Locked
Re: DecoderPro &ESU LokSound Factory reset
Frank,On 3 Aug 2019, at 12:30 AM, Frank in Houston <upitrr@...> wrote:
OK DAVE, I will do it. ?THANK YOU AGAIN....I switched from Paged Mode to Direct mode. ?(Yes, much, much faster). ?Next, I placed the Atlas locomotive on the program track. ?I then used "Read Type from Decoder" and DecoderPro identified the manufacturer as ESU...however DecoderPro then highlighted about 80 % of the listed Decoder types. ?So I chose "LokSound Select OEM" and then used READ Full Sheets on the CV pane and all seemed to work just fine except the horn. ???It does not work when I push the Botton. On all previous attempts I used "LokSound Select"....and the horn worked.
This concerns me greatly. The latest JMRI version should uniquely identify every LokSound V4/Select/Essential Sound Unit/5 decoder manufactured ?by ESU and supported by ESU's LokProgrammer V5.0.7.Please perform the following test for me:1) Place your loco on the the Program Track.2) Using "Direct Mode", do a New Loco->Read Type From Decoder.3) Don't create a new loco, simply close the Window (tell us how many it picked).4) Go to the Help->System Console window and you should see a line like this: "IdentifyDecoder INFO ?- Decoder returns?mfgID:151;modelID:255;productID:33554511" 5) Please Select, Copy and Paste that line into a message for me.
I need to see the three values it is returning for?mfgID, modelID and productID.
Dave in Australia
|
The help file is part of the JMRI download. There isn't a separate one to download.
Why don't you tell us what you think is missing.
--
Peter Ulvestad
JMRI Users Group Moderator - ( )
Tam Valley Group Moderator - ( )
Sprog-DCC Group Moderator - ( )
Edmonton Model Railroad Association -
|
Locked
Re: Pausing in a section JMRI ver 4.15.9
Hi Roger
The Pause action has more than a few issues that have been around for ever. It tends to only work on entry no delay, and uses a different stopping method than anywhere else.
Using a multi block end section for back and forth has issues as well.
Steve G.
toggle quoted message
Show quoted text
On August 2, 2019 6:05:37 PM EDT, Roger Merritt <merritt_roger@...> wrote:
Steve,
??
? ? ?I've tried running a 80 foot train through that section which has a 100 foot first block.? On either Block entry or section entry is goes to the very last block and stops.? I made a test transit with that area I wanted the train to stop at and it does in fact stop in that block I wanted.
? ? However, these section I am dealing with is a passenger yard,? Wanting to use the other track also as an alternate track.? Since I first made this passenger yard tracks, I'm using two blocks.? One for the passenger cars to sit in and one for the loco to sit in.? I'll have to combine these two tracks since I know longer need the loco block.
? ?The gist of this is that I can not use Alternate sections if the sections have two blocks and expect it to stop where I want it to.? ?Just pointing out a problem with the "Pause" action.
Roger
--
Sent from my Android device with K-9 Mail. Please excuse my brevity.
|
i noticed that my DP help is missing info on many topics in the left pane. Do I need to D/L a new help file?
|
Locked
Re: Versions 4.16 & 4.17
Marc, On 3 Aug 2019, at 8:11 AM, forfoum@... wrote:
Much of what is written is done by dev people who have systems with more content than any DEFAULT JMRI Install shows. One example is DROPBOX
The screen captures are of a DEV machine with absolutely no indication of My_JMRI_Railroad. Any newb looking at this will need to be up to speed.
Anyone who has fandangled there JMRI install will have little problem grasping it. Newbs, not so sure.
Those of us creating profiles and setting up JMRi to our liking probably do not need DROPBOX instructions. The Dropbox instructions are created for the benefit of many users who set up shared User Files, Rosters, Profiles etc. Many of these will have got rid of their My_JMRI_Railroad default profile by now. (The illustrations are not from my computer. I wrote the text, Bob Jacobsen did the screenshots. Dave in Australia
|
Locked
Re: Versions 4.16 & 4.17
I see what you mean, but it's pretty easy (at least for me) to assume that 'Roster Location' and 'Roster Folder' are the same place.
I was educated in an era when syntax, punctuation and capitalisation were treated as very important. I now 'work' as a JMRI developer, with Java code, Mac/UNIX case-sensitive file and command structures, etc. where correct? syntax, punctuation and capitalisation are even more important
'Roster Folder' (a term you have coined) is not the same as 'the "roster" folder' (the term we use).
