Re: SOLD Non working ic-7000
|
Hello Group ,
?I am selling my nonworking IC-7000. It has the dreaded driver board fail. Everything else worked 100%. The head of the radios is 100% and it comes with the separation kit (bracket and cable).
300 plus shipping.
Good on QRZ. email me.
73's
Mike WA3O
|
Re: ic-7000 settings for data modes
@Brian, thanks for the link. I'll follow the instructions and let you know tge results.?
@Mike the link Brian posted should solve both our queries.?
73s
toggle quoted message
Show quoted text
I am using the XGGComms Digimode-4 with the 7000.? I am using the settings recommend in this post -? /g/ic7000/message/40549.
-Brian, KB3ORR
|
Re: Memory bank selection question
Thanks Steve. Appreciate the information. I will try the microphone configuration.
Michael Gardner
K1MLG
toggle quoted message
Show quoted text
On Feb 15, 2024, at 6:47 PM, Steve Murphy <KC4SM@...> wrote:
?I've only ever been able to change banks through the M2, MEM, LST, BNK menu. With the PBT LED off the small knob is M-ch and the outer knob is RIT. I'm not aware of a menu setting that changes the functionality of these controls.
However, if you are using the HM-151 microphone you can configure the F-1 or F-2 soft keys for the BNK function.
73
Steve
KC4SM
Feb 15, 2024 4:59:00 PM Michael Gardner via groups.io <mlgardner96@...>:
I have numerous frequencies in all five memory banks. Using the PBT/M-ch knobs (with PBT disengaged-green light out) I can select channels turning the outer knob but I can no longer select banks with the inner knob which worked previously. I have read through the manual on this subject. I can go into the menu with the frequency/bank list and change banks that way.
I am wondering if I have inadvertently changed a setting somewhere that is causing this problem with not being able to use the knob to select banks.
Thanks for any info,
Michael Gardner
K1MLG
|
Re: Memory bank selection question
I've only ever been able to change banks through the M2, MEM, LST, BNK menu. With the PBT LED off the small knob is M-ch and the outer knob is RIT. I'm not aware of a menu setting that changes the functionality of these controls.
However, if you are using the HM-151 microphone you can configure the F-1 or F-2 soft keys for the BNK function.
73
Steve
KC4SM
Feb 15, 2024 4:59:00 PM Michael Gardner via groups.io <mlgardner96@...>:
toggle quoted message
Show quoted text
I have numerous frequencies in all five memory banks. Using the PBT/M-ch knobs (with PBT disengaged-green light out) I can select channels turning the outer knob but I can no longer select banks with the inner knob which worked previously. I have read through? the manual on this subject. I can go into the menu with the frequency/bank list and change banks that way.
I am wondering if I have inadvertently changed a setting somewhere that is causing this problem with not being able to use the knob to select banks.
Thanks for any info,
Michael Gardner
K1MLG
|
Memory bank selection question
I have numerous frequencies in all five memory banks. Using the PBT/M-ch knobs (with PBT disengaged-green light out) I can select channels turning the outer knob but I can no longer select banks with the inner knob which worked previously. I have read through the manual on this subject. I can go into the menu with the frequency/bank list and change banks that way.
I am wondering if I have inadvertently changed a setting somewhere that is causing this problem with not being able to use the knob to select banks.
Thanks for any info,
Michael Gardner
K1MLG
|
Re: ic-7000 settings for data modes
As I remember (and I could have this backwards) in digital the front mike on the head is muted so that your noise in the shack will not be transmitted, but the other mike jack is not.
The IC-7000 is what I had when I got back into ham radio 5 years ago and it works great on Ft-8.
|
Re: ic-7000 settings for data modes
I am using the XGGComms Digimode-4 with the 7000.? I am using the settings recommend in this post -? /g/ic7000/message/40549. -Brian, KB3ORR
|
Re: ic-7000 settings for data modes
Coincidently I am trying to use Signalink with my IC-7000 today.? You are right...slimpickin' on info via YT.? Will be following.
On Tue, Feb 13, 2024 at 10:33 AM, m0cvz - Don <m0cvz@...> wrote: I want to operate WSJTx with my 7000.
I've connected the radio to my laptop, via a rigblaster advantage and am using Ham Radio Deluxe for rig.? control.?
FT8 is decoding fine. Just wondered if there are any settings on the actual radio that I need to configure,? to ensure a good receive and transmit signal. Info on this is sparse on the Internet??
Apologies if this topic has already been covered.?
|
Re: CAT control of 9600/1200 bps data port
> Note binary for "0" and "1" data values.
The x00/x01 in decimal happen to be equivalent to their Hex representations in decimal, but all the values listed in these commands are in hex and are sent as 2 characters 00-FF. That's what the "x" is indicating.
It's a small distinction but hex and binary are not the same.
