开云体育

Thanks for that info Bob, I have run the command and I get: sudo lsof -i -P -n | grep LISTEN vncserver ? ?861 ? ? ? ? ?root ? 11u ?IPv6 ? 2981 ? ? ?0t0 ?TCP *:5900 (LISTEN) vncserver ?

Thanks Dave, I assigned a button in the macros to BU0; and BD0; which tells the radio to go up or down a band, and using this it transfers the ant selection and the tuner selection and also the NB

Hi David IC-7610 Time sync no work, please help to check, thanks! 73 Yip VR2VRC

The Country (CTY) Files were updated on 17 September 2024: https://www.country-files.com/cty-3433-17-september-2024/ For installation instructions, start at: https://www.country-files.com/ Hover your

http://www.w1hkj.com/files/flamp Index of /files/flamp * Parent Directory <http://www.w1hkj.com/files/> * Amp-2.V3.0.Protocol.pdf <http://www.w1hkj.com/files/flamp/Amp-2.V3.0.Protocol.pdf> *

Thanks Robin, Yes I got it working nicely with rigctld, but just thought it was messy doing it that way. As far as the antenna switching goes, using the additional commands settings, it does not

The correct command sequences for selecting antennas are AN01;? ==> antenna 1 AN02;? ==> antenna 2 AN03;? ==> antenna 3 to read the current antenna selection AN0; The response will be AN010; AN020;

Hi Robin, Thanks for the answer, not sure what happens when it switches between vfo's on startup and shutdown, but trying to see what if anything changes and from where the change comes. Not sure if

Index of /alpha/flrig * Parent Directory <http://www.w1hkj.com/alpha/> * darkscheme.UI.prefs <http://www.w1hkj.com/alpha/flrig/darkscheme.UI.prefs> * flrig-2.0.05.75.dmg

The Country (CTY) Files were updated on 14 September 2024: https://www.country-files.com/cty-3432-14-september-2024/ For installation instructions, start at: https://www.country-files.com/ Hover your

On that note, often the portion of the OS responsible for directing the packets to the correct process doesn't and can't know the difference between those wrote:

Robin/Phil To show listening sockets (aka servers) on a Linux terminal; sudo lsof -i -P -n | grep LISTEN or sudo netstat -tulpn | grep LISTEN of course also possible to check a particular port In

Phil, if there's no server running that's listening on port XXXX, then the OS has nowhere to forward any connection request to. That triggers the “actively refused” response from the OS.

Flrig these days, has a slide out button panel for "Extra Commands" that are user configurable, plus such settings get saved when you exit Flrig, and re-appear the next time you start Flrig. I use

Thanks Robin, So it's not the server app that's "actively refused" the request but the OS the app is running on. I'll bear that in mind when I next drill down into my remote operating. Phil GM3ZZA

John GW0WZL, please see reply in message /g/linuxham/message/53331. Adding to that, I recall Dave, W1HKJ, noting that on the start-up of flrig the VFOs are somehow explored. If the

Phil, John (GW0WZL), it's not a left-right pondian issue. “Actively refused” means that the operating system (OS) has decided not to accept any connections on, in this case, port 4532. That will

Hi Cliff, I can't pin point any particular mode. This net did send a few Flamp's using 8psk1000f and I was receiving. I wasn't running Fllog and the only connection would have been local host to

Ron, Is this on all modes or only one mode? Fldigi will hang for 10 seconds or so if it loses it networking connection with fllog. It may also if it loses Internet connections. Need to check that one

Hello Dave and the rest of the talented programming team. My system is Linux Mint 22 Cinnamon. I use the Wiki to build the Fldigi suite. When I use Fldigi for a while, like on a net, it will freeze.