Re: After Windows 11 upgrade I can no longer communicate via NCE USB module
#nce
#windows
Bill, ? You should be seeing the id 7.3.7 in the logs. That says ‘all systems’ so JMRI lets that match any of the command stations. ? -Ken Cameron, Member JMRI Dev Team
? ?
|
Re: After Windows 11 upgrade I can no longer communicate via NCE USB module
#nce
#windows
Yes, first and third were PowerCab and middle was SB5. All same profile, just changed the preferences. ? I put the jumpers back on the board, set it to 19,200 and it appears to be happier now. ?
toggle quoted message
Show quoted text
From: [email protected] <[email protected]> On Behalf Of Ken Cameron via groups.io
Sent: Sunday, March 09, 2025 11:47 AM
To: [email protected]
Subject: Re: [jmriusers] After Windows 11 upgrade I can no longer communicate via NCE USB module? Bill, ? I see three startups in the file. The first and third seem to be fine, but the second one has the problem. What was the settings in the connection for each of the three? To me, it looks like the 1st and 3rd was using a profile set for the PowerCab but the 2nd was set for using the SB5. But the log says these were all the same profile. That’s why I was asking about the connection settings for each startup of JMRI to match what was different. ? -Ken Cameron, Member JMRI Dev Team
? ?
|
Re: After Windows 11 upgrade I can no longer communicate via NCE USB module
#nce
#windows
Bill, ? I see three startups in the file. The first and third seem to be fine, but the second one has the problem. What was the settings in the connection for each of the three? To me, it looks like the 1st and 3rd was using a profile set for the PowerCab but the 2nd was set for using the SB5. But the log says these were all the same profile. That’s why I was asking about the connection settings for each startup of JMRI to match what was different. ? -Ken Cameron, Member JMRI Dev Team
? ?
|
Re: Frequently Asked Questions/Topics/Official Announcements?
On Sun, Mar 9, 2025 at 04:41 AM, whmvd wrote:
Sticky is all very well for people using the group's web interface. I don't, and I'm sure there are many like me who just let the messages arrive in email form, either individually or as digests.
?
Might be worth a poll.
?
Personally, I think a faq on the jmri site is a lot more useful, and the standard questions could than be handled with a reply in the form of a single link.
?
No, sticky isn't "all very well for people using the group's web interface." That's exactly the problem - When you use the Web interface, the first page is stickies you have to scroll through to get to any actual message threads.
?
And I follow far too many fora for my various hobbies to even consider email delivery. Been there, done that, with the filters and folders and filing - What a mess! Maybe that worked back in the dial-up days if you followed a small number of fora, but for me at least it's not a viable solution.
?
However, I do agree with your FAQ suggestion. I suggested putting them in the forum's Wiki, bit the JMRI Web site might also work (Although, apparently, not many folks bother to read the release notes there. I'm not sure the FAQ's would do any better.)
?
Steve
"Breezlys"
|
Re: After Windows 11 upgrade I can no longer communicate via NCE USB module
#nce
#windows
Here you go Ken, everything from today.
?
I will re-install the jumpers and tweak the Advanced settings to 19,200 vs 9,600 baud.
?
Bill
?
toggle quoted message
Show quoted text
From: [email protected] <[email protected]>
On Behalf Of Ken Cameron via groups.io
Sent: Sunday, March 09, 2025 10:30 AM
To: [email protected]
Subject: Re: [jmriusers] After Windows 11 upgrade I can no longer communicate via NCE USB module
?
Bill,
?
That log didn’t have the other run. The session.log gets reset every time you open JMRI. The messages.log is the last ### runs up a meg of file space.
?
I think what would be best is a post of the messages.log so I see the history and a snap of the connection profile showing all the settings.
?
-Ken Cameron, Member JMRI Dev Team
?
