开云体育

On a RPI 3B+ all you need is a 8 gb SC card and you will use about half of its space. If you want a bit more room in case you add some other stuff, then go up to 16gb. I use 8 GB and jmri sails

I'm confused. I thought Buster was only for the Pi 4, but now find online that maybe it can be used on my 3B+ if I put a big enough memory chip on it. What models of RPI, with what memory chips would

Klaus, SUCCESS!!!? ?A working ZIMO NW2 engine.? Flawless notches at 12,24,36,48,60,72 & 80.? Great start and shutdown sounds.? My thanks to Oliver Zoffi for the very nice sounds.? Definitely

Conrad, That sounds good. Good luck with the transition sounds! Klaus Am 07.09.2019 um 18:14 schrieb conrad:

i have currently 9 Digitrax DS64 per there recemidations I created ID# 101 - 109. I also named each switch address 1 thru 36. In Panel Pro where does it see the address for the DS64? It’s seeing the

Klaus, I'm back at it and making progress.? Tried system console and got a large error list.?Took a fresh approach.? My mistake was that I had too many NW2 config files and? was apparently

Thanks, G There's a new version here: https://mvmills-my.sharepoint.com/:u:/p/stevet/EXUw5otCTKtKvecqH8JCh7sBMwjmaNzwPoH7jT2DSE8JLw?e=2sdOBP It includes the latest Buster updates and JMRI

mcdougle1979, A long shot: Take a look at the Advanced pane (Read Full Sheet first) and make sure "Automatic Speed Step Detection" is enabled. I don't think it will help greatly but worth a

mcdougle1979 (Name please – we are ‘friends’ and generally converse on a first-name basis ?) The Sprog FAQ has a link to “The unit doesn’t allow me to operate the throttle above level

mcdougle1979 We are talking about the SPROG Console menu item and the SPROG throttle Speed Step Mode setting there. You need to check that and make sure it isn't at 14. That governs both Engine

mcdougle1979, Good way to mess up your decoders... But a decoder reset should fix that. Looks like you're doing something wrong (unrelated to ESU). Dave in Australia

I'm using JMRI with Sprog. Same effect if using Engine Driver or just on-screen throttle. I've not changed the speed steps, but I had this once before and had to program the decoder to 14 (as it was

Bought from Legomanbiffo. Installed all 3 in locos, programmed just the address and they worked OK. Swapped the speaker over and now not working. I was using latest Production version. I've just

mcdougle1979, Have you possibly set your DCC system to send 14 2peed-step commands to this locomotive address? What DCC system (and what throttle) are you using? Ross Sent: Saturday, September 7,

mcdougle1979, Who loaded the Sound File into the decoders? 1) Did you do it yourself using LokProgrammer. 2) Did you buy it from a vendor who had preprogrammed it? 3) ESU does not load sound Files

Installed and tested v5 decoders. Seemed to be working ok. Changed the speakers over, now the deciders are misbehaving. They only respond in6 14 speed steps - anything above step 14 brings the loco to

If it is old enough, it may not support anything but the standard NMRA registers. Try reading register 1 in register mode. I have a couple of old decoders I have to do this with. Paul

Roger, friends, This topic is GREAT. I have one small suggestion. I "occasionally" help others build and modify panels . One major problem is that when custom icons are used, and an xml file is sent

Thanks so much Dave for spending time on this. I will try it out over the weekend! Dave B

All, Thank you for the replies. I have successfully update my UR-92 using the Digitrax S/W and Locobuffer. I believe the correct baud rate is 57600 (the only option some of the Digitrax programs