开云体育

I concur with Neil. When I installed Teamviewer on Ubuntu I was horrified at the background processes that it installed silently. It took hours to remove all the garbage. I would not recommend

or dwagent by dwservice.net 73 Danny, K5CG HH 550-0609 SKCC 14257 To: "linuxham" <[email protected]> Sent: Wednesday, April 23, 2025 6:10:18 AM Subject: Re: [linuxham] Teamviewer on Debian

Adrian, all, I would advise against using TeamViewer, as it currently has concerning security issues, and might as well be malware. I suggest using RustDesk instead. It's an open-source alternative

The Country (CTY) Files were updated on 22 April 2025: https://www.country-files.com/cty-3512-22-april-2025/ For installation instructions, start at: https://www.country-files.com/ Hover

This is untested, but give it a try. It uses the XML interface that is included in fldigi (and I think it was made so that you could do exactly what you are wanting to do!) Make sure you have: *

OK after some head scratching and deep reading, the fix is simple. kcat uses obsolete method main.get_frequency. The new method is rig.get_frequency. I changed that in src/support/xml_io.cxx and now

Once the port is configured, could you perhaps ln -s the file .fldigi/talk/output.txt in your home directory to your serial device /dev/ttyUSB0? Everything's a file in Linux.

In the Misc section of the FLDIGI configuration you can choose 'RX text capture' and enable 'rx text stream' in the window that pops up. That stream goes by default to .fldigi/talk/output.txt in your

Sure: cat textout.txt > /dev/ttyUSB0 --David KI6ZHD

Nice! That is a bit easier to use, and I did not find it. Any way to redirect that directly to the serial port? (USB) Sent: Friday, April 18, 2025 1:29 PM To: [email protected] Subject: Re:

Look at the $HOME/.fldigi/talk/textout.txt file --David KI6ZHD

Greetings: I have setup an RTTY -> phone -> modem ->ASR-33 demo here at the Computer Museum @ System Source (Hunt Valley, MD) ( https://museum.syssrc.com ) I am taking an RTTY Feed, (for example

Tried a couple earlier versions, including 4.1.17 from 2020. Same behavior as the newest version. So I guess it's nothing in the new code that broke it. And maybe I'm dreaming that it ever

Hi Dave. Not seeing the accumulated logs (and a lot of other problems) maybe a result of that change some years ago to use $HOME/.fldigi/.fldigi when it was previously just $HOME/.fldigi eg my older

I found Dave's archive of tarballs. I'll try some of those to see if going back fixes this.

I use kcat all the time and it works great. I use fldigi only now and then. But I built fldigi from source yesterday, to get all the new-and-improved, all looked clean. But now doesn't work with

Hi again. OK, I've tried every which way and then some. I can get the new .07 alpha to restore my station and operator details, the view window layout (including the "show all 48 macros" setting)

The Country (CTY) Files were updated on 12 April 2025: https://www.country-files.com/cty-3511-12-april-2025/ For installation instructions, start at: https://www.country-files.com/ Hover

When I connect fldigi to be controlled via flrig (ft-817), flrig closes unexpectedly. It even opens the window to report the problem via bugzilla. I can only use Flrig if I am disconnected from

This is not a font change Dave, but a translation table change. The missing character will be the pound sterling symbol. [image: image.png] The translation change is for the " ' " and bell