¿ªÔÆÌåÓýTry to release the JMRI throttle before auto run the warrant. Daniel On 2024-10-02 01:51, Keith Williams
wrote:
|
|
|
Yes with a JMRI throttle to do the original?"learn mode", then when I go to auto run, i get this message.... On Tue, Oct 1, 2024 at 7:03?PM danielb987 via <jmri=[email protected]> wrote:
|
|
¿ªÔÆÌåÓýKeith, Are you running any train manually with a JMRI throttle or using an app, like WiThrottle or Engine Driver? Daniel On 2024-10-01 20:48, Keith Williams
wrote:
|
|
|
Ken, The second try worked. There are a few more changes. I recommend that the turnout speeds be adjusted. ?The default speed for Thrown is Restricted. ?I normally used Medium. This is set using the "Speeds -> Defaults" menu item in the Turnout table. This affects the signal mast logic when routes include thrown turnouts. The "LT1" turnout table entry currently has "Inverted" enabled. ?I suspect that this was an attempt to make the diverging leg of LT1 to be the normal route. ?I don't use inverted. ?My rule is that if the JMRI Closed state is not the preferred route, the switch machine wiring is changed. The image for LT1 has the wrong color (red). ?Right click LT1 and select Edit. ?Click on the "Create/Edit" block button. ?Set "Occupied Sense" to Active. If the problem is with what LS57 is reporting, fix it instead of masking the problem using JMRI.? The signal mast icons for LT01(B) and LT01(C) need to be flipped. LT14 signal masts: ?LT14(C) is missing and LT14(B) is in the wrong location on the panel. ?Enable "Right Hand Side" for all 3 locations and click on Done. ?This will add/move the masts to the proper locations. LT22 signal masts: ?Select LT22(C) for the 815 - 512 block boundary. ?Create SML for LT22(C). ?Delete and create SML for LT25(A). LT23 signal masts: ?Add the masts to the panel. ------------------------------------ The LT26/LT14 and LT23/LT27 turnout pairs look like crossovers. ?If they behave as crossovers then trains will never stop between the turnouts. ?If that is true, then blocks 833 and 816 are not needed. ?And signal masts LT26(C) and LT14(B) are not needed. ------------------------------------ There is an error where occupancy sensor LS400 assigned to blocks 804 and 810. ------------------------------------ Note: ?The middle loop ( P14, etc.) has an interesting problem that will require more research. ?When the turnouts are lined for the loop, a SML loop occurs. ?When a signal mast aspect changes, the previous mast has to determine if its aspect needs to change. ?If so, it changes and when triggers the next previous mast. ?The method for propagating changes can go forever. I think the problem is the number of signal masts in the loop. ?The outer loop does not have the problem. Dave Sand ----- Original message ----- From: Ken Fordham <j.kenneth.fordman@...> Subject: Re: [jmriusers] SML signal mast problem #sml Date: Tuesday, October 01, 2024 6:35 AM Good morning Let me try again. I made all the changes you recommended so I don't know what happened. |
|
|
Locked
Re: ANIMATED GIFS FOR SIGNAL HEADS
Vic,
yes, I did it about two years ago, using a free software on my MacBook Air.
?
The icons (flashing aspect) were included in FS-1987 Signal System. How may I help you?
?
Best regards from Tuscany?
?
Pino
?
? |
|
|
Locked
Re: OperationsPro - Location Schedules and "Count"
#operationspro
On Mon, Sep 30, 2024 at 07:14 PM, Dan Boudreau wrote:
For example, on Monday, the program will wait for 12 Hopper Iron cars to be delivered.? If only 11 arrive on Monday, the program will not move to the next deliver of 8 Hopper Coke on Tuesday. So in this case, am I understanding that the schedule will not move to the next line until the next Monday when the remaining Hopper Iron car is delivered?
--
Tom |
|
|
Locked
Re: Dispatcher Scripting support
#dispatcher
#scripting
Hi Dave,
?
Yes I want to allocate the next section early exactly the same way it can be done with the user interface bellow but within a script.
?
The sequence would be : (1) The train enters a section, (2) the dispatchers auto allocates to next safe section, (3) the first next section to that safe section is requested and pending for dispatch, (works fine until there), (4) the script can if some custom conditions are met, allocate that next section. All this according to the transit, no need to add any section to it.
Thanks Adrien
|
|
|
Locked
Re: Screenshot of JMRI
It works. thanks. JeanLouisDelestre@... De: "John Griffin" <johng.sst@...> ?: [email protected] ·¡²Ô±¹´Ç²â¨¦: Lundi 30 Septembre 2024 19:59:57 Objet: Re: [jmriusers] Screenshot of JRMI There is a free utility called ShareX that is excellent in clipping any section of the screen. It's what I use to capture?figures for my blog. It even captures drop downs. On Mon, Sep 30, 2024 at 9:06?AM splasher via <steve=[email protected]> wrote:
--
John Griffin Model Railroading Topics |
|
Giuseppe Di Biasi
Tom Myrick