Hence?'Roster Location' and 'the "roster" folder'?are not the same place. And it does say that the media files can be in the Roster Location, which is apparently incorrect. If the roster.xml and the loco.xml/ media files are supposed to be in two separate locations then maybe add a statement to the effect. Just a suggestion.
I'm fixing that. I would also suggest adding a link to the ProfileFileStructure page to the Technical Section of the main JMRI Help page unless it's there already and I just can't see it.. I can never find it when I need it.
Links were supposed to be added, but seem to have been overlooked/removed.
Dave in Australia
|
Locked
Re: Pausing in a section JMRI ver 4.15.9
Steve,
??
? ? ?I've tried running a 80 foot train through that section which has a 100 foot first block.? On either Block entry or section entry is goes to the very last block and stops.? I made a test transit with that area I wanted the train to stop at and it does in fact stop in that block I wanted.
? ? However, these section I am dealing with is a passenger yard,? Wanting to use the other track also as an alternate track.? Since I first made this passenger yard tracks, I'm using two blocks.? One for the passenger cars to sit in and one for the loco to sit in.? I'll have to combine these two tracks since I know longer need the loco block.
? ?The gist of this is that I can not use Alternate sections if the sections have two blocks and expect it to stop where I want it to.? ?Just pointing out a problem with the "Pause" action.
Roger
|
Locked
Re: Help getting JMRI working on a new WIN10 computer
OK - right. It was only as the logs were never mentioned that I chimed in on the off-chance. All bases covered, then, apparently. Wouter
On Fri, Aug 2, 2019 at 03:27 PM, whmvd wrote:
Here's another one (my special subject is the blindingly obvious): I've skimmed through the entire thread once again, and I never once see that either the log-files were checked or someone suggesting checking them. I mean... you never know!
Wouter,
The System Console log file, when a Locobuffer (or any Loconet based device)? is involved, does not provide much. This is not like NCE and all the details that are thrown back and forth. All we see in the log is the connection type that was opened and all the other JMRi housekeeping. Even with the error condition replicated, there is nothing in the log that reports or shows it occuring.? This is pure USB.?
NCE is USB and RS-232 so there is much checking if USB is ok, then RS-232 baud and jumpers. None of this in the Loconet interface world
I've encountered defective Locobuffer-USB before and the console log was of no help.
Ross has been at this for a long time and I have read him for years (never met) on different forums, so I know he has dotted all the "I"s.
- - - - -
Here is a log with the system working fine
2019-08-02 16:11:50,044 util.Log4JUtil??????????????????????? INFO? - * JMRI log ** [main]
2019-08-02 16:11:50,106 util.Log4JUtil??????????????????????? INFO? - This log is appended to file: C:\Users\Marc\JMRI\log\messages.log [main]
2019-08-02 16:11:50,106 util.Log4JUtil??????????????????????? INFO? - This log is stored in file: C:\Users\Marc\JMRI\log\session.log [main]
2019-08-02 16:11:50,122 apps.AppsBase???????????????????????? INFO? - DecoderPro version 4.15.9+Re0a9348 starts under Java 1.8.0_221 on Windows 7 x86 v6.1 at Fri Aug 02 16:11:50 EDT 2019 [main]
2019-08-02 16:11:50,621 gui3.Apps3??????????????????????????? INFO? - Starting with profile My_JMRI_Railroad.3f1fffbb [main]
2019-08-02 16:11:50,933 node.NodeIdentity???????????????????? INFO? - Using 0498c833-19ae-450b-a194-45038afda399 as the JMRI storage identity for profile id 3f1fffbb [AWT-EventQueue-0]
2019-08-02 16:11:51,182 xml.AbstractSerialConnectionConfigXml INFO? - Starting to connect for "LocoNet" [main]