?
|
Re: After Windows 11 upgrade I can no longer communicate via NCE USB module
#nce
#windows
Bill, ? That log didn’t have the other run. The session.log gets reset every time you open JMRI. The messages.log is the last ### runs up a meg of file space. ? I think what would be best is a post of the messages.log so I see the history and a snap of the connection profile showing all the settings. ? -Ken Cameron, Member JMRI Dev Team
? ?
|
Re: After Windows 11 upgrade I can no longer communicate via NCE USB module
#nce
#windows
Ken,
There should be two sequences in there with the latter having it set for SB5 and resulting in the error.
I have three throttles on the bus, my original power cab (with procan cable), a second pro cab and a cab06 as well.
When I set to Pro Cab the system gives me the two green indicators on. Ottom.left and it does seem to read from a loco on the track.
_____________________________________________ Bill Suarez - +1 508-735-7877 - wsuarez@...
Bill, ? This log looks normal. I don’t see it showing any issue with opening the port, getting the id from the NCE USB. But what did you have set in the connection window at this time? ? I’m presuming you have both a PowerCab and a SB5 from what you said. The recommended setup for that combination would be using two profiles. One for the PowerCab as the command station so you have a programming track. The second is with
the SB5 as the command station so you can move around with the PowerCab as a normal throttle. ? But to do that, I suggest you make a change to the NCE USB. I would use it with all jumpers in place. This is the ‘all systems’ setting. That in turn would mean both profiles are set for 19,200 baud. This way you don’t have to change the
jumpers between the two systems. ? But there is a table of the id’s used by the NCE USB and the code cross checks that value with the command station selection. The message you posted would say the selection you had in the connection settings didn’t match the id value returned
by the NCE USB. ? I take it that this last run didn’t give you any popup? ? -Ken Cameron, Member JMRI Dev Team
? ?
|
Brett,
?
On Panel Editor it is straight forward. I used the SIM profile because I'm too lazy to pull my Power Pro out (I can if need be)
First make sure that you can see your AIU and that its Cab Address is correct. Show Cab will query your Power Cab
Mine is blank because I am in Simulation mode. You should see Cab ID 4 for your AIU
?
?
You stated that you were able to add the Sensor. I used the 4:6 method and giving the name of 4(aiu06).
This is for Panel Editor not Layout Editor it has a different process.
The System Name is generated by JMRI and it will appear in the Add Sensor Panel automatically.
I added 2 indicators and you can see that they both work.
?
?
Layout Editor can give the same symptom but that's because we don't make the Block association assignment.
?
You Right Click on the Track segment select Edit , Create the Block Name ( I used BLK1)
Then make the assignment.
?
?
Once you make the assignments it will display.
?
?
Hopefully this helps
?
Inobu
?
?
?
?
?
|
Looked at it and started to think about to do it, but I found that the SignalPilot has a lot of indexed CVs and, furthermore, there is no documentation about its CVs (all of them) :( , so, unfortunately, more than difficult to do it.
?
Should any one have any information about it, I am ready to help on it, as I already did defining .xml's for including new signals definitions for SignalPilot.
?
Regards
|
Re: After Windows 11 upgrade I can no longer communicate via NCE USB module
#nce
#windows
Bill, ? This log looks normal. I don’t see it showing any issue with opening the port, getting the id from the NCE USB. But what did you have set in the connection window at this time? ? I’m presuming you have both a PowerCab and a SB5 from what you said. The recommended setup for that combination would be using two profiles. One for the PowerCab as the command station so you have a programming track. The second is with the SB5 as the command station so you can move around with the PowerCab as a normal throttle. ? But to do that, I suggest you make a change to the NCE USB. I would use it with all jumpers in place. This is the ‘all systems’ setting. That in turn would mean both profiles are set for 19,200 baud. This way you don’t have to change the jumpers between the two systems. ? But there is a table of the id’s used by the NCE USB and the code cross checks that value with the command station selection. The message you posted would say the selection you had in the connection settings didn’t match the id value returned by the NCE USB. ? I take it that this last run didn’t give you any popup? ? -Ken Cameron, Member JMRI Dev Team
? ?
|
Re: After Windows 11 upgrade I can no longer communicate via NCE USB module
#nce
#windows
Ken,
?
