开云体育

Hi Marty, I'm not familiar with the MacBook Pro. I'm sorry to say I cannot suggest what to do with your timing issues. Tom, N8EUI [email protected]> wrote:

Tom, I am using have been using the onboard time source in the MacBook Pro. I have used it for years with my FT-1000MP and the older WSJTx software (V 2.3 and previous) just fine. I have restarted

As far as no messages showing in the Band Activity window, do you have your computer time synced with the WSJT-X software? Timing is everything with regards to making WSJT-X decode contacts. The two

Thanks for the info Tom. I have my radio tab set up much like yours. According to the 920 manual, the serial port parameters should be set to 4800, no parity (no provision to set parity on my setup),

I have a '920 and a Signalink USB configured for WSJT-X. Attached are photos and PDFs explaining how I have it set for on my PC. I hope this works for you. If you have any questions, feel free to

I have been trying to get my FT-920 to operate with WSJTx. ?I am using a SignaLink USB soundcard and a MacBook Pro computer. ?I have searched the web for set-up instructions and have been

Hey friends, i have a FT-920 which has some strange problems. When turning on the TRX with 13.8V supply, it makes strange noises and you can't hear any signal/noise. If i'm lowering the voltage to

Thats the way i measured it - with an storage scope. Currently, i have no idea about the duration of the spikes - but it was enough to kill an Amp of a friend. I can measure them again, but first i

Sebastian, Thank you for reply.? That is good to know information.? Could you tell me what you used to capture the spike.? I have assumed it would be too fast to record without a storage scope.?

Hey Wes, i have 2 FT-920. One of them produce RF spikes (the newer one). If you set the TRX to eg. 5W, the spikes will be full 100W. The other one doesn't (the older one). So best would be to measure

I searched the group and have not found this subject.? Does the FT-920 have an RF spike when PTT is applied?? A lot of radios of that vintage do but have not seen or heard of the FT920 having

Mark, thanks for taking the time to tell me what I should not assume and to have a dig at CB'ers ??? But you missed the point of my post, I was asking for assistance or if anyone else had experienced

never assume it needs 'finals' that's? as i quite often see a CBers diagnosis.. it could be a driver, or even an ALC problem, or power to the devices issue.. just assuming might end up fixing it,

Hello Group, my 920 started losing all tx power after 1-2 hrs use but after a while it would return and the radio would work fine , last night it finally gave up, the radio fires up and receives no

Hello friends, i have a FT-920 which has a Problem with no PLL lock (frequency display is flashing). I found that the 2nd LO isn't producing any output. So i checked Q2028, Q2029 and all surrounding

Ok, I have that executable but unfortunately, I don't have the proper old hardware to run it now, thanks a lot Jim for your generous help. 73 and any news I'll post here.

It's been a while...I think the EPROMS hold the bios and digital filter tables, the market based parameters stored in the cpu eeROM. Jim

I have used the Vertex/Standard att0274.exe and it works fine, with two prerequisites. No Windows, must be DOS. And no virtual USB comports. Must be a physical RS-232 com port.? I personally would

Hi Jim and thanks for your fast answer, i have the original main board damaged by another problem but it receives well and has the mars mod, I know of an executable file under the old DOS operating

Pablo, It's a JA market control board.? You can use it, but you'll need to install NA TX partition table, then do your hardware mod. Jim WA9Z