开云体育

100w all they got?told “hours of digital” like hours, non stop slow saturation effect. kelly

How much power did it take? Micky K1XH Links: ------ [1] /g/ldgelectronics/message/1040 [2] /mt/96716924/1045683 [3] /g/ldgelectronics/post [4]

Friend had a little to much FT8 fun, looking to replace or fix, looking for replacement details for the FT114 sized?Toroidal *?* thanks kelly

Yes... See previous reply below.? /g/ldgelectronics/message/1033

Have you tried pressing the Z-11's Tune button? ? The Z-11 initiates the tuning cycle. 73, Ed - ad7gr

I've searched high and low in both the menus and the manual (including keyword searches) and I have not found anything that suggests a solution to use the Tune button on the Rig for anything other

With the rig's internal tuner turned off, there must be an additional setting to make, perhaps in the dx10's Menu.?? Sorry, but I don't have a dx10 to investigate this issue. 73, Ed - ad7gr

Same here with my FT-891 and Z11Pro Ron, and also with the FT-dx1200 I had years ago. 73, Ed - ad7gr

Ron wrote: "Can you push TUNE on the Z11 to get the rig to tune.? I do this with my FT817 and LDG Z817 tuner.? Also did with the FT891 and Z11pro." Yes, when I press Tune on the Z11, it will request

Can you push TUNE on the Z11 to get the rig to tune.? I do this with my FT817 and LDG Z817 tuner.? Also did with the FT891 and Z11pro. 73, ron, n9ee/r Ron Wright, N9EE/RHernando Co ARES EC Spring

Ed - I made the electrically equivalent Y-ACC-2 cable... No joy on pressing Tune on the FTDX10 transceiver and getting the LDG Z11ProII to tune regardless of the Tuner Select is set to INT or EXT.?

Spencer, I use an FT-891 with a Z11-ProII and my homebrewed cable; equiv. to LDG's Y-ACC cable.?? I set the FT-891's Menu 15-16 to LAMP.?? Tuning is initiated by a press of the tuner's [Tune]

Ed - I do not observe a difference in how the LDG tunes when the radio is set to INT or EXT.? It'll request a tune either way.? Didn't try ATAS. Spencer

Thanks Spencer Did you change the general/tuner select option to ext or atas to make this work? Or leave at default of int? thanks EdWA7EM

Hi, Just turn on ATAS mode, QSY to your operating frequency, change to AM mode and set to 5W power, press PTT and up or down button at same time, the RT-100 shall auto tune. Afterward, return to yr

To followup:? ?I purchased an LDG IC-109 cable, which has only 3 pins wired from the 10 pin DIN to the other 6 pin end.? Fortunately, 2 of the wires are the correct 2 wires (pin 10 and 3).? The 10

On the qrplabs groups.io site, you will get a flood of comments about the qprlabs products not protected from the high swr that will probably occur as an auto-tuner searches for the best match. What I

My issues were with newest Yaesu models the YT-1200 was supposedly compatible with. As I recently posted, my used YT-1200 needed a newer ROM to work with my FT-991a, but LDG provided it after we

https://www.ebay.com/itm/143641554052?var=443916902538 -- v/r SWW "Dominari et regere ad network" --- https://pgp.mit.edu *Fingerprint*=7016 2E3A 751C 2501 8F3D 4530 26B3 2B12 4312 CC25 |_|0|_||_|_|0|

I have an FT-DX10 and an old LDG YT-1200 .? I am curious if they are compatible.? The YT-1200 was designed to interface directly with older Yaesu radios such as the FT-DX1200, FT-450, FT-DX3000 via