73
Danny, K5CG
HH 550-000-0609
SKCC 14257
From: "John Spoonhower" <jpspoonhower@...> To: "ic7000" < [email protected]> Sent: Wednesday, February 14, 2024 8:43:41 AM Subject: Re: [ic7000] CAT control of 9600/1200 bps data port
Many thanks to those who offered suggestions. It turns out that the table on page 146 is indeed incorrect.
The listed command "0A" is in fact a sub-command of "1A". The proper commands for executing the change of bps are:
"xFE xFE x70 xE0 x1A x0A x00 xFD" for 1200 bps
"xFE xFE x70 xE0 x1A x0A x01 xFD" for 9600 bps
Note binary for "0" and "1" data values.
I presume the other entries 06-09 listed as commands may also be sub-commands as well, but I have not tested these. Beware!
73, John, NX2I
|
Re: CAT control of 9600/1200 bps data port
Many thanks to those who offered suggestions. It turns out that the table on page 146 is indeed incorrect.
The listed command "0A" is in fact a sub-command of "1A". The proper commands for executing the change of bps are:
"xFE xFE x70 xE0 x1A x0A x00 xFD" for 1200 bps
"xFE xFE x70 xE0 x1A x0A x01 xFD" for 9600 bps
Note binary for "0" and "1" data values.
I presume the other entries 06-09 listed as commands may also be sub-commands as well, but I have not tested these. Beware!
73, John, NX2I
|
ic-7000 settings for data modes
I want to operate WSJTx with my 7000.
I've connected the radio to my laptop, via a rigblaster advantage and am using Ham Radio Deluxe for rig.? control.?
FT8 is decoding fine. Just wondered if there are any settings on the actual radio that I need to configure,? to ensure a good receive and transmit signal. Info on this is sparse on the Internet??
Apologies if this topic has already been covered.?
|
Re: CAT control of 9600/1200 bps data port
John -
? ?I've never directly programmed my IC-7000, nor have I ever used the packet data interface - so feel free to ignore this if you get more knowledgable feedback! ?;-)
? ?That said, some observations:
? ?- I compared my hardcopy version of the IC-7000 manual (the one that originally came with my radio) and my Section 17, page 146 visually matches the downloaded copy you have.? However, the Command Table entries for (what looks like...) Commands 0x06 - 0x0A on pg 146 look strange. Namely:
? ?1) the entries are "out of order". For the rest of the Command Table (which begins on page 142) the entries are all in numerical order, indexed first by Command # and then Subcommand #. But on page 146 the table jumps from Command 0x1A, Subcommand 0x050119 to "Commands" 0x06 - 0x0A (all with no Subcommands?), and then jumps back to Command 0x1B, Subcommand 0x00. Curious...
? ?2) Commands 0x06 - 0x0A have already been assigned to other functions?back on page 142 of the table, where they are shown in the proper numerical order! In other words, the out-of-order entries on page 146 (including the 0x0A one you're using) is in conflict with the assignments already made on page 142. At the very least, it looks like we have some kind of misprint in the documentation.
? ?If that's the case (i.e. the documentation is wrong) - what is the right answer? At this point I'm merely speculating, but it might be worth a try... ?What If: the 0x06 - 0x0A "Commands" on page 146 were mistakenly put in the wrong column, and they really should be Subcommands? Since something has to go in the Commands column - What If: they're all just additions to the "0x1A" Command family? This is just a guess, but moving 0x06 - 0x0A over to the Subcommand column and replacing them with 0x1A Commands would "fix" the numerical order?anomaly and remove the assignment clash with the original (page 142) Commands 0x06 - 0x0A. Sounds promising to me... ?;-)
? ?Again, this is just "paper debugging" (and a lot of speculation), so if you receive any better informed ideas feel free to ignore this. But if not, it sounds like you're set up to easily test the hypothesis if you want to try. Let us know what you find!
? ?73's and Good Luck,
? ?- Richard, ?NC6RJ
|
Re: CAT control of 9600/1200 bps data port
To me the manual is unclear as to what the actual byte code
should be for a "(0=off, 1=ON)" statement.
The manual states that the "Data Area is BCD code data for
frequency or memory number entry"
the unwritten and unstated assumption therefore is that everything
else is a full Ascii character.
so is "0" a binary or a character encoding?
You might try "x30" and "x31" in case it is supposed to be the
Ascii character "0" (zero) or "1" (one).
as opposed to the binary value of "0" (x00) or "1" (x01)
/s/ BillTurner, wb4alm
On 2/12/24 14:29, John Spoonhower
wrote:
toggle quoted message
Show quoted text
Greg, and others,
I have attached the relevant manual page from the IC-7000 manual;
I just downloaded it from the Icom web site.
The command code I see for setting / getting the bps setting is
shown as "0A". Has this changed ?
I have successfully run a a number of similar commands listed in
the command table from this version of the manual.
For example:
xFE xFE x70 xE0 x03 xFD returns the operating frequency (144390.00
Mhz) as:
FE FE 70 E0 03 FD FE FE E0 70 03 00 00 39 44 01 FD.
