开云体育

when I put the SD card on the computer(windows 10), it shows NO partitions-disk management shows the card as drive E, with no partitions When it's convenient, perhaps a new .img file can be posted

“ ... ADIF log for FT8. Call signs, reports, QTH are saved. Imported to hamlog.online, eqsl.cc, qrz.com “ Where I can set / adjust the parameters for automatic log export to E-qsl ? (or

Ok , done ... seems to work the X6100 . At start-up is shows 0.22.0 73 , Jens / HB9JOI +++ Sent: Friday, August 16, 2024 4:42 PM To: [email protected] Subject: Re: [xiegu-x6100] R1CBU

DATA (F:) One of the partition of SD card have ext4 file system - it's doesn't supported by Windows. This is fine

If I put the SD-card with R1CBU FW into the computer USB ... I get two things : DATA-F and BOOT-D . To where I have to copy the new x6100_r1cbu_0.22.0.tgz ??? At firts comes a message when I

I tested only with FT8. Will take a look (but, perhaps, later).

If I put the SD-card with R1CBU FW into the computer USB ... I get two things : DATA-F and BOOT-D . To where I have to copy the new x6100_r1cbu_0.22.0.tgz ??? At firts comes a message when I

I didn't change change voice prompts, but also didn't check them. All old stuff should work.

I thought about moving spectrum to, but it requires some additional efforts. Might be changed in the next release. My bad. Didn't check it.

I agree - well done! In regards to FT4 operation - which Oleg added in one of the last revisions - any chance of work being on that? I never could get it to work properly and I suspect I'm not the

More positive observations: - I see the smoothing in the power meter looks like it's gone. I had gotten used to it in your previous version, and started using the ALC to tune my power output from

Jerry K6ANI : I was able to copy the 1.20.1 Patch into the SD card, into the DATA partition on my Windows 10 laptop. It ends up that the reason I couldn't see the Data partition on Windows File

Hi I’m blind, do the voice prompts work in this update 73 Doug in Ottawa VA3PSI Sent: Friday, August 16, 2024 9:19 AM To: [email protected] Subject: [xiegu-x6100] R1CBU firmware 0.22.0

It's exciting to see updates! I've started poking at them this morning. - I see your new version when it boots up (0.22.0) (/) - The way the waterfall moves on band changes is very nice. (/) - In CW

I do not understand the update process ... (?) : “ ... Update via patch - connect the card to the computer, and drop the tgz file into the DATA disk (for those with Linux - into the root of the

If you already have an SD card with one of the previous version - insert SD card to your computer, copy attached file to the DATA drive, insert card to transceiver and boot it.

How it is to install ? Only create a SD-Card with Balena-Etcher ? Sent: Friday, August 16, 2024 3:19 PM To: [email protected] Subject: [xiegu-x6100] R1CBU firmware 0.22.0 New: * CW tuner -

New: * CW tuner - shows how accurately the radio is tuned to the correspondent's frequency. I had to slightly change the signal preprocessing for the CW decoder - now it works a little differently. *

Hi Pavol. I never created? SD card image with new version from the scratch, even after kernel update. I always use R1CBU image as a base and copy changed parts (kernel, x6100_control, gui app, etc)

Hi Georgy, I really appreciate your willingness to carry on with development of Oleg's fimrware. I would like to add some stuff as well, but it would be really nice to have clear instructions how to