I am currently using 5.11.3, but this problem existed on the prior released version as well.
?
I have a “new” session log attached here for your review. My message log goes back to 2020 so it is much bigger.
?
Thanks,
Bill
?
toggle quoted message
Show quoted text
From: [email protected] <[email protected]>
On Behalf Of Ken Cameron via groups.io
Sent: Saturday, March 08, 2025 7:35 PM
To: [email protected]
Subject: Re: [jmriusers] After Windows 11 upgrade I can no longer communicate via NCE USB module
?
Bill S,
?
Looking deeper into the code, I see I need to know more things. I’ll recap:
- System console so I can see:
- Version of JMRI
- Version returned by the NCE USB
- The logged error message
- NCE command station firmware version id
- That’s either 1.28something or 1.65something.
?
But so far it is looking like you may not have the right jumper settings in the NCE USB and the version ID it is giving doesn’t match what it should be for the SB5 system. But depending on which jumper settings, the baud rate may also need
to change to match what it expects.
?
But with the details above, I can guide the right answers.
?
-Ken Cameron, Member JMRI Dev Team
?
?
?
|
On Sat, Mar 8, 2025 at 10:36 PM, Noel Purdey wrote:
Just wondering, where do I find the ‘track analysis tool’?
?
Dan
|
Hello All
After a year away im back into it,and starting to put layout into jrmi,thanks to all who devolop it.
?
I have added sensors before and had them working but this time not so good
Ihave all? NCE equipment,via usb all good there
?
I have added a basic Layout in Panel Editor ,added turnouts now onto sensors
I open sensor tab,give the sensor a name,in this case 4(aui01)and the input 6.
A green tick appears,but when i activate the sensor nothing shows
What step am i missing.I tried manually setting to active but didnt help.
?
Is it a case of not getting the right info to jrmi?
Thanks for your time
Brett
|
Re: Frequently Asked Questions/Topics/Official Announcements?
Sticky is all very well for people using the group's web interface. I don't, and I'm sure there are many like me who just let the messages arrive in email form, either individually or as digests.
Might be worth a poll.
Personally, I think a faq on the jmri site is a lot more useful, and the standard questions could than be handled with a reply in the form of a single link.
Doing that lists the messages singly, not threaded. Personally, I don't find that a useful format whatsoever.
?
I agree with Andy - Move the stickies somewhere else, maybe leaving one sticky with a pointer to the rest. Some of the sticky content is already duplicated in the Wiki, why not put the rest there? Absolutely none of the other fora I follow, either on or elsewhere, whether MRR related or my other hobbies, are similarly cluttered.
?
Besides, considering some of the posts I've seen (not just here), I doubt many people look at the stickies anyway.
?
Steve
"Breezlys"
?
On Sat, Mar 8, 2025 at 01:58 PM, Peter Ulvestad wrote:
I never see those first.
Change topics to messages and at the top right click on date so it shows the newest messages first.
--
Peter Ulvestad
Linux Mint 22.1, JMRI 5.11.3plus, Java 21.0.5
JMRI Users Group Moderator ( /g/jmriusers )
JMRI Developers Group Moderator ( )
Tam Valley Group Moderator ( )
Sprog-DCC Group Moderator ( )
Edmonton Model Railroad Association ( )
|
Re: Frequently Asked Questions/Topics/Official Announcements?
Doing that lists the messages singly, not threaded. Personally, I don't find that a useful format whatsoever.
?
I agree with Andy - Move the stickies somewhere else, maybe leaving one sticky with a pointer to the rest. Some of the sticky content is already duplicated in the Wiki, why not put the rest there? Absolutely none of the other fora I follow, either on groups.io or elsewhere, whether MRR related or my other hobbies, are similarly cluttered.