2019-08-02 16:11:51,822 pr3.PR3Adapter??????????????????????? INFO? - PR3 adapter set hardware flow control, mode=2 RTSCTS_OUT=2 RTSCTS_IN=1 [main]
2019-08-02 16:11:51,838 locobuffer.LocoBufferAdapter????????? INFO? - COM2 port opened at 57600 baud with DTR: true RTS: true DSR: true CTS: true? CD: false [main]
2019-08-02 16:11:51,931 loconet.LnPacketizer????????????????? INFO? - lnPacketizer Started [main]
2019-08-02 16:11:52,571 util.FileUtilSupport????????????????? INFO? - File path program: is C:\Program Files\JMRI\ [main]
2019-08-02 16:11:52,586 util.FileUtilSupport????????????????? INFO? - File path preference: is C:\Users\Marc\JMRI\My_JMRI_Railroad.jmri\ [main]
2019-08-02 16:11:52,586 util.FileUtilSupport????????????????? INFO? - File path profile: is C:\Users\Marc\JMRI\My_JMRI_Railroad.jmri\ [main]
2019-08-02 16:11:52,586 util.FileUtilSupport????????????????? INFO? - File path settings: is C:\Users\Marc\JMRI\ [main]
2019-08-02 16:11:52,586 util.FileUtilSupport????????????????? INFO? - File path home: is C:\Users\Marc\ [main]
2019-08-02 16:11:52,586 util.FileUtilSupport????????????????? INFO? - File path scripts: is C:\Program Files\JMRI\jython\ [main]
- - - -
Here is a log with the Loconet cable remove and the 8 blank boxes showing, no control on layout
2019-08-02 16:15:00,926 util.Log4JUtil??????????????????????? INFO? - * JMRI log ** [main]
2019-08-02 16:15:00,957 util.Log4JUtil??????????????????????? INFO? - This log is appended to file: C:\Users\Marc\JMRI\log\messages.log [main]
2019-08-02 16:15:00,957 util.Log4JUtil??????????????????????? INFO? - This log is stored in file: C:\Users\Marc\JMRI\log\session.log [main]
2019-08-02 16:15:00,972 apps.AppsBase???????????????????????? INFO? - DecoderPro version 4.15.9+Re0a9348 starts under Java 1.8.0_221 on Windows 7 x86 v6.1 at Fri Aug 02 16:15:00 EDT 2019 [main]
2019-08-02 16:15:01,456 gui3.Apps3??????????????????????????? INFO? - Starting with profile My_JMRI_Railroad.3f1fffbb [main]
2019-08-02 16:15:01,768 node.NodeIdentity???????????????????? INFO? - Using 0498c833-19ae-450b-a194-45038afda399 as the JMRI storage identity for profile id 3f1fffbb [AWT-EventQueue-0]
2019-08-02 16:15:02,018 xml.AbstractSerialConnectionConfigXml INFO? - Starting to connect for "LocoNet" [main]
2019-08-02 16:15:02,642 pr3.PR3Adapter??????????????????????? INFO? - PR3 adapter set hardware flow control, mode=2 RTSCTS_OUT=2 RTSCTS_IN=1 [main]
2019-08-02 16:15:02,657 locobuffer.LocoBufferAdapter????????? INFO? - COM2 port opened at 57600 baud with DTR: true RTS: true DSR: true CTS: true? CD: false [main]
2019-08-02 16:15:02,751 loconet.LnPacketizer????????????????? INFO? - lnPacketizer Started [main]
2019-08-02 16:15:03,375 util.FileUtilSupport????????????????? INFO? - File path program: is C:\Program Files\JMRI\ [main]
2019-08-02 16:15:03,390 util.FileUtilSupport????????????????? INFO? - File path preference: is C:\Users\Marc\JMRI\My_JMRI_Railroad.jmri\ [main]
2019-08-02 16:15:03,390 util.FileUtilSupport????????????????? INFO? - File path profile: is C:\Users\Marc\JMRI\My_JMRI_Railroad.jmri\ [main]
2019-08-02 16:15:03,390 util.FileUtilSupport????????????????? INFO? - File path settings: is C:\Users\Marc\JMRI\ [main]
2019-08-02 16:15:03,390 util.FileUtilSupport????????????????? INFO? - File path home: is C:\Users\Marc\ [main]
2019-08-02 16:15:03,390 util.FileUtilSupport????????????????? INFO? - File path scripts: is C:\Program Files\JMRI\jython\ [main]
Marc
|
Locked
Re: Versions 4.16 & 4.17
One thing to add. If the roster.xml file and the locoxxx.xml and images are supposed to be in two separate locations, then the <>???is incorrect. According to it, they should be in the same directory.
Thanks for catching that error in the documentation. I will fix that this morning.
It should read:
"Roster Location (portable name = "roster:")This location contains:- Your "roster" folder. This contains:
- An XML file for each loco entry in your roster, with stored CV values, etc.
