Re: i can not get my radio in to adjustment mode
ok thanks, as it is still working , would it be a good idea to put some compound on it, as a lot have gone bad,
thanks Dave
|
Re: i can not get my radio in to adjustment mode
Many of the driver boards have either no or very little heat sink compound on them.?
Be careful with the board as they are no longer available.?
|
Re: i can not get my radio in to adjustment mode
Ok I have got some more info civ and cive go to pins 9+10 of J2252 of the logic unit, so testing from remote jack plug, the civ does connect to pin 9 , but on pin 10 the connection is lost from cive, there are some small inductors between the civ socket and the j2252 connector, I will have to lift the main PCB and have a look, Thanks Dave I will keep you posted
On Mon, 18 Apr 2022, 13:32 davebb123456 via , <davidbrowne76= [email protected]> wrote: Hi also it looks like there is no heat sink compound on the pa driver board , I see this is very common ,as on TRX bench YouTube channel,so I may as well do this while I am in the radio, I have also found some solder balls rolling about the pa board, and I have cleaned a lot of flux off, I see to remove the pa board I have to un-solder the driver board, is there anything that I am missing,I do have all of the correct equipment and knowledge to do this, Thanks Dave 2E0DMB
On Mon, 18 Apr 2022, 00:49 John Mardock, < j@...> wrote: With power off, remove the covers and with a multimeter check to make sure the PCB lands associated with that jack are actually shorted. I have seen dirty/contaminated/corroded jacks. Have also seen the jacks break the connections at the PCB ie land to run.?
Alternately you might try applying a small amount of contact cleaner to the plug and exercising the plug/jack interface.
GL
John
|
Re: i can not get my radio in to adjustment mode
Hi also it looks like there is no heat sink compound on the pa driver board , I see this is very common ,as on TRX bench YouTube channel,so I may as well do this while I am in the radio, I have also found some solder balls rolling about the pa board, and I have cleaned a lot of flux off, I see to remove the pa board I have to un-solder the driver board, is there anything that I am missing,I do have all of the correct equipment and knowledge to do this, Thanks Dave 2E0DMB
On Mon, 18 Apr 2022, 00:49 John Mardock, < j@...> wrote: With power off, remove the covers and with a multimeter check to make sure the PCB lands associated with that jack are actually shorted. I have seen dirty/contaminated/corroded jacks. Have also seen the jacks break the connections at the PCB ie land to run.?
Alternately you might try applying a small amount of contact cleaner to the plug and exercising the plug/jack interface.
GL
John
|
Re: i can not get my radio in to adjustment mode
Hi John I am going to test for any resistance on the remote socket, what is the best way to get to the solder points of this socket, do I remove the top board, or is it from the bottom side of the radio, Thanks Dave
On Mon, 18 Apr 2022, 10:51 davebb123456 via , <davidbrowne76= [email protected]> wrote: Hi John you are thinking the same as me, yes I used contact cleaner on the plug, The civ works with ham radio deluxe, but I will open the radio and look if it is showing as a short, Like you?said there maybe some resistance, Thanks Dave
On Mon, 18 Apr 2022, 00:49 John Mardock, < j@...> wrote: With power off, remove the covers and with a multimeter check to make sure the PCB lands associated with that jack are actually shorted. I have seen dirty/contaminated/corroded jacks. Have also seen the jacks break the connections at the PCB ie land to run.?
Alternately you might try applying a small amount of contact cleaner to the plug and exercising the plug/jack interface.
GL
John
|
Re: i can not get my radio in to adjustment mode
Hi John you are thinking the same as me, yes I used contact cleaner on the plug, The civ works with ham radio deluxe, but I will open the radio and look if it is showing as a short, Like you?said there maybe some resistance, Thanks Dave
On Mon, 18 Apr 2022, 00:49 John Mardock, < j@...> wrote: With power off, remove the covers and with a multimeter check to make sure the PCB lands associated with that jack are actually shorted. I have seen dirty/contaminated/corroded jacks. Have also seen the jacks break the connections at the PCB ie land to run.?
Alternately you might try applying a small amount of contact cleaner to the plug and exercising the plug/jack interface.
GL
John
|
Re: i can not get my radio in to adjustment mode
With power off, remove the covers and with a multimeter check to make sure the PCB lands associated with that jack are actually shorted. I have seen dirty/contaminated/corroded jacks. Have also seen the jacks break the connections at the PCB ie land to run.?
Alternately you might try applying a small amount of contact cleaner to the plug and exercising the plug/jack interface.
GL
John
|
Re: i can not get my radio in to adjustment mode
Hi Paul Yes I have been holding those buttons down when switching on , as in the service manual, Thanks Dave, all help is?appreciated,
On Sun, 17 Apr 2022, 21:56 Paul Hansen, < pwhansen@...> wrote:
Not only does CI-V have to be
shorted, you have to hold down the Pre Amp and Tuner buttons simultaneously
with turning it on. The 7000 is a difficult radio to work on in the adjustment
mode so good luck.
