¿ªÔÆÌåÓý

  1. Jmriusers
  2. Messages
Expanded Topics Messages Polls
Date
Locked Re: Clarifying expection

[email protected]
 

Phil,? I see you posted you attachement as a Photo in Photos

IB are internal blocks, and I believe? not physical blocks on the layout or test track.? So you must trip these manually unless the IB1, IB3 have sensors attached to them.

Usually those physical to layout blocks would have LB (if Loconet)? or NB (If NCE).

Marc?
Locked Re: Dec. Pro (4.18) and Easy DCC #easydcc

[email protected]
 

Cleaning the track before doing any programming is a recommended. The small currents, time factors and small contact patches involved require perfect conditions.

But " error reading " is totally different error than? " no ports found ".

Marc
Locked Re: Dec. Pro (4.18) and Easy DCC #easydcc

 

Thanks to all. ?I had copied a 20 Loco roster from Dec. Pro 4.10 to a newer computer running 4.18.
I just wanted to "Read from the Decoder" to confirm that this version was working well for me.
I established the correct Com port and now I'm OK but special thanks to Edward Klein. ?
I more thoroughly cleaned the?programming track ?and 4.18 is working well.

Regards,
Ed Woz.
Locked Re: Program stalls.

 

I concur, I have Windows 10 and never let it go into sleep mode while JMRi is running or at all, and always?shut down
JMRI when leaving computer for any length?of time. I have had terrible things happen when this is ignored.

Bob Campisi

On Sat, Feb 8, 2020 at 12:06 PM dick bronson via Groups.Io <dick=[email protected]> wrote:

PJ,

You have not given us anything to work with, but one common issue is that Windows will disconnect the serial ports if it goes to sleep. JMRI does not know how to get them going again when Windows wakes up again. The answer is simple. Don't do that. I.e. don't let Windows shut down when there is no activity, or at least set the time before snoozing to a long time with no activity.

Dick :)

On 2/8/2020 9:26 AM, whmvd wrote:
PJ,

Please also elaborate as much as you can on what you mean when you say 'stalling'. Is it slowing down? If so: WHAT is slowing down? Is it stopping completely? If so: is that sudden or is response (in controlling a train or maybe a panel) getting progressively slower before grinding to a halt?

We must seem a collection of pedants, but, really, getting to grips means getting as clear an idea on what goes on as you can possibly give.

Wouter

On Sat, 8 Feb 2020 at 12:45, Phil in gorgeous Young Harris via Groups.Io <philabernathy=[email protected]> wrote:
PJ, I'm afraid that the description and details are too vague to get a specific answer.? I suspect that troubleshooting will have to involve changing things on that computer such as scripts or panels that are run from the start.?

For example, I suspect that "runaway" scripts with endless loops are the most common issue of a working JMRI that seems to be "stalling" but really, is just too busy to take input from you.? Really bad endless loops can overflow the memory on the computer and actually lock up the computer too.? I have not seen Logix cause that issue, but I have not seen it all, and am not an expert in that.

Phil in gorgeous Young Harris, Georgia, USA

Locked Re: Program stalls.

 

¿ªÔÆÌåÓý

PJ,

You have not given us anything to work with, but one common issue is that Windows will disconnect the serial ports if it goes to sleep. JMRI does not know how to get them going again when Windows wakes up again. The answer is simple. Don't do that. I.e. don't let Windows shut down when there is no activity, or at least set the time before snoozing to a long time with no activity.

Dick :)

On 2/8/2020 9:26 AM, whmvd wrote:

PJ,

Please also elaborate as much as you can on what you mean when you say 'stalling'. Is it slowing down? If so: WHAT is slowing down? Is it stopping completely? If so: is that sudden or is response (in controlling a train or maybe a panel) getting progressively slower before grinding to a halt?

We must seem a collection of pedants, but, really, getting to grips means getting as clear an idea on what goes on as you can possibly give.

