开云体育

Just downloaded and installed JMRI 4.17.7. Last night on 4.17.6 I found a problem with the Consist pane of TCS WOW steam decoder page. Today I tried it on 4.17.7 on both Steam and Diesel Consist

Andy, The NX flashing is not a function of the sensor state. That is done internally by the NX code. The web panel does not know about the alternating icon image. The other prerequisite for web NX

Dave You've hit the nail on the head there! I was using zoom 1.5. It seems that anything other than "No Zoom" exhibits the flashing problem. I'm guessing that this might be case on other operating

I've just tried java 1.8.0_232-ea and it exhibits the same problem, so by my reckoning that leaves Ubuntu 19.10. That still leaves open the question of which flavours or versions of linux might be

Andy, Make sure that your panel is at zoom level 1. This will affect the native panel flashing behavior. Dave Sand

Steve, Thanks for trying that on Windows On that basis as JMRI is the same version I assume: * web flashing is not programmed at all * native panel flashing it affected by either Ubuntu or the java

Test version 4.17.7 of JMRI/DecoderPro is available for download. This is the next in a series of test releases that will culminate in a production release, hopefully in early December 2019. We're

Is there a reason you need to use the two-bit-pulse form from JMRI? That makes your Arduino logic really complicated because it has to decode a lot of possible states. It would perhaps be simpler to

Hi Andy, have just tested your panel on an older laptop. In LE the NX Entry button seems fine to me with a regular flash, no difference when hovered over. The only way I found of getting irregular

Hi I'm using NX Routing in Layout Editor, both on native Panel and on the Web. I can get the routes to set correctly by using the entry and exits sensors. However, the entry sensor does not flash at

Thomas, I don't spend enough time on Macs. Back in the 80's I did. Didn't really get into PC/Windows until 90 or so. I had been doing Unix (or CPM) in the 80's for work. Also just about everything

How do I configure the section of track in the middle of the layout (the orange reverse block) as auto-reversing. ?I will be using the Digitrax BXPA1 to handle the self reversing, detection and

Thanks guys. Hopefully by sometime next week, I’ll be all back up and running. Thomas Cain Indianapolis, IN atsf93@... See my NEW website and layout at: www.atsf93.com Modeling the

Thomas, The standard JMRI install location on a Mac is /Applications/JMRI. The user data, such as panels, connection settings, profiles and roster are located at

Ken, My computer is a Mac. And I will be going a similar Mac. The train computer is 12 years old and the computer which will replace it is 6 years old. I have been using the time machine with both

Dave, Thanks for the information on the link to the Profile File Structure information. Somehow in my current computer, the settings in preferences on where files are located went out of whack.

Look in the Digitrax group in the file section and there are excel spread sheets that calculates the addresses. Missed a C siding on driver 8 which ends the count at 2752 in your example (not 2750).

Wayne, I'm not sure that's the best choice. You need to look at the tables from Digitrax (or do your own math) about what turnout and sensor numbers are defaulted based on the board id of that board.

DS64's? ? ? ? ? ? ? ? ?10X's? = Addresses 10-80 DBL-168? ? ? ? ? ? ? ?20x's? = Addresses 305-464 SE8C? ? ? ? ? ? ? ? ? ? 30x's? = Addresses 2113-2750 Document so its

Ken, This has nothing to do with JMRI and should be taken to the Digitrax forum. /g/Digitrax-Users -- Peter Ulvestad JMRI Users Group Moderator - http://www.jmri.org (