¿ªÔÆÌåÓý

  1. Jmriusers
  2. Messages
Expanded Topics Messages Polls
Date
Locked Re: SECTIONS TABLE NEW BUG

 

Mitch,

Your layout plan has two reverse loops and what is effectively a double crossover at 6/8. ?It appears that these characteristics are causing issues with block routing. ?The automatic signal mast logic uses block routing to identify the necessary blocks and turnouts between each pair of masts. ?In your case, the route from S01 to S08 is impacted, along with an invalid route from S01 to S04. ? The S04 problem is caused by a reverse loop and that destination needs to be deleted. ?The S01/S08 pair will have to be manually defined.

I tried a number of ideas and was able to get S01 to S08 to be automatic. ?I had to replace the 6/8 track work with left hand and right hand crossovers. ?After carefully assigning the blocks, SML discovery worked.

Sections

A change made at 4.17.2 is causing Java errors in the sensor section (for both direction and stopping sensors) when the sensor does NOT have a user name. ?I will be submitting a fix for that error which should be included in 4.17.5.

The screen shot appears to be a side effect of the Java error since I did not see it during my testing.

Dave Sand


On Sep 22, 2019, at 12:53 AM, Mitchell via Groups.Io <mitchell.scott93@...> wrote:

okay so..

When I do the delete paths routine, save, reload, and generate signal pairs.. the S01 to S08 path works, SML shows the blocks used etc.

I save the file, close JMRI, re-load and then check, and that is the ONLY SML that loses its blocks, and creates the null error as described before. Panel?S01 also shows red when should be green for S08, proving the point.
So delete paths works
Create new paths works when retarted because the SML works when first created..
and as soon as the XML is saved, it stops working after a restart.
--?
Thanks
Mitch
Locked Re: 2 problems: Layout editor misbehaving, and persistent profile

 

Hal,

The Layout Editor grid is drawn to be a bit larger than the furthest right and lowest objects on the panel. If you add another turnout to the right of the first one, the grid will adjust.

I recommend that you create separate profiles based on the required connections.

Dave Sand

On Sep 22, 2019, at 2:53 PM, haltz@... wrote:

I'm trying to build a new layout in LE, nd right off the bat run into this weird problem: in a new Layout, I add a turnout. Then I move it (left-click, drag) and the layout surface truncates to a width just a little to the right of the turnout. So the LE starts with a 13x7 (approx) grid (of the large squares, and suddenly it's only 3x6. Any ideas

Also,I am having problems with profiles. One of the demos called for setting Connections to Loconet, so I did that. Now I consistently have three Loconet windows appearing, and if I change the Connections to NCE, which I want, and save it, it does NOT ask me to restart Panelpro. It's as if it's not saving the config. When I quit and restart, it's again set to Loconet. Is there a file I can delete to start afresh?

Thanks.
Locked 2 problems: Layout editor misbehaving, and persistent profile

 

I'm trying to build a new layout in LE, nd right off the bat run into this weird problem: in a new Layout, I add a turnout. Then I move it (left-click, drag) and the layout surface truncates to a width just a little to the right of the turnout. So the LE starts with a 13x7 (approx) grid (of the large squares, and suddenly it's only 3x6. Any ideas

Also,I am having problems with profiles. One of the demos called for setting Connections to Loconet, so I did that. Now I consistently have three Loconet windows appearing, and if I change the Connections to NCE, which I want, and save it, it does NOT ask me to restart Panelpro. It's as if it's not saving the config. When I quit and restart, it's again set to Loconet. Is there a file I can delete to start afresh?

Thanks.
Locked Re: Operations - Question from a beginner #operationspro

 

Hi Paul,

Great news you got it working.? To your issue with Build Failures, remember you can always put virtual staging tracks at each end of your JMRI Ops railroad to give all the cars enough space to go.? I did this as part of the planning of my railroad, then once the actual staging yards were built the virtual tracks came out.

Cheers, Dennis Drury
Dayton, NV

The miracle is this: the more we share the more we have.
Leonard Nimoy



On Sun, Sep 22, 2019 at 11:32 AM <csxpaul@...> wrote:
Looks like I found the problem!?

In train build options, "allow cars to travel from origin to terminal" was checked. By unchecking that the switch list gave me orders to swap an empty for a loaded flatcar.

The only problem now is that the program must often find destinations for more cars than my woefully incomplete layout can accommodate so I'm getting a lot of "Build Failed" when I build trains.

I suspect the program will work better for me once I have a bigger yard and more spurs in place.

Thanks again for all the help. If anyone has any other info that might help...I'm here to learn!

Paul

Locked Re: Operations - Question from a beginner #operationspro

 

By the way, Breezly. That setting was shown in the build report so you were right, the problem was identified there.

Thanks, Everyone
Paul
Locked Re: Operations - Question from a beginner #operationspro

 

Looks like I found the problem!?

In train build options, "allow cars to travel from origin to terminal" was checked. By unchecking that the switch list gave me orders to swap an empty for a loaded flatcar.

The only problem now is that the program must often find destinations for more cars than my woefully incomplete layout can accommodate so I'm getting a lot of "Build Failed" when I build trains.

I suspect the program will work better for me once I have a bigger yard and more spurs in place.

Thanks again for all the help. If anyone has any other info that might help...I'm here to learn!

Paul
Locked Re: Control number of lines going to printer per page-OPERATIONS

 

Off the top of my head is font changeable on manifest as to size of type it may just be the matter of a couple of points causing the issue.


