[email protected]

Too convoluted.

Best is to upgrade to 4.18? or to the TEST version 4.19.5? as the LokPilot 5 has just been added to it.

Marc

ESU Loksound v5 Decoder Definition

#173078

Is it possible to add an ESU Loksound v5 and v5 micro decoder definition into an older version of JMRI (4.7.2 R471b21f) ?

Re: NEW USER

#173077

I forgot to add I'm running Beta 4.19.5 with Win10 updated and Java 1.8.0_251-b08

--
Alain355

Re: NEW USER

#173076

Hi Marc and Peter

I've seen this same error (no roster shown, even if the roster.xml file is there in the directory) sometime when switching from my simulator config (DCC being None) to my ECoS config, both using the same folder for my roster (2 roster groups, one being the full fleet, the other one being a substract of the 1st one).? The problem happened only when using the ECoS config after a session with Simulation, not while staying with the same config, nor using Simulation after a previous session with ECoS.

The bypass I found is similar to yours: I took the 2 following actions from the menu:
1) Rebuild Roster, result being no roster entries shown, but the 2 roster groups being there,
2) Update decoder definitions, result being OK, every entry was there OK, no need to restart JMRI

I tried yesterday to recreate it wo success. I'm wondering if it didn't happened each time (each month) I updated JMRI.

Alain355 in Paris
--
Alain355

Re: Classification yards #operationspro

#173075

开云体育

Phil

I assume when i read this statement that if i create train 1 using route 1 that i cant pickup the car with train 2 using route 1 because the program will see that the route is the same. ? Statement in manual specifically says ?“the same route”.

Are you saying that the program will allow train 2 to pickup the car dropped off by train 1 because the train name is different?

For the program to not pickup a car it must somehow mark the car to be not picked up by the train that left it. Is there a way to check which cars in my classification yard are so restricted as i do use the same train name with the same route name over and over.?

Tony

Show quoted text

On May 8, 2020, at 10:11 AM, Phil in gorgeous Young Harris via groups.io <philabernathy@...> wrote:

?On Thu, May 7, 2020 at 07:08 AM, AD wrote:

the manual indicates that a train with the same route cant re-use cars it delivered.?
Tony, just create another Train does has the same Route and alternate them.

Phil

Re: NEW USER

[email protected]

#173074

I see nothing indicating an error with the JMRI ROSTER.
I believe you (or JMRI) are pulling the engine database from the ECOS? which are the messages seen in the log (three times).

there is a reported bug in JMRI that causes the ROSTER to not show up. I am seeing this today in my JMRI Install? of 4.18.? I restart JMRI DecoderPro several times with no Roster presented (thow one exists).

There are no messages regarding the error condition in the System Console.

To fix this today I had to go to ACTIONS, Recreate Roster Index.?? Try this on your install.

Marc

Re: NX Routes? LRoutes? other? #entryexit

#173073

I use the hooks in Logix now to generate a signal request based on extant NX routes.?

Question: when an NX pair activated by a conditional, is that a "hard" activation (route comes in come hell or high water) - or is it the same as the user selecting Entry-Exit, subject to the same checks before activating the route?

My guess is it would be the latter scenario.

I will look at the python script. A dozen years back I programmed a whole interlocking in python starting with the "siglet.py" as an example.

Thanks,
Dave

Re: Auto running/dispatcher

#173072

Iain,

Automatic trains with signal heads/SSL require direction sensors the the SSL.

When a train is created, the direction sensors will be automatically added to the SSL if necessary.  In your sample panel, a mixture of forward and reverse sensors are being added.  When the train is created, only the forward sensors are set to Inactive which means the signal heads still show red.

I don't know the reason for the sensor issue.  It could be a bug or your sample panel is too simple.

You might try doing a simple 3 section without a turnout.  Or add a second turnout so that you end up with a siding and another set of signal heads.  Or use signal masts and signal mast logic instead of signal heads with SSL.  This removes the direction sensor requirement.

Dave Sand

Show quoted text

----- Original message -----
From: "Iain Burr via groups.io" <iain.burr@...>
To: [email protected]
Subject: Re: [jmriusers] Auto running/dispatcher
Date: Thursday, May 07, 2020 3:29 PM

Hello

I have changed the anchors to end bumpers then tried dispatcher again.  When I create a new item in dispatcher all the signals in the layout panel go red.  I have checked them and I think they are correct.  I will load up the panel if you would like to have a look.

Kind regards

Iain
Aberdeen Model Railway Club Member
On 7 May 2020, at 8:21 pm, Iain Burr via groups.io <iain.burr@...> wrote:

?Steve, Dave

Many thanks, I will try that out

Kind regards

Iain
Aberdeen Model Railway Club Member
On 7 May 2020, at 7:42 pm, Dave Sand <ds@...> wrote:

?Steve, Iain,

You can also just right click the anchor point at the end and change it to an end bumper.