Wouter

On Sat, 8 Feb 2020 at 12:45, Phil in gorgeous Young Harris via Groups.Io <philabernathy=[email protected]> wrote:
PJ, I'm afraid that the description and details are too vague to get a specific answer.? I suspect that troubleshooting will have to involve changing things on that computer such as scripts or panels that are run from the start.?

For example, I suspect that "runaway" scripts with endless loops are the most common issue of a working JMRI that seems to be "stalling" but really, is just too busy to take input from you.? Really bad endless loops can overflow the memory on the computer and actually lock up the computer too.? I have not seen Logix cause that issue, but I have not seen it all, and am not an expert in that.

Phil in gorgeous Young Harris, Georgia, USA

Locked Re: Program stalls.

Jon Miller
 

¿ªÔÆÌåÓý

On 2/8/2020 9:17 AM, PJ via Groups.Io wrote:
At this time it will now work again for a couple hours. -- This never happens on my computer on my layout. The programming is the same on both.

??? If everything is identical on both computers I would blame the computer!

-- 
Jon Miller
For me time stopped in 1941
Digitrax  Chief/Zephyr systems, JMRI User
SPROG User
NMRA Life member #2623
Member SFRH&MS
Locked Re: Operations manifest printing #operationspro

 

Hi Phil,
It is an older Acer laptop with Windows 10 Home installed.
The default printer is shown as the TS6120.?? The same port is being used for all the printer jobs.

I just selected preview, clicked on preview and was able to print the manifest from that window.
I then unchecked preview, clicked on the print button and it just hung again.?? Print queue showing printer is connected and printing through the same port as the other print jobs.

Not a big problem, as I can work with it using the checked preview box and printing from preview.
It's just that when terminate a warning comes up that the manifest hasn't been printed.
I just click yes and carry on.??? Seems to work fine using this system.
Locked Re: Operations Feature Request #operationspro

 

Thanks Dennis,
I didn't realize the DS and Clerk were in two different locales around here we don't have the luxury of having that many operators. If we can get the feature without it being mandatory for operations it sounds like a good idea.One of the problems I run into when teaching someone new is trying to get them to start simple then go for the neat stuff after they learn the basics. The most of the calls I get is from newbies wanting to run schedules, alt. tracks and some of the other things that are great about this program when they have never even built a single train. The biggest thing we as experienced operators with JMRI is to teach the newbies is the KISS method and help them to get up and running before taking them off the deep end of the pool. I think it would be great if we had weekly or so online training course to help newbies learn the program from simple data entry to the complex componets in scheduling and other ideas. I have been fooling around with JMRI for 10 years or so and still am learning new things all the time. I for one would welcome beginer and advanced seminars on JMRI at conventions and train shows. Here in Nebraska we are scattered all over the place and far apart we learn online but sometimes we just have to go hands on in person.
?Sorry this rambles.
Just my thoughts helping newbies and experienced operators with JMRI
This is a great program, Thanks
Matt Greenwood
Cascade Rwy
Grant NE?
Locked Re: Program stalls.

 

By stalling I mean it freezes. I put the mouse on a switch to turn it and nothing happens. I try to bring the main menu up to shut down and nothing happen. I have to shut the computer down wait 10 or so seconds, restart the computer and the restart the Panel Pro. At this time it will now work again for a couple hours. It¡¯s frustrating during an op session. This never happens on my computer on my layout. The programming is the same on both.

PJ
Locked Re: Setting Max Speed on Broadway Limited & Digitrax N Scale Decoders

[email protected]
 

Yes I agree, too many variables, too? vague,? and not really a JMRI issue. ?

Marc?

Locked Re: Can't load JMRI4.18 on Windows 10 Laptop #windows10 #4-18

[email protected]
 

Other possible is do not try the update while there is a running copy of JMRI or you will get this message.

A? anti-virus app has a "quarantine" where downloaded, un-trusted apps, are placed.? Find it and tell the Anti-virus you trust the app in question.? OR wait for the next update of you Anti-Virus app.

