Thanks Marc,

I am set up in Stand alone mode, my lights seem to work as you described. I may be wrong but I had all the cables in the same box and only had one power supply for my DCS 52, which I run independently from the system. On the PR3 I have two wires hooked directly to the test track and run a USB to the computer (thats it) which I am assuming after reading is my issue, although as I said before, these are the same cables I had it set up with originally. I have never has a serial adaptor, so I am going to assume that is the solution even though it worked with these cables before. ( I have several dozen locos set up in the roster that I programmed using this cable.

Also, if running as Stand Alone, in configuration I have the system connection set to Loconet PR3, the serial port is correct ?(cu.usbmodem1421), command station type is PR3 Stand alone programmer, conn prefix is L, connection name is Loconet.

I am unfamiliar with a system console log or where to access it.

Getting ready to ditch the Mac and grab a pc...

Thanks again,

Craig

That is not a JMRI version issue, that is an "OPPS" on the part of the author of the definition file who added the TSU2 2200.? He mistakenly used those from the ELECTRIC and that is why you see pneumatic doors and pantograph.

Marc

开云体育

Bill,

4.16 will cause you troubles with a LocoBuffer-USB. Upgrade to 4.17.4 or wait for 4.17.7 due out very soon now. (don't use 4.17.5 or 4.17.6 either) I'm not saying that this is the cause of your Tsunami issue, but 4.16 might not even be communicating with the command station.

Dick :)

I just downloaded version 4.16 (Windows 7, Loco Buffer-USB) and trying to program a Tsunami2 steam 2200.? How come the NMRA legacy function map does not match that shown in the Soundtraxx manual?? The map in Decoder Pro looks more like that for a non-steam loco.

Thanks,
Bill Darnaby?

Dave,

Thanks for your help

I'll try reinstating Sections, Transits and dispatcher, change the colour of my tracks, and upload the xml if it still doesn't work.

I probably ought to do some research on US signalling practice, I'm more used to European systems.

Alasdair

System Details:
MERG CBUS using CANUSB for infrastructure control
Lenz LZ100 via Lenz USB to run trains
I'm using resistive wheelsets and block occupancy detection
Points are all SEEP solenoid motors, providing frog switching, but no feedback

I was looking for some advice, on how best to automate my layout.

I've drawn up the railway in layout editor, and linked up the block sensors and points. Currently all signals are imaginary (JMRI internal only) using signal masts at block boundaries.The switches all throw correctly from the Turnout list or by clicking on the diagram symbol. The signals work correctly based on track occupancy and switch settings, but I'm struggling to get automation working. My questions are:
1. Should I be trying to use transits and dispatcher, or NX routing, or warrants, or something else?
2. I've tried using NX routing but it wont set the switches - any ideas why?
3. When I tried using dispatcher, it didn't like driving the trains in auto (Throttle window appears, can drive manually, but auto has zero speed) - any idea why?
4. How do I change the colour of a track section from white when it is reserved for a route? with a white background to the panel, the track just dissapears!

Many thanks
Alasdair

Thanks for that Perry.

Has been updated now and will usually be incorporated in the next Production release.

If you're interested, you can follow the process of this getting into JMRI on GitHub at?

Best regards,

Matt H

Note: the web client does support each block using different colors; you may be able to use that to further distinguish your tracks.

It’s on my to-do list… but pretty far down… :(
The panel.js file need some major refactoring… but without any way to write test cases it’s very fragile… at the very least I’d like to see it use TypeScript over JavaScript… but that’s going to require someone with build mojo (not me).
On the plus side I did add decorations support! The web client now supports arrows, bridges, end bumpers and tunnels! ;-)

The Signal Mast Repeaters section in the documentation has a typo on line 2 that says, " ..., and van be set as Slave, ...", instead of, "..., and can be set as Slave,...). The bold face added by me to identify needed change. ?The documentation could use ?the addition of a statement that indicates that the Signal Masts must be Stored prior to attempting use of the Repeaters tool.
?

Hi Dave, Looks useful, thanks for the help. However I am not familiar with Java and cannot find the Jython folder on my Mac, do I need to run another programme to set it up? When I follow your instructions and "Run Script" the Jython folder comes up with a list of scripts. I obviously have to get your script in that folder but cannot find it!

Hey everyone?
I am trying to create a layout and trying to get multiple blocks on layout editor controlled by one single sensor how do I do this.?

thsnks Tim

Hi, i am looking for a way to tell when a train has actually stopped through issuing throttle.setSpeedSetting(0) or has reached the actual setting issued through issuing the command?throttle.setSpeedSetting(0.4) for example. Is this possible?

Thanks Jim

开云体育

Had this happen to me the other night. Had 4.17.6 and 4.17.1 installed on system, one as "This user only" and other
" for all Users" .. Apps& features showed a single instance of JMRI? but I had multiple icons on desktop. When I removed/Uninstalled JMRI 4.17.6, the App&features then showed a JMRI 4.17.1 as present ? and I could not remove it.? Going thru registry cleared up that mess.

Layout Editro in Edit Mode

Layout Editor in Non-Edit Mode