Dave Sand

----- Original message -----
From: Steve_G <RailRodder@...>
To: jmriusers <[email protected]>
Subject: Re: [jmriusers] Auto running/dispatcher
Date: Thursday, May 07, 2020 12:27 PM

Hi Iain
THe end of the track needs to be an "End Bumper" not an "Anchor point". Just add
an end bumber, a piece of track between the anchor and the end, click the join
between the two and merge. Or delete the anchor, the track, add the end put back
the track, set up the block..
Steve G.

---------- Original Message ----------
From: "Iain Burr via groups.io" <iain.burr@...>
Date: May 7, 2020 at 1:03 PM

Thank you Steve

I have updated the signal heads. I get warning messages:

Cannot set up logic because the next Signal (in or at the end of block 70-3)
apparently is not yet defined

Same for 70-4 and 70-1 as well

Loco still does not start itself in dispatcher. If I use the AutoTrains tab
that comes up with dispatcher and go manual train will move and will stop
itself in block 3.

Kind regards

Iain
Aberdeen Model Railway Club Member
On 7 May 2020, at 4:41 pm, Steve_G <RailRodder@...> wrote:?Hi Iain
You are trying, by the looks of it, to use SignalHeads (Simple Systems
Logic). To do that, remove the xisting heads from the panel, then you need
to add the heads to either a block boundry or a Switch. Your heads dont
appear to be linked to either. To add then to the switch right click on the
Switch (not a boundry, the switch) and "set signal heads". Youll need 4
signals, 2 at the throut, and one each on the diverginging/continuing. See
if that gets you any further.
Steve G.

Re: Displaying the "Alternative Track Colour" when using Logix (or Lroute or anything else that works) #layouteditor #logix

#173071

I finally saw your answer in the #NX topic.? I'll follow that up.? Thank you again ...............

Re: Displaying the "Alternative Track Colour" when using Logix (or Lroute or anything else that works) #layouteditor #logix

#173070

Iain,

The ManageBlocks.py script in the JMRI install directory will do what you want. ?There is another version which has additional features. ?It used to be in the group's file area, but is no longer there. ?There are also internal JMRI changes which require script changes so newer versions will be coming soon.

Dave Sand

Show quoted text

----- Original message -----

From: Iain <iain@...>

To:?[email protected]

Subject: [jmriusers] Displaying the "Alternative Track Colour" when using Logix (or Lroute or anything else that works)

Date: Friday, May 08, 2020 3:41 AM

Some may remember my name from a while back when I was trying to get started and having the usual difficulties.? Many of you were very helpful, and indeed without your help I wouldn't have the working system that I have now.? The main help came from Dave Sand - but I have thanked him separately.? To those who helped thanks.

My control system has worked well and run my small UK layout well.? It's fully interlocked, BUT I chickened out on block occupancy.? It would probably have been the final straw back than anyway.? Now I am going to have a go.

I would LIKE to mimic the UK approach of having the track dark grey and marking a selected route through it in white.? The occupancy would show up red and clear to dark grey after clearance.? The switching to red on a sensor is easy enough (and I already do this manually) but the white route is different. There IS an alternative colour for the track and both Entry/Exit NX facilities and Dispatcher:

NX: "The full interlock will also set the state of the layout Blocks to use the alternative color, and the NX sensor buttons will remain in a solid active state".
Dispatcher: "Check Use alternate color for allocated Blocks to use the Layout Editor alternate unoccupied color for allocated Blocks in Layout Editor panels. This option is designed to make it easier for the dispatcher to see which Sections have been allocated."

Sadly neither NX or Dispatcher are suitable for my use.

I am sorry, but I have searched and searched but can find no way to cause this colour change in Logix.? I am happy to use other facilities or even Scripting if I must.? Can anybody please tell me how?

Re: How to get decoder pro to work on an imac running OS catalina, a Locobuffer-USB and a digitrax DCS51 command station #mac-os #digitrax #locobuffer-usb

#173069

I'm able to run JMRI on a Mac running OS 10.15.4 and an RR-Circuits LocoBuffer-USB. ?I don't know if this will work for you, but I found that I did NOT need to install the drivers recommended for LocoBuffer. ?The system just recognized the device when it was plugged in and all was well from there. ?I did try installing the extensions as the documentation suggested, but then it wouldn't work. ?So I uninstalled them and it's working again (with a reboot in between to ensure they weren't still running) Strange, but since it was working I stuck with it. ?

Your milage may vary of course.

Good luck,
Rich

Re: Classification yards #operationspro

#173068

On Thu, May 7, 2020 at 07:08 AM, AD wrote:

the manual indicates that a train with the same route cant re-use cars it delivered.?

Tony, just create another Train does has the same Route and alternate them.

Phil

Re: Layout Editor help - track occupancy color change only works with grid displayed

#173067

Andy,

AnyRail version 6.29 has the fix for the JMRI export that includes flex track.

Dave Sand

?

