Re: Hammer C-31 Planer Issue - Motor Triping
Great to hear you are sorted, Annu
toggle quoted message
Show quoted text
[Edited Message Follows] Hey All,
My hammer is now working.
Brian,
Thanks for your advice about bolting down the motor and seeing if it straightens out, that did the trick. ?BTW, your parallel arms my be my favorite accessory.
Imran/Roger,
Thanks for all your advice and troubleshoot tips on the electrical system.
-Annu
|
Re: Remote Start Switch suddenly stopped working on K700s
the battery is under the cover on the end of the slider, underneath.??
On Sunday, January 17, 2021, 07:40:29 AM PST, Jerry P <jerry-pac-man@...> wrote:
|
Re: Remote Start Switch suddenly stopped working on K700s
|
Re: Remote Start Switch suddenly stopped working on K700s
i am speaking of the switch on the slider ...any hints to where the battery is??
|
|
|
Re: Remote Start Switch suddenly stopped working on K700s
If you are speaking of switch on slider it’s most likely time to replace battery. Can’t help you more as I do not have it.
Imran
toggle quoted message
Show quoted text
On Jan 17, 2021, at 9:31 AM, G. Lane <lane247@...> wrote: ?The remote start switch for the saw suddenly stopped working on the k700S making panels hard to cut because i can hardly reach? the start switch on the side that does work.? Any advice as to where to begin troubleshooting or things i should try?? I removed cover plate and discovered it appears to be wireless?? Anyway? any help would be greatly appreciated. Its is a 2012 machine that has been trouble free up till now.? Thanks
|
Re: Hammer C-31 Planer Issue - Motor Triping
Hey All,
My hammer is now working.
Brian,
Thanks for your advice about bolting down the motor and seeing if it straightens out, that did the trick. ?BTW, your parallel arms my be my favorite accessory.
Imran/Roger,
Thanks for all your advice and troubleshoot tips on the electrical system.
-Annu
|
Remote Start Switch suddenly stopped working on K700s
The remote start switch for the saw suddenly stopped working on the k700S making panels hard to cut because i can hardly reach? the start switch on the side that does work.? Any advice as to where to begin troubleshooting or things i should try?? I removed cover plate and discovered it appears to be wireless?? Anyway? any help would be greatly appreciated. Its is a 2012 machine that has been trouble free up till now.? Thanks
|
In long narrow spaces they give you flexibility with the smaller sliding tables
I have had to fight the planning authority for every inch on my new workshop, so it would be nice to site the machine permanently rather than moving it around on the rolling carriage.
But it all hinges on the centre of rotation is key.
Sent from my Windows Phone
Cliff,
turntable is not on the saw, rather saw is on the turn table
Imran
On Jan 16, 2021, at 11:19 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:
?
I gotta ask.?? What? does one do with a turn table on a sliding saw? or any table saw?
On 1/16/21 3:22 PM, Paul Curme wrote:
toggle quoted message
Show quoted text
Does anyone have a copy of the drawing of the top mounting plate for the almost mythical turntable for the BF6.
I remember mounting a 6-41 M on one for an exhibition in 1994 while working for the guys that were the uk sales agent back then but cant figure out the centre point of rotation for my machine as its not as straight forward as one might expect. Because we got
it wrong at the 1st attempt.
I've located a potential bearing that is the right size and load capacity. But need the top plate layout, because the layout is to close to guess.
Catalog picture without the machine would do at a pinch.
Thanks in advance.
Sent from my Windows Phone
|
Re: Hammer C-31 Planer Issue - Motor Triping
I feel your frustration, Annu. I’m glad, though, that you confirmed the motor short as that eliminates any remaining doubt in that area and looks as if I was wrong in insisting that the brake module was at fault.
toggle quoted message
Show quoted text
On 17 Jan 2021, at 01:37, Brian Lamb < blamb11@...> wrote:
They are part of the outer motor housing extrusion. I would check with Felder and if they are ok with it, clamp it to a solid flat surface before you install it and see if you can pull the flanges back flat without breaking anything. If it works, then it’s up to you if you want to finish installing it, if they crack, Felder will have to get you another motor, and who knows how long that will take.
Hey All,
I was wrong about the key. ?On closer inspection, it was not welded and just needed to be tapped in. ?Not sure if I should attempt with the Bent rails though.
-Annu
|
Cliff,
turntable is not on the saw, rather saw is on the turn table
Imran
toggle quoted message
Show quoted text
On Jan 16, 2021, at 11:19 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote: ?
I gotta ask.?? What? does one do with a turn table on a sliding
saw? or any table saw?
On 1/16/21 3:22 PM, Paul Curme wrote:
Does
anyone have a copy of the drawing of the top mounting plate
for the almost mythical turntable for the BF6.
