开云体育

Hello everyone, i am trying to programm my TB7100 Vhf to worked with Scott RB-USB RIM "Lite". Anyone has done it and if so maybe he could share the file of this repeater or just a picture where i should go to set it up! i am almost ok,my AllStar 2.0 is transmetting but it does not hear me but first i need to be sure the Tait is ok! thanks in adavance for your help, it will replace a simplex node here. 73/s Gervais,ve2ckn

After further organizing my storage facility, I have found the following items: ICOM UX-59A 6M band unit for IC-900/901 - New and unused. ICOM UX-39A 220 band unit for IC-900/901 - New and unused. ICOM UX-129A 1200MHz band unit for IC-900/901 - New and unused Asking $200 each plus shipping from 95762 RLC-ICM ICOM IC-900/901 Band Module Controller. Includes 4 interface boards, ribbon cables and metal case - New and unused Asking $200 plus shipping from 95762 CommSpec TS-32P CTCSS Encoder/Decoder - New and unused - ( I have 5 ) CommSpec TS-64 CTCSS Encoder/Decoder - New and unused - ( I have 2 ) CommSpec DCS23 DTS Encoder/Decoder - New and unused ( I have 3, one without the manual ) Asking $50 each - Free Shipping I accept Venmo or Zelle. If interested, please PM me. Thanks and 73, Craig (AA6CG)

Has anyone successfully interfaced an external MMDVM board to the RS-232 accessory connector on the Kenwood NXR repeater? I know the pinouts between the TKR-850/1 and the NXR appear identical in terms of what's required to tie to a MMDVM (the RB board for e.g), however I'm wondering if the NXR may be prone to audio phase distortion should it use a DSP based discriminator similar to a Quantar or XPR etc. Anyone using one of these on DMR or P25 that can confirm it does or does not work with the external digital modem? Regards Kirb. VE6IV

Have two Kintronic isocouplers VHF FMC-0, large style. Came out of service working when tower was converted. Those folks on an AM "hot" tower know what these are. Free for shipping costs, estimate $60 each to ship inside the US. Contact me directly if interested. Chris - KC4CMR

Good afternoon everyone, I bought this on eBay as it says in the link below, but as it turns out, I won't need this so if anyone needs it, I sell for $10 It's brand new in the package and never opened > https://www.ebay.com/itm/185753551768?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=tbBinouRQq-&sssrc=4429486&ssuid=GWF0AxjSQFG&var=&widget_ver=artemis&media=EMAIL > > Chad Nelson WI9HF/WRPL979 > Janesville Wisconsin > 608-754-8671 > Send from my spectrum iPhone 16.

Hi, I hope someone can help me figure out an issue. I am trying to use a West Mountain Radio Rigblaster plug and play sound card interface to run echolink. The issue I am running into is that I use JAWS a screenreader that reads text outloud from the computer since I am totally blind. When I have my nomic working JAWS talks fine and everything is happy but when I connect the plug and play, I get the usual computer sounds out of my speaker, but JAWS doesn’t talk, (so I can’t do anything if it doesn’t read to me what is on eht screen). Does anyone have any ideas or how to make an external sound card play nice together with the internal one. I would be happy to use the internal card for JAWS, and use the USB card to run the plug and play, but I run into the same issue with the USB sound card. Thanks, Chad

I'm trying to figure out why our mtr2000 isn't passing any audio. We're using an external repeater controller through the wireline connector. This is new to us, and we're trying to get things set up before we go to the site. Before I try too hard and break something... Is that 4 pin connector (J6) supposed to come off? How do I release the wires? I tried pushing into one of the small holes, figuring that would release a clamp. The wires aren't budging. Thanks. Don

I am seeking advice where the RF feedline grounding/lightning arrestor block should be mounted to. I'm working on a project where the ham station is in the mezzanine of a warehouse where the tower was installed on TOP of the roof, with a seriously over-engineered mount in the middle of the building metal structure. The entire building has a ground rod ring around it that are connected to a 6" copper strap that does not NOT contact to the building. Near the coax entry point there is a building structural I-beam. The copper ground strap comes up along the outside side of the building, galvanically isolated, through a plastic tube and junction box, into the shack. So, for best lightning/EMP protection: 1. should the ground strap be sandwiched between the building i-beam and the ground block, or, 2. should the ground block be connected to the copper strap secured by some kind of isolating material from the metal building? If typing words is not your forte'; email direct for my cell number. Benjamin, KB9LFZ

Good morning, This question is for all the 220 MHz repeater owners on the list. We have a 25W repeater and would like to add an amplifier as it hears much better than its transmit coverage. Our exciter output is variable from 1 to 25 Watts. Our antenna is a DB224-JJ. What type of amplifier are you using? I’m really looking for options other than Henry and TE Systems but not seeing very many. James Adkins, KB0NHX Repeater Trustee - Nixa Amateur Radio Club, Inc (K0NXA) www.nixahams.net

I've got a TB8100 in GMRS service. I want to of course provide proper ID, but as I share the channel with another system, I do not want the ID to beacon, just politely properly ID routinely after use of the system. In the CWID System tab, pretty sure I do not want Automatic CWID checked - but ID after some period of local system use would be done via a Task Manager configuration? Examples, screen shots welcome.

Hello all, would anyone have any tuning information on the Varden duplexer 146-148mhz. I know its a long shot, but no searches on the web produced any results. These were made by Varden Electronics Box 791, Jackson, Michigan 49204 Thanks for any information

I recently had the need to do some research on Helper Instruments and locate a schematic. I ended up overhauling the page at Repeater-Builder. Does anyone know what Bill Detweiler's ham callsign was? It's undoubtedly been reissued... Neither the ARRL or the RCA have that... Does anyone know who the rest of the Helper people were? Or what happened to them? Maybe you have an old business card in the back of a desk drawer? If anyone has the missing applications notes it would be nice if we could offer them for download. If all you have is a paper copy we'd be happy to scan it and return it. The missing ones are: Everything you need to know about SINAD Line Measurements Speed Control System Troubleshooting What the Modulation Monitor Has Missed Troubleshooting With Your Power Supply R.F. Voltmeters Thanks in advance

Hi, Does anyone know what version 2 UHF radios in the commercial line will operate 440-470 straight through without retuning? I have the TK 8180 which works great in that range, the TK 8302 needs tweaking every couple of MHz. Interested to know what other radios will do this that have a front mounted speaker? ~Thanks, Chad