What am I doing wrong?
John NX2I
|
Re: CAT control of 9600/1200 bps data port
Greg, and others,
I have attached the relevant manual page from the IC-7000 manual; I just downloaded it from the Icom web site.
The command code I see for setting / getting the bps setting is shown as "0A". Has this changed ?
I have successfully run a a number of similar commands listed in the command table from this version of the manual.
For example:
xFE xFE x70 xE0 x03 xFD returns the operating frequency (144390.00 Mhz) as:
FE FE 70 E0 03 FD FE FE E0 70 03 00 00 39 44 01 FD.
What am I doing wrong?
John NX2I
|
Re: CAT control of 9600/1200 bps data port
Pretty sure you have your codes confused, From my 7000 manual: ? 0A Memory to VFO 00 Frequency data 01 Mode data And the end needs to be FD for end of data not FE ? And in the command listing I do not see anything for controlling the data connection speed. ? I might be wrong though… ? Greg NZ6E ?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of John Spoonhower Sent: Monday, February 12, 2024 9:54 AM To: [email protected]Subject: [ic7000] CAT control of 9600/1200 bps data port ? I am interested in trying to control the 9600/1200 bps setting for the data connection to the IC-7000. Thus far I have tried and failed using the "send Command" option in FLRIG.
Has anyone succeeded in doing this?
According to the manual command reference this is done with command 0A so, I have tried the commands:
xFE xFE x70 xE0 x0A x00 FD (for 1200 bps) and,
xFE xFE x70 xE0 x0A x01 FD (for 9600 bps) .
These are claimed to turn on / off the 9600 bps connection.
Are there other approaches I should consider?
73, John, NX2I
|
Re: CAT control of 9600/1200 bps data port
yes I want to toggle? the audio connection setting from 9600/1200 bps. How do I do this using a remote controller? NX2I
On Mon, Feb 12, 2024 at 1:09?PM John Spoonhower via <jpspoonhower= [email protected]> wrote: Dave, ypur answer is not clear for me. I want to change the bps setting for packet. I am using the din 6 connector on the rear of the IC-7000. Nx2i
Hi the 1200/9600 is the audio data port not cat data, Dave 2E0DMB?
I am interested in trying to control the 9600/1200 bps setting for the data connection to the IC-7000. Thus far I have tried and failed using the "send Command" option in FLRIG.
Has anyone succeeded in doing this?
According to the manual command reference this is done with command 0A so, I have tried the commands:
xFE xFE x70 xE0 x0A x00 FD (for 1200 bps) and,
xFE xFE x70 xE0 x0A x01 FD (for 9600 bps) .
These are claimed to turn on / off the 9600 bps connection.
Are there other approaches I should consider?
73, John, NX2I
|
Re: CAT control of 9600/1200 bps data port
Dave, ypur answer is not clear for me. I want to change the bps setting for packet. I am using the din 6 connector on the rear of the IC-7000. Nx2i
Hi the 1200/9600 is the audio data port not cat data, Dave 2E0DMB?
I am interested in trying to control the 9600/1200 bps setting for the data connection to the IC-7000. Thus far I have tried and failed using the "send Command" option in FLRIG.
Has anyone succeeded in doing this?
According to the manual command reference this is done with command 0A so, I have tried the commands:
xFE xFE x70 xE0 x0A x00 FD (for 1200 bps) and,
xFE xFE x70 xE0 x0A x01 FD (for 9600 bps) .
These are claimed to turn on / off the 9600 bps connection.
Are there other approaches I should consider?
73, John, NX2I
|
Re: CAT control of 9600/1200 bps data port
Hi the 1200/9600 is the audio data port not cat data, Dave 2E0DMB?
I am interested in trying to control the 9600/1200 bps setting for the data connection to the IC-7000. Thus far I have tried and failed using the "send Command" option in FLRIG.
Has anyone succeeded in doing this?
According to the manual command reference this is done with command 0A so, I have tried the commands:
xFE xFE x70 xE0 x0A x00 FD (for 1200 bps) and,
xFE xFE x70 xE0 x0A x01 FD (for 9600 bps) .
These are claimed to turn on / off the 9600 bps connection.
Are there other approaches I should consider?
73, John, NX2I
|
CAT control of 9600/1200 bps data port
I am interested in trying to control the 9600/1200 bps setting for the data connection to the IC-7000. Thus far I have tried and failed using the "send Command" option in FLRIG.
Has anyone succeeded in doing this?
According to the manual command reference this is done with command 0A so, I have tried the commands:
xFE xFE x70 xE0 x0A x00 FD (for 1200 bps) and,
xFE xFE x70 xE0 x0A x01 FD (for 9600 bps) .
These are claimed to turn on / off the 9600 bps connection.
Are there other approaches I should consider?
73, John, NX2I
|
m0cvz - Don
Michael Gardner
Danny K5CG