开云体育

Dave that's not the issue when i click on the reset button i get an error message "Unknown Error 307" so it doesn't do the write Terry Visit My Web site@ http://conewriversubdivision.yolasite.com/

After sending the reset value, doesn't power have to be removed from the decoder by tilting the engine? David Klemm Sent from my iPhone 7 Plus ________________________________ Sent: Thursday, July 27,

I have no problem programming other CVs it just won't do a reset The power pax is working fine Peter I took the locos to my work bench where i have my old Zephyr DCS50 and used blast mode there to

In a message written on Wed, Jul 26, 2017 at 05:34:22PM +0000, stevedavis@... [jmriusers] wrote: That's fascinating. I'm not saying it's impossible, but I beat one up pretty bad and

Does it work using JMRI with the zephyr in blast mode? Or in regular mode without the power pax? Power Pax are unreliable, my club tried 2 with no luck and now we exclusively use Soundtraxx PTB-100s.

Billybob, Thank you. I have spent a lot of time in vain searching through the JMRI documents to attempt to find a way to turn this functionality off. At least I don't need to keep searching! I may be

JMRI will only bridge the events you place logic to connect them. Each connection is treated as separate. So a Logix that watch a sensor on one connection could then drive a turnout or sensor on the

Jeff, Normally I find a finger across the rails will trip the detector, sometimes needing to be slightly wet. -Ken Cameron, Member JMRI Dev Team www.jmri.org www.fingerlakeslivesteamers.org

Steve, This behavior is likely entirely consistent with JMRI's basic behavior for JMRI "signal heads" which are configured as controlled by an SE8c. JMRI does not have support for any SE8c mode other

I have hooked up a CT-detector ( RR-Cirkits ) to a watchman board. The detector is monitoring a power wire off the PSX to the track. Is there a way of testing the detector with a meter....???? Thanks

Ok Dave. Thanks. Donald Dillaby 27 Palisade Dr Nashua, NH 03062-2119 603-888-2766 603-305-5523 Sent: Thursday, July 27, 2017 1:37 PM To: jmriusers@... Subject: [jmriusers] Re: JMRI 4.8 is

Donald, No. The file I modified for was an appearance file for SPTCO-1930 signal system. Those changes are included in 4.8. Dave Sand

Hi I upgraded to v4.8 but ever since have not been able to get my control panel to load without using TurnOffXmlValidation.py in the startup folder. the error message says Exception:

Hello, I have experienced this "problem" in 4.5.x. I did some searching within this forum and read that this problem might be resolved in 4.7.1, so I upgraded to 4.7.1 Still getting errors (see

Bob, At the NMMRC, I upgraded our 2 PCs last night to 4.8. Initial test last night show all is well. PC1 is our programming track PC where we just use decoder pro. That one had 4.5.2 prior to the

Dave: Is that the file you modified for me for use with JMRI 4.6? I have yet to download version 4.8. Donald Dillaby 27 Palisade Dr Nashua, NH 03062-2119 603-888-2766 603-305-5523 Sent: Thursday, July

Fraser, With 4.8 installed, search your ENTIRE machine for file name signalmasts-2.9.6.xsd The number of lines in the file should be around 406. If you have more than 1 file, you have another JMRI

Just upgraded to Production Version 4.8 all works ok except as in the past i still can't do a reset on a TCS Wow Decoder I tried a Wow version 2 on my programing track Using my DC51 Zephyr and my

Rodney, I realize you're the author of CATS and not JMRI, but I have to admit I'm stumped here. I don't have any of the Software Flash boxes checked within CATS, and I can't figure out where in JMRI I

Hi Egbert That "MT " that you found is exactly the same as that found by Dave Sand a couple of days ago. I removed it then and that changed the line number of the "Outputs" error when loading. I