Re: R1CBU firmware 0.22.0
¿ªÔÆÌåÓý?
¡° ... ADIF log for FT8. Call signs, reports, QTH are saved. Imported to
hamlog.online, eqsl.cc, qrz.com ¡°
?
Where I can set / adjust the parameters for automatic log export to E-qsl ?
(or others)
?
73 , Jens
?
? From: g.dyuldin@...
Sent: Friday, August 16, 2024 3:19 PM
Subject: [xiegu-x6100] R1CBU firmware 0.22.0 ?
New:
*
CW tuner - shows how accurately the radio is tuned to the correspondent's
frequency. I
had to slightly change the signal preprocessing for the CW decoder - now it
works a little differently.
*
Adjusting the bandwidth for filters with one knob. I
did it for CW, but did not disable it for other modes. For CW - the center of
the filter always equals to the key tone.
*
Low and High filters in CW mode change synchronously (central frequency remain
unchanged).
*
Simple level indicator in the recorder.Perhaps, will restyle/rework it in the
future.
*
Time sync in FT8 application. When
pressed, rounds the current time on the transceiver to the nearest FT8/FT4
slot. Usage
- listen to the broadcast, find a section of silence, press the button - the
system time will be updated. I guess it's simpler, than trying to adjust using
settings.
*
ADIF log for FT8. Call
signs, reports, QTH are saved. Imported
to hamlog.online, eqsl.cc,
qrz.com
*
Noise reduction and Noise blanket can be assigned to f1/f2 headset
buttons
*
Battery icon. The
charge level is calculated by
voltage
*
Charging
icon
*
Support reading transceiver ID via CAT. Should
help solve the problem with some versions of
Hamlib
*
Display peaks on
S-meter
?
Changed:
*
FT8 app now uses USB-D. The
sound from the microphone is not mixed into the transmission, and the
transmission does not break down after using the ATU.
*
The output power in the FT8 application match to the installed
one. Looks
like for internal signal sources the changing output power only works as a
limiter (ALC threshold adjustment).
*
Auto level for waterfall/spectrum is disabled during transmission.
Fixed
values ??are used during transmission. After
the transmission is completed, the auto level is used again.
*
The buttons on the left (GEN, APP, etc.) ¡°scroll through¡± the corresponding
button blocks of buttons below.
*
Recording and playback levels in settings app are now in decibel s (default 0,
range from -10 to +10).
*
Switching to digital modes and back - by long pressing the SSB
button. Short press for the
LSB/USB or LSB-D/USB-D switch.
*
In digital mode, the LSB-D/USB-D inscription changes color.
*
Power meter, SWR and ALC smoothing is disabled in digital modes.
Fixed: * Band "jump" if the transceiver is in the lower range and is tuned to the upper limit. * Zooming spectrum doesn't affect levels. *
When changing band/A/B, the waterfall does not forget the data.
*
Deleting a single entry/message now clears the table.
*
Fixed some bugs with the FT8 application
*
Freezes when using headset buttons (possibly my mistake, but now fixed)
*
Minor stability and performance
improvements
?
Also,
I raised the recording level in the audio mixer that comes with SDR on linux and
is used for recording, CW and FT8 decoding, etc. Initially
the sound is very quiet - maybe this is a problem with my transceiver.
?
Update
via patch - connect the card to the computer, and drop the tgz file into the
DATA disk (for those with Linux - into the root of the DATA
partition).
The
transceiver will update the files on first boot.
?
|
Jens/HB9JOI