开云体育

Yes it will work but remember to change menu 59 back if your running the remote mike so the up/down buttons will work correctly. ____________________________________________________________

I have never seen one.?James B Stafford

Anybody ever tried to modify / adjust the SWR display to read from 0 to 2 instead from 0 to 3 ? Anything above 2 is really not that useful for quick antenna check AKA Field Day. I am not asking to get

Thank you all for the replies. 73 Les / W3LES

Hi, I have a question about using digital and voice modes from computer. I would like to know if there is anyone who did this modding in order to operate the radio from computer:

Hello Brad, sorry, I don't know why you mention "T"... I only had a problem with "I" shown on 2m band frequencies and as you know, this function should not be available on UHF and VHF... It turns out,

Sent: Thursday, June 28, 2018 at 10:41 PM From: "n4mf_sc@... [FT-857]" To: FT-857@... Subject: [FT-857] Re: FT857D ALC Hi Peter, If you can reprogram the radio easily I would try a

Sent: Friday, June 29, 2018 at 11:00 AM From: "'Lester Morrow / W3LES' lesterf52@... [FT-857]" To: FT-857@... Subject: [FT-857] Re: FT857D ALC Hi All, just got the 857d ...Dumb

Sent: Saturday, June 30, 2018 at 12:21 AM From: "g0ery@... [FT-857]" To: FT-857@... Subject: [FT-857] Re: FT857D ALC Good luck but I don't think a reset will fix it. The ALC on mine

Good luck but I don't think a reset will fix it. The ALC on mine behaved the same way. it was also more aggressive than some other radios (e.g. the 950) with a slow recovery time resulting in lower

Congratulations....Page 119 of the 857D Operating Manual covers THREE types of Power -on 'Factory Reset' procedures 1. Press and hold the [V/M} plus power. This resets All Memories AND following Menu

Hi All, just got the 857d ...Dumb Question How do you do a Factory reset?? Thanks Les/W3LES

Hi Peter, If you can reprogram the radio easily I would try a factory reset and then see what you get. There is also the possibility some of the parts values in the PA have changed and the service

Hi I have the problem that my 857D only shows ALC movement on 6 and 2M at up to the mid power level after this it declines until at full power there is no movement ? Any help would be most welcome,

Hi James, thank you very much for your answer! Yes, I think this issue is quite seldom... but in the meanwhile I saw a picture in the internet, where another guy had the "I"-character on a 70 cm

From: "uwe.dl4ac@... [FT-857]" snip I haven't seen this issue in my 12 (or whetever) years on this list nor on my own 857D so I suspect it's a software bug but whether the pre-amp actually is on

The T is Split Tone On. turn tone off. Page 31 of your manual. The IPO is Intercept Point Optimization. turns pre-amplifier on/off but not used on the 144 or 430 band. Page 43 of your manual

Hello Bill, yes, you are right: if IPO is set to on, the pre-amplifier is switched off and vice versa. But that is not my problem. During "normal" operation, the litte "I"-character should never

When the IPO is “on”, it’s really off and when it’s off, it’s “on”. Only YAESU can do this. Bill Albert AD5TD Woodsboro TX Sent from parchment and quill pen

Hello, I just got a FT-857D and I like it very much. But I recognized a strange thing: suddenly, after setting up some memories, the display shows for all 2m-frequencies the "I", which means, that