On Sun, Sep 22, 2019, 8:39 AM Frank in Houston <upitrr@...> wrote:

Hi. Yes the PDF printed fine so I guess it is a printer issue. I just wonder why the results would be different? Interesting. I cannot find any setting on the printer to ?do something that can correct it.?

THANK YOU Dan?
Locked Re: Control number of lines going to printer per page-OPERATIONS

Frank in Houston
 

Hello. I use an Epson Work force WF 3720 ink jet and the PDF prints just fine. But the manifest is one line to large and the bottom line is a one/half line as if the bottom half of that one line is out of range for the printer.?

What confuses me is I have been using this same printer for a couple years with no problem. This problem appeared when I downloaded the very latest JMRI release which was 4.17.4.?

I hate to have to PDF all manifests for my 16 trains and then go back and print all 16 trains. THANK YOU?
Locked Re: Operations - Question from a beginner #operationspro

 

Breezly,

I just built a train from a staging track which contained one loaded flatcar. There is an empty flatcar on the spur in question now.

I would expect the switch list would have me pick up the empty car and drop off the loaded one but it does not. It has me only pick up the empty but not drop off the loaded one.?

I viewed the build report for this train but didn't see anything that helped me find the problem. What did you mean by "do a car find"? Finding this car from the cars page only highlights it the car list. What should I be looking for in the report?

Thanks
Paul
Locked catalogTrees.xml pusrpose?

 

All,

? ? ?Was moving my updated JMRI layout file from my notebook over to my raspberry pi and noticed after bootup that the block values were missing.? So I assumed that there must be some other file holding them in my user directory.? Saw the blockvalues.xml and the dispatcheroptions.xml, but what is this catalogTress.xml for?

Roger
Locked Re: Decoder Pro Loco Sequence

 

Charley,

The top of each column can be clicked on to arrange that column in either ascending or descending order. Each click will reverse the order.

On Sun, Sep 22, 2019 at 10:01 AM Charley Goddard via Groups.Io <cgalfa=[email protected]> wrote:
My Roster has some locos out of numerical sequence.? Using? Win 10, Lenz LZV100, LH100, LI-USB.? How can I correct that?

Charley Goddard
Muncie, IN



--
John Griffin? ? ? ? ? ? ? ? ?
_______________________________
If today was your last day...
Locked Re: Operations - Question from a beginner #operationspro

 

Breezly seems to think the answer may be in the build report. I am not familiar with these as a beginner but I will look into it and see it there is something in it that helps me find out what's going on. If I get to the bottom of it I'll let you all know what it was.

Thanks
Paul
Locked Re: Operations - Question from a beginner #operationspro

 

Thanks, Dennis. I have already checked that, in fact I added length to the spur to be safe :-)

It did not help.

Thanks
Paul
Locked Re: Operations - Question from a beginner #operationspro

 

Thanks for the reply, Bob. While I do appreciate the help you are the third person to tell me to set the move count to 4.
If you read my second post you will see that no scenario calls for more than 2 moves.?

Just to make sure there isn't a arithmetic mistake in the program I did change the move count to 4 but it did not help. Therefore this is happening for some other reason.

Thanks
Paul?
Locked Decoder Pro Loco Sequence

Charley Goddard
 

My Roster has some locos out of numerical sequence.? Using? Win 10, Lenz LZV100, LH100, LI-USB.? How can I correct that?

Charley Goddard
Muncie, IN
Locked Re: Control number of lines going to printer per page-OPERATIONS

[email protected]
 

What brand and model of printer do you use? Laser, ink jet or antique dot matrix?

On Sunday, September 22, 2019, 10:42:00 AM GMT-4, Mike Saunders <msaundersvt@...> wrote:


As a work around print the P D F and see if it prints on printer ok.


On Sun, Sep 22, 2019, 8:39 AM Frank in Houston <upitrr@...> wrote:

Hi. Yes the PDF printed fine so I guess it is a printer issue. I just wonder why the results would be different? Interesting. I cannot find any setting on the printer to ?do something that can correct it.?

THANK YOU Dan?
Locked Re: Control number of lines going to printer per page-OPERATIONS

 

As a work around print the P D F and see if it prints on printer ok.


On Sun, Sep 22, 2019, 8:39 AM Frank in Houston <upitrr@...> wrote:

Hi. Yes the PDF printed fine so I guess it is a printer issue. I just wonder why the results would be different? Interesting. I cannot find any setting on the printer to ?do something that can correct it.?

THANK YOU Dan?
Locked Re: Operations - Question from a beginner #operationspro

 

Hello Paul,

JMRI Operations adds 4 feet to the length of each car to account for the couplers.? Make sure the spur length is long enough to hold both cars.? Hope this helps.

Cheers, Dennis Drury
Dayton, NV
Locked Re: Operations - Question from a beginner #operationspro

 

What you want to do requires the location/spur to allow 4 moves.
The act of dropping a car is a move the act of picking up a car is one move so it takes 2 moves to drop and pick up a car
2 cars = 4 moves
Locked Re: Control number of lines going to printer per page-OPERATIONS

 

Frank

I use three printers during a session. All my paperwork is Excel generated so I use the "fast draft" setting as to print quality. However, if I forget and do not change that to normal when printing out my car locations after a session, the printed area will exceed the width of the paper.

Just a thought

Dave
Trempealeau WI
76741 - 76760 of 240402