开云体育

of Jo, I don't think you'd want one even if you could find one. That BNC spike will break right off. I think Bonnie is talking about an ATX she got that had the 3/8-24 *instead* of a BNC or

INRAD is Internationl Radio, tha supplies IF filters for transceivers. The web address is: http://www.qth.com/inrad/index.htm 73, Skip Davis NC9O ===== Skip Davis,

The Palm minipaddle is VERY nice. I saw it at Dayton. SMOOTH! But I'm not about to spend $70 on a paddle that's going to get stuffed in a bag along with a radio, ATX, small gel-cell, headphones,

fit to go in my FT-817. Julian, Yours is like all of the FT817s. I would guess that it was done to help hold the batteries in the carrier. I also have to remove the batteries to get the carrier out,

Hello, I have been reading references to an INRAD filter. I am not familiar with the term. Is this a brand name? or a type? If it is a brand name where can I find it? -- Best regards, Robert

Barry, I've been trying to follow all the cell messages, I apologise if this has been covered. Last night there was the Mother and Father of all thunder storms, as a result I was without electricity

I will measure my cells but they are not tight at all. Easily slide under case edge. Mine are off the shelf cells made for general consumer use. -- Richard Clemens clemens@...

My battery tray has a plastic flap that protects the cells from the edge of the case. This may be a new addition, as the unit is not yet a week old. I too had a problem in putting in the tray will

The ones I got from Maplin Electronics are, as near as I can measure them with just a ruler, 15.0mm in diameter. The fit in the 817 is so tight that extra half a millimeter will make a big

dry cell <SNIP> not quite than normal Julian, The AA batteries come in several standard sizes and a few non- standard. Users beware. Not all fit in the 817. Diameters of some are 16.5 mm rather

It never occurred to me to do that. In fact, I had initially covered the cells with electrical tape to provide some extra insulation, before putting the whole lot in, but this just added to the

There are a couple...RATS and FT Basic. For memory management there's also ARDTS. I've purchased ARDTS and FTBASIC and the latter does it all, including memory management. It's a bargain. If you

15 to hr. Hi Tom, You have the choice of 6, 8 and 10 hours. You can do 14 (6+8) or 16 (8+8), but to do 15, yo will have to watch and turn off the charger with an hour left to go. Likely 14 will

For quickloading NICD and NIMH batteries in the FT-817, i glued a small walkmen loading socket (3,5x1,3mm)just under the SP-PH switch. This socket is accessed by an additionally drilled 4mm hole in

FT-817 is a fine cw rig. I also recommend the Inrad 300hz cw filter. Using a Bencher paddle at home and a Palm mini-paddle portable. One nice thing about the Palm is that the magnetic base

Ok I understand now your not using the BNC version. I guess the PL-259 connector is stronger and can handle the sideward pressure. Thanks for the reply, 73's Julio

So many people seem to have done the green wire mod and used the dry cell carrier to hold NiMH cells and not mentioned any problems that I was surprised to end up abandoning the attempt. The carrier,

You must fill battery tray while it is in the radio. I switch to external power at this point or run lower power to entend my time That is the way my tray arrived and I assume that is the norm.

I found the MFJ version to be a little nicer, (physically) than the Bencher. Almost identical but a significant less in money.

keyer CW You can adjust the delay time between Tx and Rx with the CW DELAY option. I have mine set at 100 mSec. After this adjustment, the delay seems satisfactory to me. I use the built-in