Show quoted text

----- Original message -----

From: LMSFAN72 <andrew@...>

To:?[email protected]

Subject: Re: [jmriusers] Layout Editor help - track occupancy color change only works with grid displayed

Date: Wednesday, April 29, 2020 5:04 PM

Thanks Dave, good to know the cause. I’m mostly through fixing everything now....... Best , Andy

Re: NEW USER

#173066

Thanks Marc,

System Console Log:

2020-05-08 23:26:36,565 util.Log4JUtil? ? ? ? ? ? ? ? ? ? ? ? INFO? - * JMRI log ** [main]

2020-05-08 23:26:36,594 util.Log4JUtil? ? ? ? ? ? ? ? ? ? ? ? INFO? - This log is appended to file: C:\Users\pete\JMRI\log\messages.log [main]

2020-05-08 23:26:36,594 util.Log4JUtil? ? ? ? ? ? ? ? ? ? ? ? INFO? - This log is stored in file: C:\Users\pete\JMRI\log\session.log [main]

2020-05-08 23:26:36,599 apps.AppsBase? ? ? ? ? ? ? ? ? ? ? ? ?INFO? - DecoderPro version 4.18+R37ad3d0 starts under Java 1.8.0_251 on Windows 10 x86 v10.0 at Fri May 08 23:26:36 AEST 2020 [main]

2020-05-08 23:26:36,785 gui3.Apps3? ? ? ? ? ? ? ? ? ? ? ? ? ? INFO? - Starting with profile My_JMRI_Railroad.3ded32fe [main]

2020-05-08 23:26:37,091 node.NodeIdentity? ? ? ? ? ? ? ? ? ? ?INFO? - Using 55c80d69-a115-4f2d-a220-868b7dfb7291 as the JMRI storage identity for profile id 3ded32fe [AWT-EventQueue-0]

2020-05-08 23:26:37,964 util.FileUtilSupport? ? ? ? ? ? ? ? ? INFO? - File path program: is C:\Program Files (x86)\JMRI\ [main]

2020-05-08 23:26:39,003 util.FileUtilSupport? ? ? ? ? ? ? ? ? INFO? - File path preference: is C:\Users\pete\JMRI\My_JMRI_Railroad.jmri\ [main]

2020-05-08 23:26:39,003 util.FileUtilSupport? ? ? ? ? ? ? ? ? INFO? - File path profile: is C:\Users\pete\JMRI\My_JMRI_Railroad.jmri\ [main]

2020-05-08 23:26:39,004 util.FileUtilSupport? ? ? ? ? ? ? ? ? INFO? - File path settings: is C:\Users\pete\JMRI\ [main]

2020-05-08 23:26:39,004 util.FileUtilSupport? ? ? ? ? ? ? ? ? INFO? - File path home: is C:\Users\pete\ [main]

2020-05-08 23:26:39,004 util.FileUtilSupport? ? ? ? ? ? ? ? ? INFO? - File path scripts: is C:\Program Files (x86)\JMRI\jython\ [main]

2020-05-08 23:26:41,537 ecos.EcosReply? ? ? ? ? ? ? ? ? ? ? ? ERROR - Trying to get message end code before message is complete [AWT-EventQueue-0]

2020-05-08 23:26:41,580 jmrix.AbstractMRTrafficController? ? ?WARN? - notify: During reply dispatch to jmri.jmrix.ecos.EcosSensorManager@1a4c865 [AWT-EventQueue-0]

java.lang.NumberFormatException: For input string: "30] protocol[DCC28]

1214 name["E 33 - 19 OeBB"] addr[332] protocol[DCC28]

1211 name["VT 137 - 044 DRG"] addr[220] protocol[DCC28]

1217 name["ET 87 - 03a DB"] addr[340] protocol[DCC28]

1219 name["DRG - E 75 - 53"] addr[341] protocol[DCC28]

1218 name["70 - 6068 KBStB"] addr[18] protocol[DCC28]

1221 name["DRG - E 04 - 02"] addr[343] protocol[DCC28]

1222 name["E 91 - 90 DRG"] addr[347] protocol[DCC28]

1197 name["DRG - E 19 - 11"] addr[344] protocol[DCC28]

1224 name["ET 87 - 03b DB"] addr[345] protocol[DCC28]

1223 name["EG 2x2/2 KBStB"] addr[346] protocol[DCC28]

1225 name["ET 85 LIGHTS"] addr[3301] protocol[DCC14]

1226 name["96 - 5751 KBStB"] addr[26] protocol[DCC28]

1228 name["roco 337v347 ???"] addr[337] protocol[DCC28]

1227 name["EP 3/6 - 20103"] addr[348] protocol[DCC28]

1220 name["78 - 510 DRG"] addr[147] protocol[DCC28]

1230 name["38 - 3346 DB"] addr[148] protocol[DCC28]

1229 name["94 - 8120 KPEV"] addr[149] protocol[DCC28]

1149 name["77 - 002 DRG"] addr[129] protocol[DCC28]

1079 name["86 - 842.2 DB"] addr[73] protocol[DCC28]

1231 name["??BB - 1116 ??FB"] addr[349] protocol[DCC28]

1232 name["94 - E1 - GBAG"] addr[30] protocol[DCC28]

1234 name["05 - 001 DRG"] addr[38] protocol[DCC28]

1070 name["38 - 2609 DRG"] addr[78] protocol[DCC28]

1103 name["03 - 111 DB"] addr[120] protocol[DCC28]