?
Thank You
?
Paul W. Hansen, W6XA
Amateur Radio Service
2134 Carthage Road
Tucker, GA 30084
(864) 222-3539
?
?
I guess that if there is something amiss in the initial programming of the
radio then resetting it will not rectify the problem.
Hoffy
On 18/04/2022 5:53 am, davebb123456 wrote:
I have done a full reset,
?
Sorry Dave, I hope that somebody has the right answer for you. I wonder if
there is some sort of programming /software glitch in the radio.
Once again I wish you all the best.
Hoffy - VK4OY
On 18/04/2022 5:38 am, davebb123456 wrote:
Hi?
?A 3.5mm mono jack plug ,so only 2 pins to short,?
I have used this plug for cat control, with this radio and
ham radio deluxe,
So I don't know why it will not go into adjustment mode,
?
Hi Dave, Hoffy here, just double checking that the 1/8th plug that you are
using has been "shorted" as per the instruction of the manual.
Cheers and all the best,
Hoffy - VK4OY
On 16/04/2022 5:37 am, davebb123456 wrote:
i can not get my radio in to adjustment mode, am i doing
something wrong, i have a uk (10) model , i am doing as page 16 of the service
manual says,and the radio just starts up as normal, my civ port is working and
i am using the same jack plug to try and get the radio in to adjust mode,
Please help,
Thanks Dave 2E0DMB
?
|
Re: i can not get my radio in to adjustment mode
Not only does CI-V have to be
shorted, you have to hold down the Pre Amp and Tuner buttons simultaneously
with turning it on. The 7000 is a difficult radio to work on in the adjustment
mode so good luck.
?
Thank You
?
Paul W. Hansen, W6XA
Amateur Radio Service
2134 Carthage Road
Tucker, GA 30084
(864) 222-3539
www.amateurradioservice.com
?
toggle quoted message
Show quoted text
From: [email protected]
[mailto:[email protected]] On Behalf Of Hoffy
Sent: Sunday, April 17, 2022 15:58
To: [email protected]
Subject: Re: [ic7000] i can not get my radio in to adjustment mode
?
I guess that if there is something amiss in the initial programming of the
radio then resetting it will not rectify the problem.
Hoffy
On 18/04/2022 5:53 am, davebb123456 wrote:
I have done a full reset,
?
Sorry Dave, I hope that somebody has the right answer for you. I wonder if
there is some sort of programming /software glitch in the radio.
Once again I wish you all the best.
Hoffy - VK4OY
On 18/04/2022 5:38 am, davebb123456 wrote:
Hi?
?A 3.5mm mono jack plug ,so only 2 pins to short,?
I have used this plug for cat control, with this radio and
ham radio deluxe,
So I don't know why it will not go into adjustment mode,
?
Hi Dave, Hoffy here, just double checking that the 1/8th plug that you are
using has been "shorted" as per the instruction of the manual.
Cheers and all the best,
Hoffy - VK4OY
On 16/04/2022 5:37 am, davebb123456 wrote:
i can not get my radio in to adjustment mode, am i doing
something wrong, i have a uk (10) model , i am doing as page 16 of the service
manual says,and the radio just starts up as normal, my civ port is working and
i am using the same jack plug to try and get the radio in to adjust mode,
Please help,
Thanks Dave 2E0DMB
?
|
Re: i can not get my radio in to adjustment mode
I guess that if there is something amiss in the initial
programming of the radio then resetting it will not rectify the
problem.
Hoffy
On 18/04/2022 5:53 am, davebb123456
wrote:
toggle quoted message
Show quoted text
I have done a full reset,
Dave
Sorry Dave, I hope that somebody has the right answer for
you. I wonder if there is some sort of programming
/software glitch in the radio.
Once again I wish you all the best.
Hoffy - VK4OY
On 18/04/2022 5:38 am, davebb123456 wrote:
Hi?
Yes yes it is
?A 3.5mm mono jack plug ,so only 2 pins
to short,?
I have used this plug for cat control,
with this radio and ham radio deluxe,
So I don't know why it will not go into
adjustment mode,
Thanks Dave
Hi Dave, Hoffy here, just double checking that
the 1/8th plug that you are using has been
"shorted" as per the instruction of the manual.
Cheers and all the best,
Hoffy - VK4OY
On 16/04/2022 5:37 am, davebb123456 wrote:
i can not get my radio in
to adjustment mode, am i doing something wrong, i
have a uk (10) model , i am doing as page 16 of
the service manual says,and the radio just starts
up as normal, my civ port is working and i am
using the same jack plug to try and get the radio
in to adjust mode,
Please help,
Thanks Dave 2E0DMB
?
|
Re: i can not get my radio in to adjustment mode
I have done a full reset, Dave
Sorry Dave, I hope that somebody has the right answer for you. I
wonder if there is some sort of programming /software glitch in
the radio.
