开云体育

All: This is, as someone else mentioned, a very bad idea. The ends of unterminated cables are high impedance node, which means high voltage. For a couple of reasons, the voltage at that point can be

Thanks Steve. Takes care of that. Brian K7ZRZ ---In ic7000@..., <w3ahl@...> wrote: OUT-0 is a control line out of an RRC remote rig control box, not the 7K. Steve, W3AHL ---In

I have had a number of issues with computer programming of rigs, the IC-7000 being one of them. Usually the handshaking problem was related to using the wrong com port, if you are using a USB to

UGH I should wake up first.. If its the 7000 I believe its the second from the right as stated earlier Thank you, Brian Mackey KC1MAC Hams don't let hams get stuck on 2 meter repeaters! :) From: brian

I Stand correct theres only one on the 8000 LOL its the speaker jack but you really have to check and make sure its plugged in tight. Thank you, Brian Mackey KC1MAC Hams don't let hams get stuck on 2

Yeah I never do that I make my edits then send to radio Thank you, Brian Mackey KC1MAC Hams don't let hams get stuck on 2 meter repeaters! :) From: D C _Mac_ Macdonald <k2gkk@...> Reply-To:

Yes :) Thank you, Brian Mackey KC1MAC Hams don't let hams get stuck on 2 meter repeaters! :) From: <cpcohen1945@...> Reply-To: <ic7000@...> Date: Sunday, December 1, 2013 at 10:23 PM

I do. I used the SP-23.

Set the radio baud rate to 19200 using the radio's menus (check the manual). I had no luck with the auto baud setting, but once fixed at 19200, all software works perfectly. -- 73 de Tony

>>> . Incidentally do any of you use external speakers when using the 7000 as a base station. <<< Yes! The IC-7000 loudspeaker is painful to listen to. Use something with a bigger cone (4" - 5") in a

Helen -- You probably know more than I do, so take this FWIW -- . . . Have you done a "reset to factory defaults"? That has cured a multitude of problems, on a multitude of rigs. . Charles VA7CPC PS

Instructions say to send from radio to computer first. After about 2 minutes I get a message that program can't find a baud rate. Does exactly the same thing with 3 V-8000s. * * * * * * * * * * * * 73

OUT-0 is a control line out of an RRC remote rig control box, not the 7K. Steve, W3AHL ---In ic7000@..., <bingoldsby@...> wrote: While looking around the net for something about how to

Great idea they can make it happen ;) Thank you, Brian Mackey KC1MAC Hams don't let hams get stuck on 2 meter repeaters! :) From: D C _Mac_ Macdonald <k2gkk@...> Reply-To:

I have the 8000 as well its really simple. Plug it all together and then send.. Nothing to do on the radio side Thank you, Brian Mackey KC1MAC Hams don't let hams get stuck on 2 meter repeaters! :)

Hopefully the mods will approve this message in a timely manner. Assuming you installed the USB drivers *before* you plugged in the cable the first time, it should work as long as the com port and

I presume you are talking about the RT Systems programmer. I'm having the same problem with my new IC-V8000! I have loaded up all the desired frequencies, tones, etc. but no joy when attempting to

Make sure your in the right plug in the back! Check the manual I think its plug 2 from right to left but again The Manual is the key. Thank you, Brian Mackey KC1MAC Hams don't let hams get stuck on 2

help!! I Have A Icom 7000 And I Cant Seem To Get It To SHAKE hands with my computer. I bought the software and plug from rs systems.need help!!

While looking around the net for something about how to remotely switch the 7000's power on and off, I found this in a forum, from some time back: "if you not use OUT-0 for example you can use it to