开云体育

You can meet a (downunder) JMRI developer at the New England Convention 2018. I'll have a clinic table there. Gerry Hopkins will also have a clinic table and do a presentation. -- Dave in Australia

Did this question perplex everyone?

Thanks Spuds McCat.... but I do not understand your suggestion... where is that switch? Also, how is this any different from using mast logic without a virtual mast down the wrong way where a thrown

Different model devices use different approaches. A lot of them use port 80,but some use slightly different commands over the link. Do you have a link to a manual for the device you’re using? Bob

Marc, Since I still plan to install?new Econami's, should I disconnect the PTB? John To: John Parrish <johnreesep@...> Sent: Thursday, March 8, 2018 9:07 PM Subject: Re: Yahoo JMRI : Issues

I get the screen like your?first one below only it's not a Preference screen:? see my first screen photo on the left below.?? You're right....I also got?the Massoth 123 reading when I tried?to

OK, good to know Gerry.? I got it working now (and you will see my response to another user). Thanks. John To: jmriusers@... Sent: Thursday, March 8, 2018 8:11 PM Subject: Re: [jmriusers]

Thanks Dave Duncan in Australia as well *Duncan Cabassi* *Sinnamon Park,* *Brisbane, **Australia, 4073* *Mobile: +61 424844807* jmriusers@...> wrote:

John Soundtraxx say that the PTB100 is Not advised for the Tsunami 2 or the Econami - BUT it is needed for Tsunami 1 and earlier Soundtraxx decoders or any other sound decoder. Gerry

See below: These two error messages are spurious and occur if you have the NCE Command Monitor open. This has been fixed in the V4.11.x series. This message tells me the command station didn't reply

An antivirus program has prevented the LaunchJMRI.exe file from being installed, because it is new! You'll have to temporarily turn off protection, or tell your antivirus software to accept

Gerry, I've been using the PTB100 for the past 3 years and it has worked?fine?up until now.? A problem exits using the Soundtraxx "Sound Decoder". Don't I need the PTB100 on all sound decoder

Hi Marc, I don't have the PR3 installed nor as part of my setup.? What I have is shown below: + Computer make and model - HP Compaq 6220 + Computer Operating System - Windows 7 + JMRI version

Mike, Please be VERY detailed in describing the problem you are experiencing. I find myself scratching my head trying to figure out what you mean by "this prevents me from being able to re-select the

I have beenhaving a problem with JMRI locking up during operating sessions.? A dispatcher panel using Panel Pro (version 4.10+R419243ewith version 1.8.0 for Java) is used to throw mainline switches

You may have hit a slots full issue, why stopepd at 15. Which command station are you using? you must make sure functions 0-8 are OFF when dispatching an engine to get it completly dispatched out of a

You could also add the 'cross to wrong side' switch to all the signal mast logic, so it musty be closed (normal running) for each check. if it's thrown, things drop through to red [jmriusers]

Hi Steve, Thanks for your help, that was my problem I still had one section in the transit in the reverse direction. It was until you said to check that all directions go the same way and then saw the

OK, sorry I was not aware of that. The Version upgrading of the JMRI error message is: Error Opening file for writing: C:&#92;program files (x86)&#92;JMRI&#92;LaunchJMRI.exe The error message in the

Has anyone used the AC_Powercontrol.py script in the jython folder? I have a Smart socket that I'd like to use to control power to the entire layout (command station, etc). I can currently control the