missing or incorrect:

This tweet got my attention - https://twitter.com/DH1TW/status/716725492540436480 https://twitter.com/DH1TW/status/716725492540436480 OE9TKH's QRZ page https://www.qrz.com/db/OE9TKH/

Presumably the ITU Regions, perhaps reflecting any changes the IARU might make you these? Bob

I noticed in the service menu there is a setting for country (regions). Does someone know what valid regions are and what the impact on frequencies and other parameters are. The reason for asking. I

From: "John P Liddell jplidd@... [FT-857]" Some years ago I wrote a technical note which described, step-by-step, how to make the 857/897 operate on Winlink. It should still be in the "Files"

@Philip, It's not the fan noise she hears, it's because I turn up the volume to hear the RX, she can't hear her soaps :) I do have a separation kit but my shack is in the (small) spare bedroom so I'd

OM, My 857 is from the first "D" lot (ancient), but the fan is not noisy enough to annoy a bystander (XYL, et al). Is your noise a rushing sound associated with rapid air movement or possibly a

The settings I use for data for my FT857 are here: FT857 settings for digital modes <cid:part1.777C8521.A1D81F24@...> http://w7hd.ddns.net/fldigi/ft857-menu-settings-digital-operation.pdf

Hi Gareth, I’ve been wrestling with the same issue. I have been trying to use Winlink with my 857D but find confusion with the radio settings. Terms in the instructions like packet vs digital

Hi ya to all?I am looking at using my ft857d for data modes and I have bought a small data module from Radioarena.?Any one with help for me re how to set up as the instructions are a little

I agree with separation if necessary. I don’t mind my fan because it is doing its job. I have a Kenwood TM-281A 2 meter radio that I use mobile. It has no fan and after 20 minutes of rag chewing it

Yes, it is a nosy and powerful fan.? Considering the size (small) of the the sink, you need to be able to blow as much air across that heat sink as possible.? The best thing to do is get the