1002 name["86 - 739 DB"] addr[110] protocol[DCC28]

1141 name["13 - 639 KPEV"] addr[91] protocol[DCC28]

1143 name["38 - 2510 KPEV"] addr[124] protocol[DCC28]

1069 name["41 - 352 DB"] addr[76] protocol[DCC28]

1086 name["91 - 7338 #2 ?"] addr[136] protocol[DCC28]

1038 name["05 - 003 DRG"] addr[122] protocol[DCC28]

1184 name["22 - 012 DRG"] addr[150] protocol[DCC28]

1106 name["TRAXX 2"] addr[351] protocol[DCC28]

1092 name["175J Dosto "] addr[402] protocol[DCC14]

1123 name["DB Reg - Plochin"] addr[342] protocol[DCC28]

1153 name["DB Reg - Stutgar"] addr[353] protocol[DCC28]

1055 name["01 - 1090 DRG"] addr[121] protocol[DCC28]

1179 name["08 - 1001 DRG"] addr[140] protocol[DCC28]

1139 name["ET 85 - 09 DB"] addr[352] protocol[DCC28]

1233 name["03 - 1047 DRG"] addr[62] protocol[DCC28]

1237 name["03 - 1001 DRG"] addr[21] protocol[DCC28]

1239 name["ICE 4"] addr[356] protocol[DCC28]

1244 name["DB Car - 150-111"] addr[357] protocol[DCC28]

1245 name["??BB - 1142-642."] addr[358] protocol[DCC28]

1243 name["LAE - 111 - Fman"] addr[363] protocol[DCC28]

1249 name["SBB Cargo - 620"] addr[364] protocol[DCC28]

1250 name["SBB Cargo 620-1"] addr[364] protocol[DCC28]

1251 name["SBB Cargo 420.1"] addr[365] protocol[DCC28]

1238 name["22 - 01x DRG"] addr[151] protocol[DCC28]

1242 name["03 - 161 DRG"] addr[152] protocol[DCC28]

1082 name["39 - 158 DB"] addr[89] protocol[DCC28]

1246 name["38 - S10 KPEV"] addr[123] protocol[DCC28]

1241 name["38 - 1107 KPEV"] addr[153] protocol[DCC28]

1235 name["PIKO ANALYST"] addr[127] protocol[MM14]

1252 name["03 - 132 DB"] addr[154] protocol[DCC28]

1248 name["61 - 001 ""HW"""] addr[144] protocol[DCC28]

1247 name["Pt2/3-6068 KBSB"] addr[80] protocol[DCC28]

1236 name["S-Bahn 420 - DB"] addr[366] protocol[DCC28]

1175 name["V 220 - 022 DB"] addr[223] protocol[DCC28]

1254 name["V 200 - 009 DB"] addr[224] protocol[DCC28]

1255 name["VT 644 - 561 DB"] addr[225] protocol[DCC28]

1256 name["LINT - Syntas NS"] addr[226] protocol[DCC28]

1042 name["91 - 7316 KPEV"] addr[19] protocol[DCC28]

1174 name["78 - 1001 DRG"] addr[61] protocol[DCC28]

1240 name["ICE 1 - 0773 DB"] addr[325] protocol[DCC28]

1169 name["TEE - Helvetia"] addr[228] protocol[DCC28]

1258 name["ET 87 - 03c DB"] addr[367] protocol[DCC28]

1257 name["LokPilot V4.0"] addr[250] protocol[DCC28]

1259 name["ET 85 - 485 DB"] addr[368] protocol[DCC28]

1260 name["K??f II"] addr[229] protocol[DCC28]

1261 name["KOF"] addr[230] protocol[DCC28]

1262 name["New "

at java.lang.NumberFormatException.forInputString(Unknown Source)

at java.lang.Integer.parseInt(Unknown Source)

at jmri.jmrix.ecos.EcosReply.getEcosObjectId(EcosReply.java:236)

at jmri.jmrix.ecos.EcosSensorManager.reply(EcosSensorManager.java:64)

at jmri.jmrix.ecos.EcosTrafficController.forwardReply(EcosTrafficController.java:74)

at jmri.jmrix.AbstractMRTrafficController.notifyReply(AbstractMRTrafficController.java:284)

at jmri.jmrix.AbstractMRTrafficController$RcvNotifier.run(AbstractMRTrafficController.java:1226)

at java.awt.event.InvocationEvent.dispatch(Unknown Source)

at java.awt.EventQueue.dispatchEventImpl(Unknown Source)

at java.awt.EventQueue.access$500(Unknown Source)

at java.awt.EventQueue$3.run(Unknown Source)

at java.security.AccessController.doPrivileged(Native Method)

at java.security.ProtectionDomain$JavaSecurityAccessImpl.doIntersectionPrivilege(Unknown Source)

at java.awt.EventQueue.dispatchEvent(Unknown Source)

at java.awt.EventDispatchThread.pumpOneEventForFilters(Unknown Source)

at java.awt.EventDispatchThread.pumpEventsForFilter(Unknown Source)

at java.awt.EventDispatchThread.pumpEventsForHierarchy(Unknown Source)

at java.awt.EventDispatchThread.pumpEvents(Unknown Source)

at java.awt.EventDispatchThread.run(Unknown Source)