- Copies of media files you have added to roster entries, throttles etc.?
(Older JMRI versions stored roster images in a "resources" folder in the User Files Location. If you have been using JMRI for a long time, you may have roster images in both locations.) - ".bak" files, which are backup versions of entries in your roster.
- A "consist" folder, which stores information on consists you have created using the Consist tools in JMRI.
- A "roster.xml" file, which is a (recreatable) index of the XML files in the "roster" folder. You should create/recreate "roster.xml" (Actions->Recreate Roster Index) if it is missing or you are experiencing roster problems.
By default the Roster Location is the same as (and follows) the User Files location unless you explicitly set a different location. You are free to change the Roster Location as you like (Preferences->Roster->Roster->Location Set/Reset). The Reset button causes the Roster Location to again follow the User Files location." I will fix that this morning.
Dave in Australia
|
Locked
Re: Pausing in a section JMRI ver 4.15.9
Steve,
? ? Maybe it has to do with train length.? I'll check that out next. But strange thing is I did a test with the single block section behind it and the train did slow down when it entered the block and stopped after the last block was cleared, but it had also entered the block ahead.? Not so with the two block section.
Roger
|
Locked
Re: Help getting JMRI working on a new WIN10 computer
Here's another one (my special subject is the blindingly obvious): I've skimmed through the entire thread once again, and I never once see that either the log-files were checked or someone suggesting checking them. I mean... you never know!
Wouter
Marc,
?
Thank you for the info.? I¡¯ll be checking carefully next time I¡¯m at the club.
?
Ross
?
From: [email protected] <[email protected]> On Behalf Of
forfoum@...
Sent: Friday, August 2, 2019 1:24 PM
To: [email protected]
Subject: Re: [jmriusers] Help getting JMRI working on a new WIN10 computer
?
I had suggested BIOS in post? #162322,
In HP computers, USB are either on or off via Port Options. If this option is OFF, no USB port comes active but they do put out 5 volts to charge USB devices.? The other option is Legacy USB mode On/Off.? To use older USB1 USB2 devices. This usually relates
to keyboards and mice.
USB is 4 wires, Data +. DATA -, 5 V and a Ground.? Sort of limits what could be wrong USB mechanics wise.
Gents, It is not a driver issue. 8 boxes showing up for Monitor Loconet Stats (MLS) means the driver is OK,? the device has a valid com port assigned and JMRI can see it and " use it " .? The same device attached to a different computer WORKS? (as per My friend
Ross)
A working setup of LB-USB should display the blank 8 boxes for a second +/- and switch to three boxes displaying FW Ver, Breaks and Errors.
Testing I have done were the Monitor Loconet Stats shows 8 blank boxes is when the LOCONET cable is not present. The LB-USB gets power from the RailSync of Loconet. Without this, half the LB-USB is inoperative.? You see this by the indicators of the LB-USB.
I have several Loconet cables I intentionally modified for testing purposes. One has missing RailSync, other missing Grounds, third is missing Loconet
If RailSync is missing the RailSync led on LB-USB will not come active.
If Loconet wires are missing, the LB-USB will indicate good RailSync power but MLS will display 8 blank boxes. No control on layout.
I would tend towards a Loconet cable issue, a faulted upstream or downstream device on Loconet.
Marc
|
Locked
Re: DecoderPro &ESU LokSound Factory reset
Hooray....It is working. I can once again blow the horn. ?I finally got the right LokSound version by calling Atlas and they told me to use LokSound select. ? So now all is working. ?I want to thank ALL who provided information and help in solving this problem for me. ?It seems that these engines were new in the box but a little older than I thought. ?However all is running just fine and many thanks?
Frank
|
Locked
Re: Help getting JMRI working on a new WIN10 computer
Have you checked that +/- 5 v is really there? or is it just close? I use powered hubs that ensures that my voltage is true and also allows me additional devices such as a 2tb HDD for my Raspbery Pi.
On Friday, August 2, 2019, 02:56:49 PM GMT-4, Ross Kudlick <Ross_Kudlick@...> wrote:
Marc,
?
Thank you for the info.? I¡¯ll be checking carefully next time I¡¯m at the club.
?
Ross
?
From: [email protected] < [email protected]> On Behalf Of
forfoum@...
Sent: Friday, August 2, 2019 1:24 PM
To: [email protected]
Subject: Re: [jmriusers] Help getting JMRI working on a new WIN10 computer
?
