开云体育

Hi All, I have transferred my JMRI files across to my Rasberry Pi but cannot seem find the operations file for my Wagons, can anyone tell me where to find them on my win10 machine. Thank you Brian

Running with the Pi 3B+.? ?I have a heat sink on mine and noticed it running hot so I added a fan on the case.? I have another 3B+ runing Retropie for games.? Dont have to use a fan on it.? I'm

Bob: This is the link I used to try to reduce the temps on my very early score of a Pi4... https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=243500&p=1490467&hilit=vl805#p1490467 Worked, but I

No overheat issues on the Pi4???? I have been holding off given? the buzz on the forums about the thermal issues. Stretch is a known no-go on the Pi4+?

Thanks Stuart. I have just rewritten the software in my current LCC hardware clock to use the draft time protocol.? I can use a minute change watcher to send the info but as 4.14 and 4.17 release

Thanks Matt John

Don The autodetect mode of Steve Todd's RPi-JMRI image can only detect the DCC system interface, not the command station type, and has a "DCS100 (Chief)" command station as default in the profile

Luke, The tests have shown that it's not simply a baud rate issue. Make sure the baud rate is back to 19200 to match the jumpers. Did you notice any LED activity (either one) during the tests? Please

Another issue. Is there a way to make the xset cmds a permanent setting. It appears i need to set these each time i boot up. Don [email protected]> wrote:

It was a bad connection in my wiring. The switch servo works good using the loconet switch LT1 with the Pi. Please ignore the previous post. Control both from the panel and the Zephyr. Now to test it

Alright so i think i? have successfully re installed the driver. The comport now shows up as 10 and i have changed to port 10 in decoder pro preferences. Here is my log 2019-09-10 22:45:36,071

Nom, There are few known bugs with the implementation.? This is one of them.? There is a hardware fast clock in development that will work with the JMRI fast clock over OpenLCB/LCC.? I'll ping the

No problem Dave! Thank you for repsonding. Here is my 9600 baud JMRI log 2019-09-10 22:25:50,223 util.Log4JUtil? ? ? ? ? ? ? ? ? ? ? ? INFO? - * JMRI log ** [main] 2019-09-10

Marc, Table attributes are stored in the user-interface.xml file, not a panel xml file. Find the node identity line near the beginning of the system log: 2019-09-10 21:17:38,917 node.NodeIdentity INFO

Hi guys, hope you can help here.. Test setup using a DCS51, Zephyr x, with locobuffer USB. Using a single turnout to test on a breadboard. Without a connection to the Pi except as providing power to

The DS64 can be programmed via a JMRI "Roster" entry. This is a relatively-recent addition to the "Roster" capabilities. The "Roster" is commonly accessed via the "DecoderPro" entry mechanism for

Luke, Thanks for the system description and log. The first troubleshooting step is to go to Advanced Connection Settings and change the baud rate from 19200 to 9600. Do not change any board jumpers or

Klaus, I sent the config? file to files/VSD.? I see it there.? no sound files sent and yes I have watched Mark's youtube many times.? it's how i got into VSD. conrad

Thanks a lot Matt. It even works with my TOR browser. And that capability is even more important to me. Peace. Mike G.

After testing over the past few days, I've now changed the server configuration to always serve content over HTTPS. Whilst it would be advisable to update bookmarks, it's not 100% necessary as the