开云体育

P.J.: Was this a clean install of 4.8.0 (4.9.1?)? I've never seen a decoder go away but the JMRI will know that better than I. If you brought over older version of JMRI or the data from the old

We need more specific information about which decoders appear to be missing. There could also be a problem if your friend has been adding custom or prerelease definitions. In this case an

There are some issues here: - ESU decoders also need CV15/16 locking enabled (bit 1 of CV 124). - TCS decoders treat CV15=0 as a "universal unlock key" for a decoder, irrespective of the value in

Hi Randall It's obvious when you think about it, isn't it! I had set them both to 12080 assuming they should be the same - but they're obviously not! Changed the web server port to 12090 and it works!

Initially, both decoders received power from all pick-ups. But this problem occurred so I disconnected them. This gave me the added benefit of programming one decoder at a time in case the lock didn't

System is Windows 7 using JMRI 4.8 though I am not sure the JMRI version matters. Using a DCS240. Connection from PC through locobuffer to the 240. JMRI only finds 2 of the 5 UR92s on the layout.

Pcgumshoe, I would think there are several issues here. If you have front pickups going to front decoder only and likewise for the rear, then if you have track issues, only one decoder is getting

Ken, Unless I reported otherwise, the switches I listed were "non-shorting" switches. But if you are using a 30-degree-indexed switch for a 60-degree-indexing or a 90-degree-indexing application, then

A friend of mine just got a new computer. He is having two problems. First we set everything up for his Panel Pro. But when it comes up all the switches come up with the Unknown Icon. How do we get it

Paul; the command station is still showing disconnected the command station version and type is unknown my Mac is a late iMac 2015; it still takes time before I can even just read the system console

In your Preferences, I would expect WiThrottle tab to show port 12080 (based on your description). The Web Server port is something else, shown in Preferences under the Web Server tab. In the browser,

Uh Mark, where do you think Radio Shack got theirs? <g> Seth Neumann Mountain View, CA Sent from my iPhone, please excuse the typing.

Billybob, Nice bit of research. However, for any of the circuits I’ve seen for CTC panels, you always want break before make types. Next is ?” shaft vs 6mm shaft is less than a 1/64”

Dale, Here's my results from about 45 minutes work at the Mouser web site, looking only at "Alpha" rotary switches, and double-checking the part number versus the manufacturer's description. I

Can anyone help? JMRI runs OK on a Windows 10 PC. I can control throttles, turnouts and I have a working panel. Using Engine Driver on an Android 4.4 tablet, it connects OK to 192.168.2.2:12080 and I

Hello, I have an Athearn DDA40X non-sound unit that I purchased new. I didn't buy the sound version because I prefer the loksound select/direct decoders. My primary decoder is a Loksound Direct with

Great, thanks. I, too, bought a bunch of cheap Chinese ones and they wernt any better quality than the ones I got at the local Radio Shack when it closed. [jmriusers] wrote:

Mark, could you please provide the correct part numbers for the switches you referenced? You have shown the same part number for 3 different switches. Thanks, Dale Gloer

Andy, The CTCParts.com web site has an introduction to CTC - see http://www.ctcparts.com/about.htm http://www.ctcparts.com/about.htm . Specifically, "Part 5: The Control Machine", at the bottom of the

Hi all, any news on this topic, JMRI PanelPro - Programming Support for M?rklin CS2 / Doehler&Haass Programmer Regards, Moritz