I had suggested BIOS in post? #162322,
In HP computers, USB are either on or off via Port Options. If this option is OFF, no USB port comes active but they do put out 5 volts to charge USB devices.? The other option is Legacy USB mode On/Off.? To use older USB1 USB2 devices. This usually relates
to keyboards and mice.
USB is 4 wires, Data +. DATA -, 5 V and a Ground.? Sort of limits what could be wrong USB mechanics wise.
Gents, It is not a driver issue. 8 boxes showing up for Monitor Loconet Stats (MLS) means the driver is OK,? the device has a valid com port assigned and JMRI can see it and " use it " .? The same device attached to a different computer WORKS? (as per My friend
Ross)
A working setup of LB-USB should display the blank 8 boxes for a second +/- and switch to three boxes displaying FW Ver, Breaks and Errors.
Testing I have done were the Monitor Loconet Stats shows 8 blank boxes is when the LOCONET cable is not present. The LB-USB gets power from the RailSync of Loconet. Without this, half the LB-USB is inoperative.? You see this by the indicators of the LB-USB.
I have several Loconet cables I intentionally modified for testing purposes. One has missing RailSync, other missing Grounds, third is missing Loconet
If RailSync is missing the RailSync led on LB-USB will not come active.
If Loconet wires are missing, the LB-USB will indicate good RailSync power but MLS will display 8 blank boxes. No control on layout.
I would tend towards a Loconet cable issue, a faulted upstream or downstream device on Loconet.
Marc
|
Locked
Re: Versions 4.16 & 4.17
I see what you mean, but it's pretty easy (at least for me) to assume that 'Roster Location' and 'Roster Folder' are the same place. And it does say that the media files can be in the Roster Location, which is apparently incorrect. If the roster.xml and the loco.xml/ media files are supposed to be in two separate locations then maybe add a statement to the effect. Just a suggestion.
I would also suggest adding a link to the ProfileFileStructure page to the Technical Section of the main JMRI Help page unless it's there already and I just can't see it.. I can never find it when I need it.
In any event, I moved the roster.xml to the User Files location (the folder that contains the Roster folder along with the profile folders, systemfile, etc.) , renamed the roster.xml and .bak to 'Oldroster', reinstalled 4.17.2, and restarted DP with all of the media files showing on the roster.
Again, thank you everyone for helping me work through this.
--
Mike Heintzman
¡°Nae problemo!¡± was the last thing he said.
|
Locked
Re: Help getting JMRI working on a new WIN10 computer
Marc,
?
Thank you for the info.? I¡¯ll be checking carefully next time I¡¯m at the club.
?
Ross
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of
forfoum@...
Sent: Friday, August 2, 2019 1:24 PM
To: [email protected]
Subject: Re: [jmriusers] Help getting JMRI working on a new WIN10 computer
?
I had suggested BIOS in post? #162322,
In HP computers, USB are either on or off via Port Options. If this option is OFF, no USB port comes active but they do put out 5 volts to charge USB devices.? The other option is Legacy USB mode On/Off.? To use older USB1 USB2 devices. This usually relates
to keyboards and mice.
USB is 4 wires, Data +. DATA -, 5 V and a Ground.? Sort of limits what could be wrong USB mechanics wise.
Gents, It is not a driver issue. 8 boxes showing up for Monitor Loconet Stats (MLS) means the driver is OK,? the device has a valid com port assigned and JMRI can see it and " use it " .? The same device attached to a different computer WORKS? (as per My friend
Ross)
A working setup of LB-USB should display the blank 8 boxes for a second +/- and switch to three boxes displaying FW Ver, Breaks and Errors.
Testing I have done were the Monitor Loconet Stats shows 8 blank boxes is when the LOCONET cable is not present. The LB-USB gets power from the RailSync of Loconet. Without this, half the LB-USB is inoperative.? You see this by the indicators of the LB-USB.
I have several Loconet cables I intentionally modified for testing purposes. One has missing RailSync, other missing Grounds, third is missing Loconet
If RailSync is missing the RailSync led on LB-USB will not come active.
If Loconet wires are missing, the LB-USB will indicate good RailSync power but MLS will display 8 blank boxes. No control on layout.
I would tend towards a Loconet cable issue, a faulted upstream or downstream device on Loconet.