2020-05-08 23:26:41,583 jmrix.AbstractMRTrafficController? ? ?WARN? - notify: During reply dispatch to jmri.jmrix.ecos.EcosLocoAddressManager@9f66ed [AWT-EventQueue-0]

java.lang.NumberFormatException: For input string: "30] protocol[DCC28]

1214 name["E 33 - 19 OeBB"] addr[332] protocol[DCC28]

1211 name["VT 137 - 044 DRG"] addr[220] protocol[DCC28]

1217 name["ET 87 - 03a DB"] addr[340] protocol[DCC28]

1219 name["DRG - E 75 - 53"] addr[341] protocol[DCC28]

1218 name["70 - 6068 KBStB"] addr[18] protocol[DCC28]

1221 name["DRG - E 04 - 02"] addr[343] protocol[DCC28]

1222 name["E 91 - 90 DRG"] addr[347] protocol[DCC28]

1197 name["DRG - E 19 - 11"] addr[344] protocol[DCC28]

1224 name["ET 87 - 03b DB"] addr[345] protocol[DCC28]

1223 name["EG 2x2/2 KBStB"] addr[346] protocol[DCC28]

1225 name["ET 85 LIGHTS"] addr[3301] protocol[DCC14]

1226 name["96 - 5751 KBStB"] addr[26] protocol[DCC28]

1228 name["roco 337v347 ???"] addr[337] protocol[DCC28]

1227 name["EP 3/6 - 20103"] addr[348] protocol[DCC28]

1220 name["78 - 510 DRG"] addr[147] protocol[DCC28]

1230 name["38 - 3346 DB"] addr[148] protocol[DCC28]

1229 name["94 - 8120 KPEV"] addr[149] protocol[DCC28]

1149 name["77 - 002 DRG"] addr[129] protocol[DCC28]

1079 name["86 - 842.2 DB"] addr[73] protocol[DCC28]

1231 name["??BB - 1116 ??FB"] addr[349] protocol[DCC28]

1232 name["94 - E1 - GBAG"] addr[30] protocol[DCC28]

1234 name["05 - 001 DRG"] addr[38] protocol[DCC28]

1070 name["38 - 2609 DRG"] addr[78] protocol[DCC28]

1103 name["03 - 111 DB"] addr[120] protocol[DCC28]

1002 name["86 - 739 DB"] addr[110] protocol[DCC28]

1141 name["13 - 639 KPEV"] addr[91] protocol[DCC28]

1143 name["38 - 2510 KPEV"] addr[124] protocol[DCC28]

1069 name["41 - 352 DB"] addr[76] protocol[DCC28]

1086 name["91 - 7338 #2 ?"] addr[136] protocol[DCC28]

1038 name["05 - 003 DRG"] addr[122] protocol[DCC28]

1184 name["22 - 012 DRG"] addr[150] protocol[DCC28]

1106 name["TRAXX 2"] addr[351] protocol[DCC28]

1092 name["175J Dosto "] addr[402] protocol[DCC14]

1123 name["DB Reg - Plochin"] addr[342] protocol[DCC28]

1153 name["DB Reg - Stutgar"] addr[353] protocol[DCC28]

1055 name["01 - 1090 DRG"] addr[121] protocol[DCC28]

1179 name["08 - 1001 DRG"] addr[140] protocol[DCC28]

1139 name["ET 85 - 09 DB"] addr[352] protocol[DCC28]

1233 name["03 - 1047 DRG"] addr[62] protocol[DCC28]

1237 name["03 - 1001 DRG"] addr[21] protocol[DCC28]

1239 name["ICE 4"] addr[356] protocol[DCC28]

1244 name["DB Car - 150-111"] addr[357] protocol[DCC28]

1245 name["??BB - 1142-642."] addr[358] protocol[DCC28]

1243 name["LAE - 111 - Fman"] addr[363] protocol[DCC28]

1249 name["SBB Cargo - 620"] addr[364] protocol[DCC28]

1250 name["SBB Cargo 620-1"] addr[364] protocol[DCC28]

1251 name["SBB Cargo 420.1"] addr[365] protocol[DCC28]

1238 name["22 - 01x DRG"] addr[151] protocol[DCC28]

1242 name["03 - 161 DRG"] addr[152] protocol[DCC28]

1082 name["39 - 158 DB"] addr[89] protocol[DCC28]

1246 name["38 - S10 KPEV"] addr[123] protocol[DCC28]

1241 name["38 - 1107 KPEV"] addr[153] protocol[DCC28]

1235 name["PIKO ANALYST"] addr[127] protocol[MM14]

1252 name["03 - 132 DB"] addr[154] protocol[DCC28]

1248 name["61 - 001 ""HW"""] addr[144] protocol[DCC28]

1247 name["Pt2/3-6068 KBSB"] addr[80] protocol[DCC28]

1236 name["S-Bahn 420 - DB"] addr[366] protocol[DCC28]