Once again I wish you all the best.
Hoffy - VK4OY
On 18/04/2022 5:38 am, davebb123456
wrote:
Hi?
Yes yes it is
?A 3.5mm mono jack plug ,so only 2 pins to
short,?
I have used this plug for cat control, with this
radio and ham radio deluxe,
So I don't know why it will not go into
adjustment mode,
Thanks Dave
Hi Dave, Hoffy here, just double checking that the 1/8th
plug that you are using has been "shorted" as per the
instruction of the manual.
Cheers and all the best,
Hoffy - VK4OY
On 16/04/2022 5:37 am, davebb123456 wrote:
i can not get my radio in to
adjustment mode, am i doing something wrong, i have a uk
(10) model , i am doing as page 16 of the service manual
says,and the radio just starts up as normal, my civ port
is working and i am using the same jack plug to try and
get the radio in to adjust mode,
Please help,
Thanks Dave 2E0DMB
?
|
Re: i can not get my radio in to adjustment mode
Yes that's what I am thinking, Thanks Dave
Sorry Dave, I hope that somebody has the right answer for you. I
wonder if there is some sort of programming /software glitch in
the radio.
Once again I wish you all the best.
Hoffy - VK4OY
On 18/04/2022 5:38 am, davebb123456
wrote:
Hi?
Yes yes it is
?A 3.5mm mono jack plug ,so only 2 pins to
short,?
I have used this plug for cat control, with this
radio and ham radio deluxe,
So I don't know why it will not go into
adjustment mode,
Thanks Dave
Hi Dave, Hoffy here, just double checking that the 1/8th
plug that you are using has been "shorted" as per the
instruction of the manual.
Cheers and all the best,
Hoffy - VK4OY
On 16/04/2022 5:37 am, davebb123456 wrote:
i can not get my radio in to
adjustment mode, am i doing something wrong, i have a uk
(10) model , i am doing as page 16 of the service manual
says,and the radio just starts up as normal, my civ port
is working and i am using the same jack plug to try and
get the radio in to adjust mode,
Please help,
Thanks Dave 2E0DMB
?
|
Re: i can not get my radio in to adjustment mode
Sorry Dave, I hope that somebody has the right answer for you. I
wonder if there is some sort of programming /software glitch in
the radio.
Once again I wish you all the best.
Hoffy - VK4OY
On 18/04/2022 5:38 am, davebb123456
wrote:
toggle quoted message
Show quoted text
Hi?
Yes yes it is
?A 3.5mm mono jack plug ,so only 2 pins to
short,?
I have used this plug for cat control, with this
radio and ham radio deluxe,
So I don't know why it will not go into
adjustment mode,
Thanks Dave
Hi Dave, Hoffy here, just double checking that the 1/8th
plug that you are using has been "shorted" as per the
instruction of the manual.
Cheers and all the best,
Hoffy - VK4OY
On 16/04/2022 5:37 am, davebb123456 wrote:
i can not get my radio in to
adjustment mode, am i doing something wrong, i have a uk
(10) model , i am doing as page 16 of the service manual
says,and the radio just starts up as normal, my civ port
is working and i am using the same jack plug to try and
get the radio in to adjust mode,
Please help,
Thanks Dave 2E0DMB
?
|
Re: i can not get my radio in to adjustment mode
Hi? Yes yes it is ?A 3.5mm mono jack plug ,so only 2 pins to short,? I have used this plug for cat control, with this radio and ham radio deluxe, So I don't know why it will not go into adjustment mode, Thanks Dave
Hi Dave, Hoffy here, just double checking that the 1/8th plug
that you are using has been "shorted" as per the instruction of
the manual.
Cheers and all the best,
Hoffy - VK4OY
On 16/04/2022 5:37 am, davebb123456
wrote:
i can not get my radio in to adjustment mode, am i doing something
wrong, i have a uk (10) model , i am doing as page 16 of the
service manual says,and the radio just starts up as normal, my civ
port is working and i am using the same jack plug to try and get
the radio in to adjust mode,
Please help,
Thanks Dave 2E0DMB
?
|
Re: i can not get my radio in to adjustment mode
Hi Dave, Hoffy here, just double checking that the 1/8th plug
that you are using has been "shorted" as per the instruction of
the manual.