Marc
Locked Re: Clarifying expection

 


Thank you


On Sat, Feb 8, 2020 at 11:04 AM Peter Ulvestad <ulvestad@...> wrote:
Attachments are not allowed.
You can create a folder within the "Problems Being Worked On" folder of the files section and upload your attachment there.

--
Peter Ulvestad

JMRI Users Group Moderator - ( )
Tam Valley Group Moderator - ( )
Sprog-DCC Group Moderator - ( )
Edmonton Model Railroad Association -



Locked Re: Clarifying expection

 

Attachments are not allowed.
You can create a folder within the "Problems Being Worked On" folder of the files section and upload your attachment there.

--
Peter Ulvestad

JMRI Users Group Moderator - ( )
Tam Valley Group Moderator - ( )
Sprog-DCC Group Moderator - ( )
Edmonton Model Railroad Association -

Locked Clarifying expection

 

¿ªÔÆÌåÓý

I am a new user.

The train instruction below should have train 10 move from block 1 to block 3 and reverse to block one correct?

Because it just continued around my test loop.? What am I missing.

?

?

Sent from for Windows 10

?
Locked Re: Can't load JMRI4.18 on Windows 10 Laptop #windows10 #4-18

[email protected]
 

Maybe try to run? the installation as administrator?
Locked Re: Block detection

 

Skip,

jmri.Block

If you are asking about OBlocks: jmri.jmrit.logix.OBlock.


Dave Sand

?

----- Original message -----
From: "Andrew Vandermolen via Groups.Io" <Skipvdmolen@...>
Subject: [jmriusers] Block detection
Date: Saturday, February 08, 2020 9:16 AM

Is there a Class to check the status of a block? I know of the Wait for occupancy.?
TIA
Skip V

Locked Block detection

 

Is there a Class to check the status of a block? I know of the Wait for occupancy.?
TIA
Skip V
Locked Re: New JMRI Version breaks my panels #4-18

 

Bob,

Excellent.

Now create a zip file of?C:\Users\Conemaugh\JMRI and upload the zip file. ?I should be able to re-construct your environment from the zip file.

Dave Sand



----- Original message -----
From: rzeollaorcl <robert.zeolla@...>
Subject: Re: [jmriusers] New JMRI Version breaks my panels #4-18
Date: Saturday, February 08, 2020 8:06 AM
Locked Re: Panel Editor - Signal Heads not able to be Dragged and Dropped from Palette #paneleditor

Bob England
 

¿ªÔÆÌåÓý

Dave

?

That is good news!? Let me know what you find as the only thing I can figure out to fix this is to manually replace in the layout XML file all the signal head icons that have ¡°<incons />¡±, with any changes to the signal head icon being done manually too.

?

Keep us posted.

?

Thanks.

?

BobE

?

From: [email protected] [mailto:[email protected]] On Behalf Of Dave Sand
Sent: February 07, 2020 11:42 PM
To: [email protected]
Subject: Re: [jmriusers] Panel Editor - Signal Heads not able to be Dragged and Dropped from Palette #paneleditor

?

Bob, Cliff,

?

I believe I have found the bug that causes the lack of image icons for signal heads. ?Since I rarely work in the Control Panel Editor code, I need to do more research to confirm my findings.

?

Dave Sand

?

?

----- Original message -----

From: Bob England <rje.bob@...>

Subject: Re: [jmriusers] Panel Editor - Signal Heads not able to be Dragged and Dropped from Palette #paneleditor

Date: Friday, February 07, 2020 10:16 PM

?

DaveS / DaveH

?

Thanks very much for your comments.? Between your thoughts and CliffA's comments, I was able to migrate the icons.? The "Preferences" option did not show up previously, but when I physically deleted from the program directory the icon files, it showed up when JMRI asked what icon file to point to when it could not find the old file.? I've restructured the layout file with the icons on my J: directory.

?

Signal head icons are all still wonky, but at least now I?have the icon files in the proper place.

?

Thnks guys!

?

BobE

?
Locked Re: Can't load JMRI4.18 on Windows 10 Laptop #windows10 #4-18

 

Thank you for the suggestions!

Jack
71761 - 71780 of 240323