1175 name["V 220 - 022 DB"] addr[223] protocol[DCC28]

1254 name["V 200 - 009 DB"] addr[224] protocol[DCC28]

1255 name["VT 644 - 561 DB"] addr[225] protocol[DCC28]

1256 name["LINT - Syntas NS"] addr[226] protocol[DCC28]

1042 name["91 - 7316 KPEV"] addr[19] protocol[DCC28]

1174 name["78 - 1001 DRG"] addr[61] protocol[DCC28]

1240 name["ICE 1 - 0773 DB"] addr[325] protocol[DCC28]

1169 name["TEE - Helvetia"] addr[228] protocol[DCC28]

1258 name["ET 87 - 03c DB"] addr[367] protocol[DCC28]

1257 name["LokPilot V4.0"] addr[250] protocol[DCC28]

1259 name["ET 85 - 485 DB"] addr[368] protocol[DCC28]

1260 name["K??f II"] addr[229] protocol[DCC28]

1261 name["KOF"] addr[230] protocol[DCC28]

1262 name["New "

at java.lang.NumberFormatException.forInputString(Unknown Source)

at java.lang.Integer.parseInt(Unknown Source)

at jmri.jmrix.ecos.EcosReply.getEcosObjectId(EcosReply.java:236)

at jmri.jmrix.ecos.EcosLocoAddressManager.reply(EcosLocoAddressManager.java:595)

at jmri.jmrix.ecos.EcosTrafficController.forwardReply(EcosTrafficController.java:74)

at jmri.jmrix.AbstractMRTrafficController.notifyReply(AbstractMRTrafficController.java:284)

at jmri.jmrix.AbstractMRTrafficController$RcvNotifier.run(AbstractMRTrafficController.java:1226)

at java.awt.event.InvocationEvent.dispatch(Unknown Source)

at java.awt.EventQueue.dispatchEventImpl(Unknown Source)

at java.awt.EventQueue.access$500(Unknown Source)

at java.awt.EventQueue$3.run(Unknown Source)

at java.security.AccessController.doPrivileged(Native Method)

at java.security.ProtectionDomain$JavaSecurityAccessImpl.doIntersectionPrivilege(Unknown Source)

at java.awt.EventQueue.dispatchEvent(Unknown Source)

at java.awt.EventDispatchThread.pumpOneEventForFilters(Unknown Source)

at java.awt.EventDispatchThread.pumpEventsForFilter(Unknown Source)

at java.awt.EventDispatchThread.pumpEventsForHierarchy(Unknown Source)

at java.awt.EventDispatchThread.pumpEvents(Unknown Source)

at java.awt.EventDispatchThread.run(Unknown Source)

2020-05-08 23:26:41,596 ptionhandler.UncaughtExceptionHandler ERROR - Uncaught Exception caught by jmri.util.exceptionhandler.UncaughtExceptionHandler [AWT-EventQueue-0]

java.lang.NumberFormatException: For input string: "30] protocol[DCC28]

1214 name["E 33 - 19 OeBB"] addr[332] protocol[DCC28]

1211 name["VT 137 - 044 DRG"] addr[220] protocol[DCC28]

1217 name["ET 87 - 03a DB"] addr[340] protocol[DCC28]

1219 name["DRG - E 75 - 53"] addr[341] protocol[DCC28]

1218 name["70 - 6068 KBStB"] addr[18] protocol[DCC28]

1221 name["DRG - E 04 - 02"] addr[343] protocol[DCC28]

1222 name["E 91 - 90 DRG"] addr[347] protocol[DCC28]

1197 name["DRG - E 19 - 11"] addr[344] protocol[DCC28]

1224 name["ET 87 - 03b DB"] addr[345] protocol[DCC28]

1223 name["EG 2x2/2 KBStB"] addr[346] protocol[DCC28]

1225 name["ET 85 LIGHTS"] addr[3301] protocol[DCC14]

1226 name["96 - 5751 KBStB"] addr[26] protocol[DCC28]

1228 name["roco 337v347 ???"] addr[337] protocol[DCC28]

1227 name["EP 3/6 - 20103"] addr[348] protocol[DCC28]

1220 name["78 - 510 DRG"] addr[147] protocol[DCC28]

1230 name["38 - 3346 DB"] addr[148] protocol[DCC28]

1229 name["94 - 8120 KPEV"] addr[149] protocol[DCC28]

1149 name["77 - 002 DRG"] addr[129] protocol[DCC28]

1079 name["86 - 842.2 DB"] addr[73] protocol[DCC28]

1231 name["??BB - 1116 ??FB"] addr[349] protocol[DCC28]

1232 name["94 - E1 - GBAG"] addr[30] protocol[DCC28]

1234 name["05 - 001 DRG"] addr[38] protocol[DCC28]

1070 name["38 - 2609 DRG"] addr[78] protocol[DCC28]

1103 name["03 - 111 DB"] addr[120] protocol[DCC28]

1002 name["86 - 739 DB"] addr[110] protocol[DCC28]

1141 name["13 - 639 KPEV"] addr[91] protocol[DCC28]

1143 name["38 - 2510 KPEV"] addr[124] protocol[DCC28]

