Is this true of Engine Driver? If so, Steve Todd’s Raspberry Pi image is great for clubs where members bring their personal equipment!

I still think it has something to do with either a setting or the video drivers or something on that particular series of laptop. In my case when I couldn’t transfer the image using the laptop I went to my desktop and was able to successfully transfer the very same image file without a problem. This would seem to indicate that the image wasn’t the problem. I standardized the images (using PhotoShop) to a 300x500 .jpg after nothing else worked but still no joy. I blame the aliens.
--
Mike Heintzman
Modeling the P&PU since 1953

correction: It is a layout editor (LE) panel.

Chuck

The following issue appeared with installation of 4.18, was cleared by reverting back to 4.16:
Context: simple panel editor panel, turnouts have no feedback. There are 2 double crossovers, this problem only occurs with the second (higher TO#) instance. There is no issue with control of the individual turnouts that make up the double x-over when addressing them directly. Each double x-over on the panel uses both primary and secondary turnout assignments.
Problem: When activating the problem item on the panel. only the secondary unit switches. Reversing the assignments (making the pri into the sec and vis-vers), activation remains the assigned secondary turnout. If use of secondary is turned off, the correct single unit is activated. There is no problem with the first instance on the double x-over.

thanks,
Chuck

Following along, it seems at some point I'm going to need to write some of my own logic.

I learned Intel assembly language and QuickBASIC decades ago. But C and C++ stumped me. Is it realistic to think I can learn to program in Jython? My impression from bits in the messages here, is that it's "C like". I'm 75 years old, and it's harder for me to learn complex new things than it was...

Also, I have a mailing about "The Great Courses", and one of them is a 24 lesson course in Python I could order for $35. Might that be useful? Or, is there some programming manual I should buy? I don't want to ask a million beginner's questions on the list. But, what's a good way to learn to program in Jython?

Don Weigt
Connecticut, USA

David and Mick,

JMRI _intentionally_ changes track power status to "ON" at the end of a
programming sequence when programming in "Service" mode.

Further digging reveals that this code was specifically added in relation to
a user's issue. Further investigation revealed a DB150-specific requirement
to turn track power "ON" after programming operations for any programming
mode other than "ops-mode". See the Github issue # 983, and Bob Jacobsen's
comment dated March 5, 2016. ( )

Curiously, a comment in the code says "Internal routine to handle a
programming timeout by turning power off.", but the code turns track power
ON... There is no explanation why there is this discrepancy.

So far as I know, JMRI does not currently do anything specific with the
"command station" information configured for the connection. But this
specific example is one place where it might be sensible to do so... JMRI
could be sensitized to the "command station type" for the connection, and
only do this when a DB150 is specified.

Regards,
Billybob

Hi
I've just tried to alter the Bridge Decoration line width using Layout Editor. This defaults to 1 and I wanted to increase it slightly to 3. However the dialog indicates that value must be between 10 and 200, and prevents any other change! I don't think the panel contents are important, but a panel I've uploaded before has a bridge that can be edited: /g/jmriusers/files/ProblemsBeingWorkedOn/Andy%20Brown%20-%20161045/WebTrackDecorations01.xml

I successfully changed the xml to the value I wanted and it displayed as expected.

I've tried this in 4.18 and a later JMRI.4.19.2ish+jenkins+20200109T0259Z+R7f4b88d, both exhibit the same issue.

I'm running Ubunutu 19.10 with java 11.0.5 (en_GB)

A minor issue, but I thought I'd report it anyway.

Thanks
Andy

LH479 is not defined in SSL?

Inobu

Siglet start invoked for "LH497BlockBossLogic", but no inputs provided [AWT-EventQueue-0]


Inobu

Check LH497BlockBossLogic

That is the only error popping up.

Inobu

Frank,

I opened it,

Mountain Division Panel, Traffic center,Valley Division Bakersfield North End, Bakersfield South?

A lot of stuff, it seems to be.?

I opened it via Digitrax sim to avoid an equipment conflicts. You might want to try DIgitrax sim and troubleshoot backwards. You could have something hanging up a file. You have a lot going on. ?

Inobu

Hello,

I had a panel (three level) in JMRI.? I recently learned how to take sections of it and create separate panels for specific areas.? I did this, however those new separate panels show in the main panel group, but I cannot open them...and they appear blank.? Suggestions?

I posted the file in the files section and hopefully I did it right and you can open it!? CPRX 2017 Frank Kenny file.

Thanks for helping,
Frank
--

开云体育

That is what I was doing, but not working yet.

I am configuring a complex interlocking in Logix where I would like to delay signals "until the dust settles" after throwing turnouts. There are delayed actions for turnouts and sensors, but that seems to be it, nothing for heads or masts. I could also imagine such a feature would be useful as a timed lockout such as was used in 1:1 interlockings.

However, in the XML for the signal mast action there is a "delay=[x]" variable. As you can guess by now, messing around with it doesn't seem to do anything. Is it ignored?

Lacking a signal delay feature, any ideas for a workaround to do it?

? ...mike

Have you tried it with the new PR?

Must be tired, just realized you don't want the "Run Excel Switch List" option.

Dan

Hi Phil,

Try "Run Excel Switch List".

The help has the details.



Dan