开云体育

Hi all, I wanted to check my Windows versions of fldigi, flmsg, flamp, and flrig were current, and found that sourceforge.net and w1hkj.org have different versions of flamp - 2.2.13 on sourceforge,

A few of us in the Philly region are starting a new net: *FLDIGI TRAINING NET* This may be helpful especially for rookies with FLDIGI. Net time: ?1st and 3rd Saturday of each month: ?9:00 AM Eastern

There can be many reasons Fldigi does not “print” with your setup. One rookie error is to be in LSB data mode. ?All modes are USB-D now, even on 80 and 40m where lower sideband is for phone

The Pa NBEMS net extensively tested (a few years ago) the OFDM modes on 80m Sunday mornings 0730 hr. OFDM500 was very frustrating and not very robust unless we had a very strong S/N. The 80m NVIS

Hello, My goal is to set up my FT-99!a to decode CW and send with a straight key. I am running FLDIGI ver. 4.2.05 with FLRIG 2.2.05. Rig control seems to be operating correctly. Right now, I can hear

I am using Fldigi 4.2.06. I have Rig Control set for "Use Hamlib". For the Hamlib "Rig" setting I have "Icom IC-707 (Alpha)" selected. Other then the Hamlib "Device" and "Baud rate" settings, all

Is there a way to get the user interface to come up when the flrig comes up. Just found how to do the auto start in fldigi. Dan KG7AFL

Excuse me if this is a duplicate post. I just downloaded FLDIGI last Sunday and have been trying to get it to work with my Yaesu FT-991A. After a lot of frustration, I've almost got it right. However,

Fernando, I am successful with getting fldigi to send to the log on Log4OM2. following the information from you. The function I am trying to replicate is the call lookup done at the beginning stage of

For those who have tried the OFDM modes, please note: 1. designed to operate at a fixed audio center frequency 2. DCD off not implemented, basically runs without squelch 3. not suitable for HF

I agree Robert. The OFDM modes were introduced as experimental, and the original developer, John, KL4YFD, is not an active developer at this time. David [email protected]> wrote:

Hi Bill, If you'll allow me, I suggest you ask this same question on the Log4OM forum. Since it works as desired in ACLOG and not in Log4OM, I imagine it is something on Log4om's part. Even though I

The on going Saga of the OFDM modems, might be a good idea to just remove them until they get fixed, way to may issues. The PSK modems work well enough. Robert

I am trying to find out how to have a call sign entered in Fldigi get looked up in Log4OM2 so as to see if it was worked before. I have been unsuccessful in finding any information. When Fldigi is

There's definitely something not right with the way OFDM modes function in fldigi.? When I set fldigi to OFDM3500 centered at 1625 and send a message the station on the receiving end sees only

A further look indicates both OFDM500 and OFDM750 have this issue while OFDM3500 behaves correctly. On the initial modem switch squelch is operating correctly and as you decrease squelch level to

Looks like the squelch does not have the desired effect with this modem. Dropping the squelch value for OFDM3500 has the same effect. Robert

When selecting Mode OFDM750F I get a non-stop run of text characters across the screen that do not stop unless I select a different mode (such as OFDM500F or OFDM3500). Why is this and is there a way

I have to echo the above suspicions about RFI. Program crashing plus the transceiver locked in transmit sounds very RFI-Like. In addition to the suggestions about grounding and using ferrites, I have

Make sure each piece of station equipment is bonded to a single common point. This includes the station computer as well. I make my bonding jumpers using #10 AWG auto primary wire with a ring terminal