开云体育

After further organizing my storage facility, I have found the following items: ICOM UX-59A 6M band unit for IC-900/901 - New and unused. ICOM UX-39A 220 band unit for IC-900/901 - New and unused. ICOM UX-129A 1200MHz band unit for IC-900/901 - New and unused Asking $200 each plus shipping from 95762 RLC-ICM ICOM IC-900/901 Band Module Controller. Includes 4 interface boards, ribbon cables and metal case - New and unused Asking $200 plus shipping from 95762 CommSpec TS-32P CTCSS Encoder/Decoder - New and unused - ( I have 5 ) CommSpec TS-64 CTCSS Encoder/Decoder - New and unused - ( I have 2 ) CommSpec DCS23 DTS Encoder/Decoder - New and unused ( I have 3, one without the manual ) Asking $50 each - Free Shipping I accept Venmo or Zelle. If interested, please PM me. Thanks and 73, Craig (AA6CG)

Has anyone successfully interfaced an external MMDVM board to the RS-232 accessory connector on the Kenwood NXR repeater? I know the pinouts between the TKR-850/1 and the NXR appear identical in terms of what's required to tie to a MMDVM (the RB board for e.g), however I'm wondering if the NXR may be prone to audio phase distortion should it use a DSP based discriminator similar to a Quantar or XPR etc. Anyone using one of these on DMR or P25 that can confirm it does or does not work with the external digital modem? Regards Kirb. VE6IV

Looking to swap a brand new ics control quantar 1x for the northcomm quantar ecm and program cable. I'm looking for a more simple plug and play solution than something I need to jump through all sorts of gyration to get up and running. And I don't need all the capabilities of the ics I just need remote disable, and courtesy beep. So the northcomm might be better for me and the ics might be suited to someone who has more patience than i do to set it up properly and needs the advanced functionality of the ics. I'm only using this on a gmrs repeater so I don't need a bunch of advanced features or digital linking. My understanding is the northcomm is just set wildcards in quantar and then 1 adjustment on the board that requires no test gear to set it up. Suffice to say I can't get courtesy beep or remote disable to function on my quantar with the ics and the ics is brand new. I got voice id'er to work fine so I'm sure it's a setting on the ics board. I'm just out of patience to screw with it. I want an overall plug and play unit. I will also sell the ics outright for what i paid for it in leu of a swap. Let me be clear it's not ics fault it's l something I'm not doing correctly and I don't have the eyesight or dexterity in my hands anymore to work with small stuff like this board. Thanks Robert Chrysafis Kc8gpd Wrcm325 Scottsbluff NE

Motorola VHF Quantar SN 509CLR1418 stolen from site last Thursday... Along with DB4060B ...missing mounting brackets. Both tuned to 146.36/96 pair they cut the tie wraps holding the 4 cans together..the brackets had been misplaced but found and were to be reinstalled when repeater was discovered missing Also cables from rptr to duplexer and duplexer to Heliax gone....Sinclair Duplexer in cabinet that the rptr was sitting on not touched nor a UHF MII repeater...so this was personal....and I have 4 suspects in the list. Sheriff's office has been contacted. Contacting Boone Co Iowa (ironic) where the duplexer was bought from to get the SN on both units bought..lost the paperwork Chris WB5ITT

Have two Kintronic isocouplers VHF FMC-0, large style. Came out of service working when tower was converted. Those folks on an AM "hot" tower know what these are. Free for shipping costs, estimate $60 each to ship inside the US. Contact me directly if interested. Chris - KC4CMR

Hi, I own a MTR2000 UHF Low Band High Power. Apparently there is a way to get this low band within the ham band (430-440). I once saw a description on the repeater-builder website but can't find anything about it anymore. Is there anyone who can help me on my way? Thanks in advance, Manu - ON7FQ

Hello everyone, i am trying to programm my TB7100 Vhf to worked with Scott RB-USB RIM "Lite". Anyone has done it and if so maybe he could share the file of this repeater or just a picture where i should go to set it up! i am almost ok,my AllStar 2.0 is transmetting but it does not hear me but first i need to be sure the Tait is ok! thanks in adavance for your help, it will replace a simplex node here. 73/s Gervais,ve2ckn

