开云体育

It looks like FTDX10 has 8 PIN mini DIN not 10. Would the pins be the same? 73.

Thank you for your comments, N0YWB.? I was one of the confused. I built a DIN8 to TRS cable per another users implication that they got it to work and it failed to work for me.? So, I have a DIN10P

I see a lot of confusion and mis-assumptions being made regarding the use of LDG auto-tuners with Yaesu transceivers. NONE of the LDG autotuners directly interface with the serial communication of the

Thank you for the diagram Jeff.? I purchased the TRS connector and a mini DIN 8 cable and soldered the GND pin to the sleeve and the Tuner Sense pin to the tip.? Powered down my radio, connected the

HRO did sell the Z100/IC705.? Was same tuner, but it came with the command cable for the IC705 and the RF coax for connecting the 705 to the tuner (BNC to PL259 cable).? And the IC705 could command

Typo: The 3.5 mm RING? on the tuner is _START, and is not connected.

T-ACC-2 cable pinout: The 3.5mm TIP (_KEY) on the tuner goes to pin 10 (TX-REQ) on the LINEAR receptacle. The 3.5mm SLEEVE (GND) on the tuner goes to pin 3 (GND) on the LINEAR receptacle. The 3.5mm

The Z100 has been replaced with the Z100Plus. It has the same 3.5mm TRS control interface receptacle and 5.5/2.5mm coaxial power receptacle as the original Z100. The Z100A uses a single 6 pin mini-DIN

I have a 1000 Pro ll. Used it for about a month and got an Amp that does 1.5 KW.? So I bought a new tuner that would handle that power. I didn't think the LED meter was accurate so I sent it in for

Hi Everyone, I have a second hand Z-100 coming to me soon, so I've been reviewing the manuals and documentation for it to get myself acquainted. I've found that it seems to have been replaced by the

Hello everyone So I also need to make this cabe for my FTDX10 / 200ProII. I downloaded?Y-ACC-2 CABLE.PDF and looking at it I see Wire Address table but it only lists Red end Black. The TRS plug also

email me price for the M-1000 and the AT-1000 please. Ron N4SFU rhill2@...

Great news tell me how you want to proceed. Sent from Mail for Windows Sent: Tuesday, January 17, 2023 3:24 PM To: [email protected] Subject: Re: [ldgelectronics] AT-1000 PROII [Edited Message

I have a spare M-1000 if you need one.

Thanks for documenting/sharing the cable build. Greatly appreciated. Will give it a try here. 73, Steve KE4LC

Hello everyone! I thought I would circle back after I had an opportunity to build a cable for my Yaesu FT-DX10. Even though it was possible, I did not want to use the Linear port on the FT-DX10 to

I just up graded from the 600 to the 1000 but do not have a meter for the 1000. Will my M-600 work or are you using a different meter since they don’t make the M-1000 any more? Thank you. Sent from

And two more ideas: 1)? Your antenna is exhibiting a higher impedance than the AT-100 Pro II can handle 2)? You have the rig's internal tuner enabled.? One or the other, but never both. The AT-100

2 ideas Is your auto tune threshold set to low? Switch off auto tune. 72 de Bryan, k0emt

Now that my remoted AT-600 Pro II seems stable, I was surprised when the SWR rose while in an extended set of FT-8 QSOs running 100 watts.? I set the radio to FM and went key down.? This was putting