?
Besides, considering some of the posts I've seen (not just here), I doubt many people look at the stickies anyway.
?
Steve
"Breezlys"
?
On Sat, Mar 8, 2025 at 01:58 PM, Peter Ulvestad wrote:
I never see those first.
Change topics to messages and at the top right click on date so it shows the newest messages first.
--
Peter Ulvestad
Linux Mint 22.1, JMRI 5.11.3plus, Java 21.0.5
JMRI Users Group Moderator ( /g/jmriusers )
JMRI Developers Group Moderator ( )
Tam Valley Group Moderator ( )
Sprog-DCC Group Moderator ( )
Edmonton Model Railroad Association ( )
|
On 3/8/2025 10:10 PM, Leaving DC behind via groups.io wrote: Ok ladies and gents, I have a layout drawn up and in JMRI. I can pull the panel up use all the turnouts from the panel all this works great. My question after operating on a few different layouts. How do I get the panels to load once I select the profile I want for the panels to come up without having to select the file of the panels. I have the start up instructions set but what am I missing. I’ve seen several iterations once the profile is selected it brings up the panels belonging to that profile without actually having to select the files. Fr a given JMRI profile: "Edit"->"Preferences"->"Start Up". operate the "Add" button, and select "Load table content and panels...". Select the appropriate ".XML" file. "Save" the preferences. (BTW: If you will want to open any of the "Tools"->"Tables" windows as part of the JMRI "Start Up" preferences, be sure to add those windows _after_ loading the "XML" file. Why? If you open any of the "Tables" "windows" before loading the ".XML" file, the display of the table will likely re-sort all of the objects _for each and every object_, which can be very slow. instead, if the objects are loaded first, before the Table's window is opened, the process of opening the window only needs to be "sorted" one time.)
|
Stewart,
The version you showed is the Java version. ?The JMRI version will be 5.something.
Edge Connector "links" are connections between two blocks. ?For example,
Panel 1 :: ?track segment (block A) -> EC [link] EC -> track segment (block Q) :: Panel 2
Dave Sand
----- Original message -----
Subject: [jmriusers] Edge Connectors in Layout Editor. #layouteditor
Date: Saturday, March 08, 2025 9:26 PM
Hi, I am developing two Layout Panels for my two-level layout. I have added an Edge Connector on each Panel for the connecting track between the two panels. When I try to "Edit Link" to connect the Panels, nothing happens. No Dialogue Box appears. Has this occurred to others, and is there a fix? The JMRI version I am using is 17.0.13.
?
Cheers,
?
Stewart
|
Gents, ? Just wondering, where do I find the ‘track analysis tool’? ? I do not seem to be able to find it. ? Noel ?
toggle quoted message
Show quoted text
From: [email protected] <[email protected]> On Behalf Of Dan Boudreau via groups.io
Sent: Sunday, 9 March 2025 7:50 AM
To: [email protected]
Subject: Re: [jmriusers] Track Analysis Tool #operationspro? however I do need to add flatcars and gondolas as they were down below 20% in total of all track types.
Not a good reason to add them.? It only means that your flatcars can only take 20% of the available track space, or 1/5 five cars could be a flatcar going to one of those track types.? I wouldn't change a thing. With regards to boxcars, I agree with you, you might have a few too many!
|
years ago i backed up my PowerPro command station into JMRI ? It copied any macros and other data from the command station to a file in JMRI. Now I can’t find it
Could someone explain the process to backup the command station?
Thanks Jim Little MMR?
|
Hi, I am developing two Layout Panels for my two-level layout. I have added an Edge Connector on each Panel for the connecting track between the two panels. When I try to "Edit Link" to connect the Panels, nothing happens. No Dialogue Box appears. Has this occurred to others, and is there a fix? The JMRI version I am using is 17.0.13.
?
Cheers,
?
Stewart
|
Ken Cameron