Hi to All, I just bought a nice Motorola CDM-1250 Low-Band modified for 6 Meter Ham Band. But I am looking for the Service manual and I can only find the manual for VHF and UHF. The radio does work and turn on by the ignition accessories plug pin but I have some problem with the control head. No ON-Off button function, no Lights for the display, no RX-TX light, no Lightening of the DTMF Mike. And I have some question on the output power specs of this radio, it is set to 65 Watts in CPS put putting out 90 W on my Bird Bench Wattmeter? My Model is : AAM25DKD9AA2AN I am hoping that a member as seen this control heads problem before and somebody as the proper manual for this radio. Or at least the model number info to know what is the normal output power of this radio? Thanks’ to all for looking in their electronic document file. Best 73 Carl VA2CMB

Good afternoon everyone, I bought this on eBay as it says in the link below, but as it turns out, I won't need this so if anyone needs it, I sell for $10 It's brand new in the package and never opened > https://www.ebay.com/itm/185753551768?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=tbBinouRQq-&sssrc=4429486&ssuid=GWF0AxjSQFG&var=&widget_ver=artemis&media=EMAIL > > Chad Nelson WI9HF/WRPL979 > Janesville Wisconsin > 608-754-8671 > Send from my spectrum iPhone 16.

Hi, I hope someone can help me figure out an issue. I am trying to use a West Mountain Radio Rigblaster plug and play sound card interface to run echolink. The issue I am running into is that I use JAWS a screenreader that reads text outloud from the computer since I am totally blind. When I have my nomic working JAWS talks fine and everything is happy but when I connect the plug and play, I get the usual computer sounds out of my speaker, but JAWS doesn’t talk, (so I can’t do anything if it doesn’t read to me what is on eht screen). Does anyone have any ideas or how to make an external sound card play nice together with the internal one. I would be happy to use the internal card for JAWS, and use the USB card to run the plug and play, but I run into the same issue with the USB sound card. Thanks, Chad

I'm trying to figure out why our mtr2000 isn't passing any audio. We're using an external repeater controller through the wireline connector. This is new to us, and we're trying to get things set up before we go to the site. Before I try too hard and break something... Is that 4 pin connector (J6) supposed to come off? How do I release the wires? I tried pushing into one of the small holes, figuring that would release a clamp. The wires aren't budging. Thanks. Don

I am seeking advice where the RF feedline grounding/lightning arrestor block should be mounted to. I'm working on a project where the ham station is in the mezzanine of a warehouse where the tower was installed on TOP of the roof, with a seriously over-engineered mount in the middle of the building metal structure. The entire building has a ground rod ring around it that are connected to a 6" copper strap that does not NOT contact to the building. Near the coax entry point there is a building structural I-beam. The copper ground strap comes up along the outside side of the building, galvanically isolated, through a plastic tube and junction box, into the shack. So, for best lightning/EMP protection: 1. should the ground strap be sandwiched between the building i-beam and the ground block, or, 2. should the ground block be connected to the copper strap secured by some kind of isolating material from the metal building? If typing words is not your forte'; email direct for my cell number. Benjamin, KB9LFZ

Good morning, This question is for all the 220 MHz repeater owners on the list. We have a 25W repeater and would like to add an amplifier as it hears much better than its transmit coverage. Our exciter output is variable from 1 to 25 Watts. Our antenna is a DB224-JJ. What type of amplifier are you using? I’m really looking for options other than Henry and TE Systems but not seeing very many. James Adkins, KB0NHX Repeater Trustee - Nixa Amateur Radio Club, Inc (K0NXA) www.nixahams.net

Kevin has given me a lot of help tuning the overpainted and unknown dB4060 diplexer. It is smelling a lot like they are not the ham band model. If anyone has up to date contact info on the firm called duplexerrepair.com I would greatly appreciate it. If anyone has extra -005 coupling assemblies, please let me know, off list. Jerry W6OJE gvlucha@...

I've got a TB8100 in GMRS service. I want to of course provide proper ID, but as I share the channel with another system, I do not want the ID to beacon, just politely properly ID routinely after use of the system. In the CWID System tab, pretty sure I do not want Automatic CWID checked - but ID after some period of local system use would be done via a Task Manager configuration? Examples, screen shots welcome.