开云体育

I'll give it a shot and report back.

JerryG: Thank you for reporting this. I'll be following up on the issue you filed with the JMRI project on GitHub. Randall

Bobby: It is JMRI's problem because JMRI should be able to handle the fact that JMRI produces long file names on the most common operating system JMRI supports and the most likely operating system

Hello Tony,?Not sure if this would work for you but,? why don't you go into the cars menu and use SET to put the caboose on the virtual track.?John? On Thu, Dec 19, 2019 at 2:02 AM,

Correction, 3 & 4 (or even 2 & 3 or 4 & 5). All (on any device) would cause communication failure. Dave in Australia

Andrew, What we know so far: All fine there. JMRI has asked the NCE USB for a Version Report (the AA command). The NCE USB has responded with "7.3.0". This tells us: - The JMRI baud rate setting of

One question: The trace you show doesn’t seem to have any inputs changing; the poll responses are all zero. Did you see a Sensor changing in JMRI? To debug this, I’d use that trace information

Test version 4.17.8 of JMRI/DecoderPro is available for download. This is the next in a series of test releases that will culminate in a JMRI 4.18 production release, hopefully in the next week or

Andrew, You don't have V1.65B. It would say so at startup. Dave in Australia

Don't know if I have 1.65B. ?How do I check that? ?At power up it just says 1.65. No resistors on PCP's, but I've tried the two, of very different ages. ?You'd think one would likely be

I moved the 4 wire cable to the PowerCab, and swapped in a new 6-wire btwn PCP and USB, and got the following error (not a 301, so cables okay, right?): 2019-12-18 23:24:04,070 util.Log4JUtil ? ?

Andrew, It may seem counterintuitive, but it would result in a very different error message (no timeout but instead a "301 no loco detected") if you had two good cables. Worth trying all possible

my feeling is that this cant be done but i thought i would ask in case someone has an idea. my caboose tracks are tracks 2 & 4 in my classification yard where all my cars are stored. i have a

Dave, Okay, it's not the cables; tried spare in all various combos and same thing happened each time. ?Well, actually, I never tried using the 4-wire cable to connect the PowerCab to the PCP, because

Andrew, Excellent. That means you must not touch JMRI, SiLabs drivers or NCE USB jumper settings. All those are ruled out. I'm assuming that the Cab Bus LED on the NCE USB only comes on (and stays

Here is the same thing tried with the cord plugged into the rear port of the PCP: 2019-12-18 19:34:50,767 util.Log4JUtil ? ? ? ? ? ? ? ? ? ? ? ?INFO ?- * JMRI log **

Thanks doc. ?Here it is: 2019-12-18 19:28:35,946 util.Log4JUtil ? ? ? ? ? ? ? ? ? ? ? ?INFO ?- * JMRI log ** [main] 2019-12-18 19:28:36,924 util.Log4JUtil ? ? ? ? ? ? ?

Have installed JMRI on a ‘new’ Windows 10 PC. Run it through NCE USB to Command Bus. Set up exactly the same as the ‘old’ computer. Same Router, cables etc. Now though Whilst I can access

But you can print a switch list?? A switch list is simply the manifest for a location. Can you try this, print out the switch list for every location the train visits.? Maybe one of the locations

Yes, I'm using the same format for manifest and switch lists. I can preview the manifest There are no error messages to the system console. JMRI thinks it's printed the manifest.? The error is