1069 name["41 - 352 DB"] addr[76] protocol[DCC28]

1086 name["91 - 7338 #2 ?"] addr[136] protocol[DCC28]

1038 name["05 - 003 DRG"] addr[122] protocol[DCC28]

1184 name["22 - 012 DRG"] addr[150] protocol[DCC28]

1106 name["TRAXX 2"] addr[351] protocol[DCC28]

1092 name["175J Dosto "] addr[402] protocol[DCC14]

1123 name["DB Reg - Plochin"] addr[342] protocol[DCC28]

1153 name["DB Reg - Stutgar"] addr[353] protocol[DCC28]

1055 name["01 - 1090 DRG"] addr[121] protocol[DCC28]

1179 name["08 - 1001 DRG"] addr[140] protocol[DCC28]

1139 name["ET 85 - 09 DB"] addr[352] protocol[DCC28]

1233 name["03 - 1047 DRG"] addr[62] protocol[DCC28]

1237 name["03 - 1001 DRG"] addr[21] protocol[DCC28]

1239 name["ICE 4"] addr[356] protocol[DCC28]

1244 name["DB Car - 150-111"] addr[357] protocol[DCC28]

1245 name["??BB - 1142-642."] addr[358] protocol[DCC28]

1243 name["LAE - 111 - Fman"] addr[363] protocol[DCC28]

1249 name["SBB Cargo - 620"] addr[364] protocol[DCC28]

1250 name["SBB Cargo 620-1"] addr[364] protocol[DCC28]

1251 name["SBB Cargo 420.1"] addr[365] protocol[DCC28]

1238 name["22 - 01x DRG"] addr[151] protocol[DCC28]

1242 name["03 - 161 DRG"] addr[152] protocol[DCC28]

1082 name["39 - 158 DB"] addr[89] protocol[DCC28]

1246 name["38 - S10 KPEV"] addr[123] protocol[DCC28]

1241 name["38 - 1107 KPEV"] addr[153] protocol[DCC28]

1235 name["PIKO ANALYST"] addr[127] protocol[MM14]

1252 name["03 - 132 DB"] addr[154] protocol[DCC28]

1248 name["61 - 001 ""HW"""] addr[144] protocol[DCC28]

1247 name["Pt2/3-6068 KBSB"] addr[80] protocol[DCC28]

1236 name["S-Bahn 420 - DB"] addr[366] protocol[DCC28]

1175 name["V 220 - 022 DB"] addr[223] protocol[DCC28]

1254 name["V 200 - 009 DB"] addr[224] protocol[DCC28]

1255 name["VT 644 - 561 DB"] addr[225] protocol[DCC28]

1256 name["LINT - Syntas NS"] addr[226] protocol[DCC28]

1042 name["91 - 7316 KPEV"] addr[19] protocol[DCC28]

1174 name["78 - 1001 DRG"] addr[61] protocol[DCC28]

1240 name["ICE 1 - 0773 DB"] addr[325] protocol[DCC28]

1169 name["TEE - Helvetia"] addr[228] protocol[DCC28]

1258 name["ET 87 - 03c DB"] addr[367] protocol[DCC28]

1257 name["LokPilot V4.0"] addr[250] protocol[DCC28]

1259 name["ET 85 - 485 DB"] addr[368] protocol[DCC28]

1260 name["K??f II"] addr[229] protocol[DCC28]

1261 name["KOF"] addr[230] protocol[DCC28]

1262 name["New "

at java.lang.NumberFormatException.forInputString(Unknown Source)

at java.lang.Integer.parseInt(Unknown Source)

at jmri.jmrix.ecos.EcosReply.getEcosObjectId(EcosReply.java:236)

at jmri.jmrix.ecos.EcosTurnoutManager.reply(EcosTurnoutManager.java:95)

at jmri.jmrix.ecos.EcosTrafficController.forwardReply(EcosTrafficController.java:74)

at jmri.jmrix.AbstractMRTrafficController.notifyReply(AbstractMRTrafficController.java:295)

at jmri.jmrix.AbstractMRTrafficController$RcvNotifier.run(AbstractMRTrafficController.java:1226)

at java.awt.event.InvocationEvent.dispatch(Unknown Source)

at java.awt.EventQueue.dispatchEventImpl(Unknown Source)

at java.awt.EventQueue.access$500(Unknown Source)

at java.awt.EventQueue$3.run(Unknown Source)

at java.security.AccessController.doPrivileged(Native Method)

at java.security.ProtectionDomain$JavaSecurityAccessImpl.doIntersectionPrivilege(Unknown Source)

at java.awt.EventQueue.dispatchEvent(Unknown Source)

at java.awt.EventDispatchThread.pumpOneEventForFilters(Unknown Source)

at java.awt.EventDispatchThread.pumpEventsForFilter(Unknown Source)

at java.awt.EventDispatchThread.pumpEventsForHierarchy(Unknown Source)

at java.awt.EventDispatchThread.pumpEvents(Unknown Source)

at java.awt.EventDispatchThread.run(Unknown Source)

Locations Data:

User Files Location: C:\Users\pete\JMRI\My_JMRI_Railroad.jmri\

Roster Location: C:\Users\pete\JMRI\My_JMRI_Railroad.jmri\

Profile Location: C:\Users\pete\JMRI\My_JMRI_Railroad.jmri\

Settings Location: C:\Users\pete\JMRI\

Current Config file:C:\Users\pete\JMRI\My_JMRI_Railroad.jmri\ProfileConfig.xml

Scripts Location: C:\Program Files (x86)\JMRI\jython\

Program Location: C:\Program Files (x86)\JMRI

Temp Files Location:C:\Users\pete\AppData\Local\Temp\

Log Files Location: C:\Users\pete\JMRI\log\

? C:\Users\pete\JMRI\log\messages.log

? C:\Users\pete\JMRI\log\messages.log.1

? C:\Users\pete\JMRI\log\session.log

Peter

?

Re: Rather weird error cropping up

#173065

Hi Dave. It turned out that I was using 4.19.5ish Jenkinson build. I uninstalled it, re-installed from scratch and still had the same problem. Then installed JMRI.4.19.5+R6ede87265 and on starting it, the panels loaded perfectly. Thanks for your assistance. I think case closed.
Chris.

Re: How to get decoder pro to work on an imac running OS catalina, a Locobuffer-USB and a digitrax DCS51 command station #mac-os #digitrax #locobuffer-usb

#173064

Robert,

On 7 May 2020, at 10:49 PM, robertlambert via groups.io <robertlambert@...> wrote:

When I look under decoderpro/loconet/Monitor Locnet Stats/ there is no information (all fields blank), indicating
no comms connection (driver problem).

After searching the internet , the problem seems to be loading the drivers (not installing them).
I haver followed all the advice I can find on the internet on how to load the drivers, but I can not get it to work.

When I try to read a CV, I get the comms error message 306.As an aside to the driver problems, I don't know how you are even getting JMRI to launch if you can't get a driver to load. JMRI with Mac won't let you start up at all if your selected Port doesn't exist.

Please go to JMRI's Help->System Console menu item, use the Copy to Clipboard  button and paste into a post.

Dave in Australia

Re: How to get decoder pro to work on an imac running OS catalina, a Locobuffer-USB and a digitrax DCS51 command station #mac-os #digitrax #locobuffer-usb

#173063

Robert,

On 8 May 2020, at 7:20 PM, robertlambert via groups.io <robertlambert@...> wrote:

After running the looping command in Terminal, and plugging in the LocoBuffer-USB device, nothing changed,
no device names appeared.
I have attached a screenshot. You can't have attachments to posts. They are stripped by the list processor.

I have also attached a screenshot of the driver plist, i.e.
Library/Extensions/FTDIUSBSerialDriver.kext/plist showing the entry for LocoBuffer.You can't have attachments to posts. They are stripped by the list processor. If you've got the FTDI kext in /Library/Extensions that's good (what version?). Is there any FTDI item in  /System/Library/Extensions?

In System Preferences /Security and Privileges/ I can see no reference to the driver - this where I came unstuck before,
as I can not see any way to approve the driver.I don't have Catalina so I can't give you the details. But many of my fellow JMRI developers use Macs and some are using Catalina. Likewise I'm sure there are plenty of users with Catalina and FTDI devices.

I seem to remember having to approve drivers on El Capitan or Sierra but my memory isn't clear on this.

Hopefully someone can assist here....

(Also please update to the latest 4.19.x JMRI version. I seem to remember a baud rate issue with the LocoBuffer USB and a fairly recent JMRI version.)

Dave in Australia

Re: Use JMRI as Stationary Sound Decoder

#173062

@Klaus,? Thanks for that info and clarification, I had forgotten about that since it did not apply to my layout that doesn't have any blocking or?Advanced Location Following capability.??
--
-splasher in somd

Re: Route Table "Automatically Generate System Name" overwriting existing entries #4-18 #routes #mac-os #tables

SimonB

#173061

Just to finish up - this was successful. I ended up choosing MRC Simulator for the connection and then did a number of searches and replaces on the original xml to find and fix up the system names to match the correct 'Internal' connection pattern for turnouts (ITnn), routes (IR:AUTO:nnnn) and blocks (IB:AUTO:nnnn).

Thanks again for outlining so clearly the reason for the behaviour that was at the root of my issue, Dave.

Cheers
Simon

Fast Clock

#173060

I have my panel set up under Layout Editor and this is working correctly.

I have a clock on the panel which is "controlled" by a Logic Rail Technologies fast clock and this all works ok.

The clock was set on the panel in Edit Mode, going Options=>Add=>Add Fast Clock.

However there is no option for the type of clock. I would like the clock to be digital to match the LRT one.

I know that if, from the start page, I go to Tools=>Clocks I can choose a LCD clock, but this opens in a different window and, as far as I can see, does not form "part" of the panel.

So my question is "Is there a way of getting an LCD clock on the panel rather than in a different window"?

If not, could the option be available when in panel edit mode.

Thanks in advance for your help.

Brian Clark

Bedford UK.