开云体育

I have opened issue #11982 in JMRI's source repository to cover this problem.

Then I wonder why all the "Read" buttons on the decoder page are grayed out. My JMRI is 5.3.3 on Windows 10 wiht Java 11.0.14. Anyone have an idea why that might be?

Scott Walton

I found out right away that I couldn't think of individual items like blocks, signaling, detection, and power feed.
They are all part of a system.

Start out with turnout protection.?
Signals are needed (either real or virtual) on each leg.
Signals reside (usually) at block boundaries.
Some of my turnout track work are close and I consider that set of turnouts as one structure. (think 3-way)
When you run automation, each turnout needs to be a block.
If you plan to detect the turnout, gap each leg.
I didn't burn a detector channel, so I simulated the turnout occupancy (it's tricky)
Sometimes, I seriously thought of detecting certain turnouts.
Generally, you'll assign a JMRI block to an electrical block and detect on the feed.

I use JMRI mast logic, but plan your signals now regardless of signal system you use.
For the time begin you and run automation without signals.
I ran my automation with virtual signals until I installed hardware.

Like carpentry - measure twice cut once - plan twice then build.

--
Ken
NYNH&H, Old Colony Division, Cape Cod Branch (1949-1959)
[DB150][PR3][QuadLN_S][JMRI 5.3.5]

Dear testers,

I have just downloaded the current test version of JMRI as you can see by the title. ?I have had a look to see what ‘Cabs’ are on my NCE Powercab handset and can only set the current cab in use. ?Is it possible to show more cabs on a single handset please as I can RECALL upto 6, thank you.?

Kind regards
Duncan Hamilton

Scott
Using Roco I can read all / read sheet, but, I cannot read any indexed CV.
Steve G.

What determines the position and size of windows in jmri? At some point the positions and sizes were recorded. Now no matter how much I reposition and resize windows, saving using "store all tablets content and panels", nothing changes and remains with some past definition

Good morning,
I am in the planning stages of my layout. I am currently trying to figure out where I need to place my "blocks".
I am using all Digitrax hardware including a Digitrax BXP88 for power management and also block occupancy detection. I believe the BXP88
reports block occupancy status to LocoNet. I'm also using Peco ElectroFrog turnouts. I've watched some videos on youtube
and I'm thinking of setting up my Peco ElectroFrog turnouts so that each one of those turnouts is it's own individual block. I'm planning to use JMRI software
for running my layout and someday maybe CATS software. Someday I plan on adding signals to my layout. I believe there are a couple
of different ways of wiring up the Peco ElectroFrog turnouts. So should I plan on setting up my turnouts so that each one of them is it's own block?
What do you guys think? Is that the best plan?
Thanks,
Tim

--
MARK TAYLOR

I followed this discussion and was triggered by the comment that you can set the number of 'send counts' to a mast.
I know you can set that for a turnout, but for a mast I haven't been able to find that setting anywhere.
What am I missing?

?

--
Douwe

Since this is a decoder issue and not JMRI you should take your questions to the TCS group.
/g/TCS-Users

--
Peter Ulvestad

JMRI Users Group Moderator ( )
Tam Valley Group Moderator ( )
Sprog-DCC Group Moderator ( )
Edmonton Model Railroad Association ( )

Good morning Mark,
I have 3 TCS WOW-121 Steam Decoders. I think they are very similar. Sometimes hickups can happen on the rails
and the decoders can sometimes interpret them as programming commands. I have been "LOCKING" all of my TCS WOW-121 Steam Decoders.
That way they are locked and will NOT accept any programming commands. When the time comes and you want to make programming changes
to the decoders you can then unlock them to make the CV changes. I know this doesn't exactly answer your question right now
but it might avoid some future problems down the road.



Good luck!
Tim

Hello group.
I have a question about this decoder. I have 2 GP38's that are consisted together. I have not run these 2 locos for a week or so.
--Today when I started to run this consist the locos ran for about 15 seconds and the one loco stopped moving. Before it stopped there was a beeping sound for about 5 seconds. When I turn the throttle to 0 and then turn the throttle up again the loco that beeps and stopped, now sounds like a brake release and starts moving again. Then about 15 seconds later it beeps and stops.
I use JMRI for programming and these two locos are programmed the same. They have been running together for 3 years.
Seems strange how this happened.
Any thoughts would be appreciated.

Thanks,
MARK TAYLOR

On Mon, May 1, 2023 at 07:33 AM, <stephenjohnson500@...> wrote:

I'll give that new version of the sketch a go when I get back from work tonight. If it is okay, which I'm sure it will be, then is it possible to modify it for the PN532 readers? There is a slight problem with the existing PN532 sketch, but I was waiting to get the MFRC522 Ethernet/Serial sketch sorted first.?

I can then try the two Ethernet Uno's with different readers as network connections into JMRI and see how that goes.

Steve,

I have a jumpstart already on the PN532 version, so yes, we can tackle the Ethernet/Serial version of that one next! :-)


Tom

Try only printing the 1st page when the printer popup window appears.? If that doesn't work, print to pdf, and only print the 1st page.

Thanks I went there but it won’t let me print just this page even though I select to print inly on this page. It will only print 16 pages, which includes all the train info for all trains listed. I just need the train list sheet.?

What am I missing?

thanks,
frank
--

Gentlemen,?
--
Sent from my gosh darn droid!
Please excuse the fat finger mistakes...
John

Ethernet/Serial

Tom

I'll give that new version of the sketch a go when I get back from work tonight. If it is okay, which I'm sure it will be, then is it possible to modify it for the PN532 readers? There is a slight problem with the existing PN532 sketch, but I was waiting to get the MFRC522 Ethernet/Serial sketch sorted first.?

I can then try the two Ethernet Uno's with different readers as network connections into JMRI and see how that goes.

Steve