Cheers and all the best,
Hoffy - VK4OY
On 16/04/2022 5:37 am, davebb123456
wrote:
toggle quoted message
Show quoted text
i can not get my radio in to adjustment mode, am i doing something
wrong, i have a uk (10) model , i am doing as page 16 of the
service manual says,and the radio just starts up as normal, my civ
port is working and i am using the same jack plug to try and get
the radio in to adjust mode,
Please help,
Thanks Dave 2E0DMB
?
|
i can not get my radio in to adjustment mode
i can not get my radio in to adjustment mode, am i doing something wrong, i have a uk (10) model , i am doing as page 16 of the service manual says,and the radio just starts up as normal, my civ port is working and i am using the same jack plug to try and get the radio in to adjust mode,
Please help,
Thanks Dave 2E0DMB
?
|
Good day Peter.? You are here!? Hopefully, some of the group can help with your 7000 issue. All the best, Russ KW6T California
On Thursday, April 14, 2022, 03:09:51 AM PDT, Peter <petersava@...> wrote:
Please Can I be considered for membership of the group. As I own an IC7000 that is giving me trouble My Call sign Is? VK6YV Peter Savage 6 Stadia Court Beldon? 6027 Western Australia ? 73s Peter
|
Please Can I be considered for membership of the group. As I own an IC7000 that is giving me trouble My Call sign Is? VK6YV Peter Savage 6 Stadia Court Beldon? 6027 Western Australia ? 73s Peter
|
Re: Claremore OK Hamfest this past weekend.. IC-7000-HDMI Separtation Kit DM5AI Manual
IC-7000-HDMI Separtation Kit DM5AI Manual attached.? I have used it for a year. Jim WI6X
toggle quoted message
Show quoted text
On Apr 11, 2022, at 14:33, Doug Stewart <dstewart@...> wrote:
?
Hi Larry,
Those are in short supply. Neither is available from Icom any longer I do not believe. DM5AL has a separation kit he designed. I am not sure if they are still available or not. You would need to contact him directly.
?
?
It is the SKT7000.
?
Good luck.
73
Doug
N2BEG
?
?
WARNING: External Source Email
I picked up a second IC7000 at the hamfest.. Rig is 9.5 of 10..
It came from an estate, and there was no box, no separation cable- control head mounting. There was a 706markII and it had the separation cable and control head mount, but I wanted the IC7000..all ready have one, nothing new to learn.
Looking for both, let me know in you'd like to part with either or both..
It's the OFC-1579 cable and 2427 Control head base..
Hopefully I won't have to contact ICOM.. unfortunately I have jury duty this week, no phones or calls during business hours..
I can do PAYPAL.. goods and services..
73-
Larry W8LM
Disclaimer The information contained in this communication from the sender is confidential. It is intended solely for use by the recipient and others authorized to receive it. If you are not the recipient, you are hereby notified that any disclosure, copying, distribution or taking action in relation of the contents of this information is strictly prohibited and may be unlawful.
This email has been scanned for viruses and malware, and may have been automatically archived by Mimecast, a leader in email security and cyber resilience. Mimecast integrates email defenses with brand protection, security awareness training, web security, compliance and other essential capabilities. Mimecast helps protect large and small organizations from malicious activity, human error and technology failure; and to lead the movement toward building a more resilient world. To find out more, visit our website.
|
Re: Claremore OK Hamfest this past weekend..
Hi Larry,
Those are in short supply. Neither is available from Icom any longer I do not believe. DM5AL has a separation kit he designed. I am not sure if they are still available or not. You would need to contact him directly.
?
?
It is the SKT7000.
?
Good luck.
73
Doug
N2BEG
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of
Larry Macionski via groups.io
Sent: Sunday, April 10, 2022 1:29 PM
To: [email protected]
Subject: [ic7000] Claremore OK Hamfest this past weekend..
?
WARNING: External Source Email
I picked up a second IC7000 at the hamfest.. Rig is 9.5 of 10..
It came from an estate, and there was no box, no separation cable- control head mounting. There was a 706markII and it had the separation cable and control head mount, but I wanted the IC7000..all ready have one, nothing new to learn.
Looking for both, let me know in you'd like to part with either or both..
It's the OFC-1579 cable and 2427 Control head base..
Hopefully I won't have to contact ICOM.. unfortunately I have jury duty this week, no phones or calls during business hours..
I can do PAYPAL.. goods and services..
73-
Larry W8LM
Disclaimer The information contained in this communication from the sender is confidential. It is intended solely for use by the recipient and others authorized to receive it. If you are not the recipient, you are hereby notified that any disclosure, copying, distribution or taking action in relation of the contents of this information is strictly prohibited and may be unlawful.
This email has been scanned for viruses and malware, and may have been automatically archived by Mimecast, a leader in email security and cyber resilience. Mimecast integrates email defenses with brand protection, security awareness training, web security, compliance and other essential capabilities. Mimecast helps protect large and small organizations from malicious activity, human error and technology failure; and to lead the movement toward building a more resilient world. To find out more, visit our website.
|
Hoffy
WI6X Jim
Doug Stewart