Marc
|
Locked
Re: Versions 4.16 & 4.17
On Fri, Aug 2, 2019 at 12:25 PM, Mike Heintzman wrote:
One thing to add. If the roster.xml file and the locoxxx.xml and images are
supposed to be in two separate locations, then the <
???is incorrect. According to it, they should be in the same directory.
Mike, Please reread that section and you will see you are incorrect. -- Peter Ulvestad JMRI Users Group Moderator - ( ) Tam Valley Group Moderator - ( ) Sprog-DCC Group Moderator - ( ) Edmonton Model Railroad Association -
|
Locked
Re: Versions 4.16 & 4.17
One thing to add. If the roster.xml file and the locoxxx.xml and images are supposed to be in two separate locations, then the <>???is incorrect. According to it, they should be in the same directory. "Roster Location (portable name = "roster:")This location contains:
- Your "roster" folder. This contains:
- An XML file for each loco entry in your roster, with stored CV values, etc.
- ".bak" files, which are backup versions of entries in your roster.
- A "consist" folder, which stores information on consists you have created using the Consist tools in JMRI.
- A "roster.xml" file, which is a (recreatable) index of the XML files in the "roster" folder. You should create/recreate "roster.xml" (Actions->Recreate Roster Index) if it is missing or you are experiencing roster problems.
- Copies of media files you have added to roster entries, throttles etc.?
(Older JMRI versions stored roster images in a "resources" folder in the User Files Location. If you have been using JMRI for a long time, you may have roster images in both locations.)
By default the Roster Location is the same as (and follows) the User Files location unless you explicitly set a different location.
You are free to change the Roster Location as you like (Preferences->Roster->Roster->Location Set/Reset). The Reset button causes the Roster Location to again follow the User Files location."
-- Mike Heintzman
|
Locked
Re: Pausing in a section JMRI ver 4.15.9
Roger,
Stopping is based on block length vs. train length, and whether or not you have resistor wheel sets checked. Or there's different logic if you have a speed profile for that loco.
What are those values in your situation? Are they accurate?
|
Locked
Re: Versions 4.16 & 4.17
Dave and all, The Roster directory, which is where Roster Location currently points to,? indeed contains the roster.xml file, the Locoxxx.xml files, and the image files. Dave, it also has a nested Roster directory in it which also contains all of the Locoxxx.xml files and image files. Curiously, it also contains a Consist directory which contains a Consist.xml file. I was fiddling with the Consist Tool on July 25 and that's the date on both the directory and Consis.xml file. I didn't create them so it must have been done by the software and put here for some reason. I didn't create either of the nested Roster or Consist directory, at least on purpose. What I propose to do is move the roster.xml file out of the Roster directory and into the User Files area and repoint the Roster Location Setting to this new location.? Below is the file structure requested. Thanks for the help and I'll let you know.
User Files Location: C:\Users\Mary\OneDrive\P&PU\JMRI\JMRI\
Roster Location: C:\Users\Mary\OneDrive\P&PU\JMRI\JMRI\Roster\
Profile Location: C:\Users\Mary\OneDrive\P&PU\JMRI\JMRI\No_decoder\
Settings Location: C:\Users\Mary\JMRI\
Current Config file:C:\Users\Mary\OneDrive\P&PU\JMRI\JMRI\No_decoder\ProfileConfig.xml
Scripts Location: C:\Program Files (x86)\JMRI\jython\
Program Location: C:\Program Files (x86)\JMRI
Temp Files Location:C:\Users\Mary\AppData\Local\Temp\
Log Files Location: C:\Users\Mary\JMRI\log\
? C:\Users\Mary\JMRI\log\messages.log
? C:\Users\Mary\JMRI\log\messages.log.1
? C:\Users\Mary\JMRI\log\messages.log.2
? C:\Users\Mary\JMRI\log\session.log
?
-- Mike Heintzman ¡°Nae problemo!¡± was the last thing he said.
|
Locked
Pausing in a section JMRI ver 4.15.9
All,
JMRI ver 4.15.9
Windows 10
Dispatcher using Auto run
? ? Having a problem getting a train to stop in a section that has two blocks.? I want it to stop in first block, but the different settings has it stopping in second block or past the section.? Crazy.
? ? Is this an old problem that has not been resolved.? Or this a situation where the pause action only works with single block sections?
Roger
|
Peter Ulvestad
Jim Kirwan
Roger Merritt
Mike Heintzman