Relay
What is a "throat" controlled relay? I did a Google search of the net and could not find an answer. Thanks Don
By
Donald Scharenbroch
·
#13046
·
|
Re: Reversing
Did the picture not come through? Here it is again. The Bachman stock number is 44547. Charles
By
Charles Brumbelow
·
#13045
·
|
Re: Reversing
Charles Brumbelow...what is the Bachmann track system? Thank you...Jody Correro "Life is not measured by the number of breaths we take, but by the moments that take our breath away!"
By
Joseph A. Correro, Jr. <joedeyejr@...>
·
#13044
·
|
Re: Reversing
Bachman offers a track system for this. Might be what you want. Charles
By
Charles Brumbelow
·
#13043
·
|
Re: Reversing
Thanks Don!!!
By
Appel
·
#13042
·
|
Re: Reversing
Thank You!!!!
By
Appel
·
#13041
·
|
Re: Peco Crossover
Since you said that you swapped the wires to the Tortoise 2 and 3 pins and you got the same result tells me that something is wired wrong.? You can troubleshooting with your DCC power, but it might
By
Allan AE2V
·
#13040
·
|
Re: Reversing
Provide a human operator to watch the loco as it gets near the end of your test track and press the appropriate buttons on the DCC throttle to slow down, stop, pause(?), start up again in the opposite
By
Don Vollrath
·
#13039
·
|
Re: Reversing
The NCE product called the Mini-Panel should do the trick.? You will need a couple of trip sensors for each stop point.? You can use the NCE BD-20 block detectors or you can use an optical sensor
By
Allan AE2V
·
#13038
·
|
Peco Crossover
I rebuilt one of my single crossovers using peco unifrog turnouts.? The switch machine is a tortise and the controller is a digitrax ds 64.? After installing the cross over, I test ran several
By
htn1680
·
#13037
·
|
Reversing
Hi everyone, I have a part of my HO layout where I want to just run a train back and forth a distance of about four feet. ?How do I run the train forward, stop it at the end and reverse it and do the
By
Appel
·
#13036
·
|
Re: messages
Hi Tom and any others new to this group: You should be able to receive messages.? If not, make sure they are not ending up in your junk folder. New members:? Your first message is moderated just to
By
Allan AE2V
·
#13035
·
|
messages
I would like to send and receive messages. Thanks Tom Appel tapplfam@...
By
Appel
·
#13034
·
|
Re: Seeking reversing section input
My apologies, I'm traveling at the moment and don't have access to my plan. Once I'm back next week I'll label and re-post so it's clear where my concern is. Get Outlook for
By
Nick Ostrosky
·
#13033
·
|
Re: DCC system resets when accelerating locomotives
Good point!
By
Phil T. <affirmtraining@...>
·
#13032
·
|
Re: DCC system resets when accelerating locomotives
Phil, Don't forget to also check all of the gaps - the ones you want/plan to have. If one of those has closed up ... most of the way but not all the way ... that can cause a short/intermittent
By
Jim Betz
·
#13031
·
|
Re: DCC system resets when accelerating locomotives
Not yet, but I'm planning to. Dealing with an aging dog who has been an extraordinary companion.
By
Phil T. <affirmtraining@...>
·
#13030
·
|
Re: DCC system resets when accelerating locomotives
Hi Phil, Have you tried any of the things Marcus Ammann suggested? Allan
By
Allan AE2V
·
#13029
·
|
Re: Seeking reversing section input
Once you get going CCW around the main loop there is no way to change the direction to go CW without backing up. Is that what you want? DonV
By
Don Vollrath
·
#13028
·
|
Re: DCC system resets when accelerating locomotives
On Mon, Sep 20, 2021 at 3:28 PM wirefordcc <bigboy@...> wrote: > Hi Phil, > > I'm still perplexed by your problem. *Me too!* Since you have your Power > Cab displaying track current, what
By
Phil T. <affirmtraining@...>
·
#13027
·
|