开云体育

I'm using Team Digital detection boards and Signal Head Drivers(SHD) that are now being distributed by RRCirKits. I've used Digitrax boards in the past where all of the addresses for turnouts and

/g/jmriusers/files/CTC_Tutorial.jmri.zip -- Peter Ulvestad JMRI Users Group Moderator - https://www.jmri.org ( http://www.jmri.org ) Tam Valley Group Moderator -

I just discovered the “new” CTC tools… There are no screen shots included in the documentation at https://www.jmri.org/help/en/package/jmri/jmrit/ctc/CTC.shtml . Does anyone know of screen shots

Marc, If you "copy" an existing profile using Preferences >> Config Profiles, it will behave as you expect. For the majority of people, a single profile at the "settings:" location works fine, and it

Both CATS and Designer open as they should, however when I open CATS and try to open a saved file from Designer, the file will not open. The CATS panel stays blank. The shows the xml extension and it

Depending on which window you’re on, the choices are: - Store Panels… - Store -> Store Configuration And Panels to File … These two are the same. Note that they say _Panel_s_ plural. They store

Dave,? I do not disagree with you. I simply would like to know why the JMRI installer and setup does not follow your recommended structure. Newly created Profile : User Files Location: C:\Documents

If COM3 is in red then it is not a valid port or is disconnected and not available. I assume you did not import/copy old computer files to New !. Go into Device Manager and view the Port (Com & LPT)?

Ed, Your description of the symptoms sounds like a windows driver issue rather than a JMRI problem. Is it fair to believe that you have already checked that out? Cliff in Baja SoCal

Had older PC with Dec. Pro (4.10) prevoiusly working with this cable. Installed Dec. Pro (4.18) on a newer PC (WIN 10). ?Have fitted serial connection (serial to USB) to EasyDcc command station. This

http://www.quaker-valley.com/CTC/JMRI_Panel_Tutorial.html -- Peter Ulvestad JMRI Users Group Moderator - https://www.jmri.org ( http://www.jmri.org ) Tam Valley Group Moderator -

It realy doesn’t state but here is all that I have “JMRI Panel Tutorial -Part 2” R. Bucklew 07/25/15. I am currently running JMRI 4.19 on a Windows 10 tower . It also has a window

What tutorial are you referring to? -- Peter Ulvestad JMRI Users Group Moderator - https://www.jmri.org ( http://www.jmri.org ) Tam Valley Group Moderator - https://tamvalleydepot.com/ (

Hi, it's me again with yet another confusing to me question regarding saving panels. When doing so much requiring several panels or menus to be open at one time from where does one save? Some of these

In the Panel Tutorial -Part 2 I have been attempting to create my own panel. I am doing this on a separate computer as I already have a working panel on my layout. I am driven, though, to figure this

I have manually created the correct logic for the signal masts, but the issue seems to be that the paths are marked invalid, so the route never goes Active. I FINALLY got them all to respond

Sott, Based on your description, it seems the best solution is manually adjust the signal mast logic across the double cross-over. Some people have assigned 4 virtual blocks with virtual sensors to

Thanks Phil, but on this railroad the sidings are not all the same length and some are shorter than some of the trains. That's why it would be helpful for the DS to know the train length. Cheers,

Hi again Dan, The lineups I have worked with went something like this, but it's been over 35 years. Each train was on one line. OAEUY-05 ENGINE 8827 ON DUTY 0815 AM ENGINEER DRURY CONDUCTOR BOUDREAU

I have manually created the necessary logics for each of the four signals. The issue seems to be that JMRI thinks the paths are invalid. I have cleared the paths several times. Each time they seem to