I remember mounting a 6-41 M on one for an exhibition in 1994
while working for the guys that were the uk sales agent back
then but cant figure out the centre point of rotation for my
machine as its not as straight forward as one might expect.
Because we got it wrong at the 1st attempt.
I've located a potential bearing that is the right size and
load capacity. But need the top plate layout, because the
layout is to close to guess.
Catalog picture without the machine would do at a pinch.
Thanks in advance.
Sent from my Windows Phone
|
I don't use a spindle sander much but have an old State T150 which was the earlier version of the T5.. Both had a tilting spindle and sleeves from 1/4-4".? The best spindle sanders made in the US were from Kindt Collins.? Dave
toggle quoted message
Show quoted text
This is the spindle sander I have - not the most refined piece of gear, and not for heavy production, but it works well and costs less than the aluminum sanding heads for the shaper:
David Best
https://www.instagram.com/davidpbest/
If you’re talking about these sanding heads, I think you’ll be disappointed. ? They rotate entirely too fast and do not oscillate. ? A bobbin sander is a much better alternative.
<screenshot_4651.jpeg>
On Jan 16, 2021, at 5:44 PM, Dmitry Ivanovs via < divanov2@...> wrote:
Overkill !! Why not just buy head for shaper from felder different diameters. That’s what I’m using if need it?
Elegance Custom Cabinetry?
Minneapolis, Minnesota?
Regards?
Dmitry Ivanovs .
?I know I am reviving an old thread, but...
I was looking at the Laguna and Delta newer floor standers as they have a trunnion tiliting mechanism so the table stays flat.? Thoughts?
<Screenshot 2021-01-16 140249.png><Screenshot 2021-01-16 140708.png>
Thoughts?
PK
|
I gotta ask.?? What? does one do with a turn table on a sliding
saw? or any table saw?
On 1/16/21 3:22 PM, Paul Curme wrote:
toggle quoted message
Show quoted text
Does
anyone have a copy of the drawing of the top mounting plate
for the almost mythical turntable for the BF6.
I remember mounting a 6-41 M on one for an exhibition in 1994
while working for the guys that were the uk sales agent back
then but cant figure out the centre point of rotation for my
machine as its not as straight forward as one might expect.
Because we got it wrong at the 1st attempt.
I've located a potential bearing that is the right size and
load capacity. But need the top plate layout, because the
layout is to close to guess.
Catalog picture without the machine would do at a pinch.
Thanks in advance.
Sent from my Windows Phone
|
Dmitry, I haven't seen the Jr. in action, but larger versions yes. The primary benefit is speed of throughput.? You have to press a lot of veneer to justify that. Our 5x10' vacuum press is in use more often than not, and I wouldn't consider it. I do outsource some components to Saunders Veneer Specialties in Wisconsin precisely because of them being hot pressed however.
There's a used one on Woodweb for $12k Jason Holtz
J. Holtz Furniture
3307 Snelling Ave. South Minneapolis, MN 55406
612 432-2765 -- Jason J. Holtz Furniture 3307 Snelling Ave. South Minneapolis, MN 55406
|
This is the spindle sander I have - not the most refined piece of gear, and not for heavy production, but it works well and costs less than the aluminum sanding heads for the shaper:
David Best
https://www.instagram.com/davidpbest/
toggle quoted message
Show quoted text
If you’re talking about these sanding heads, I think you’ll be disappointed. ? They rotate entirely too fast and do not oscillate. ? A bobbin sander is a much better alternative.
<screenshot_4651.jpeg>
On Jan 16, 2021, at 5:44 PM, Dmitry Ivanovs via < divanov2@...> wrote:
Overkill !! Why not just buy head for shaper from felder different diameters. That’s what I’m using if need it? Elegance Custom Cabinetry? Minneapolis, Minnesota?
Regards?
Dmitry Ivanovs . ?I know I am reviving an old thread, but...
I was looking at the Laguna and Delta newer floor standers as they have a trunnion tiliting mechanism so the table stays flat.? Thoughts?
<Screenshot 2021-01-16 140249.png><Screenshot 2021-01-16 140708.png>
Thoughts?
PK
|
If you’re talking about these sanding heads, I think you’ll be disappointed. ? They rotate entirely too fast and do not oscillate. ? A bobbin sander is a much better alternative.
David Best
https://www.instagram.com/davidpbest/
toggle quoted message
Show quoted text
On Jan 16, 2021, at 5:44 PM, Dmitry Ivanovs via < divanov2@...> wrote:
Overkill !! Why not just buy head for shaper from felder different diameters. That’s what I’m using if need it? Elegance Custom Cabinetry? Minneapolis, Minnesota?
Regards?
Dmitry Ivanovs . ?I know I am reviving an old thread, but...
I was looking at the Laguna and Delta newer floor standers as they have a trunnion tiliting mechanism so the table stays flat.? Thoughts?
<Screenshot 2021-01-16 140249.png><Screenshot 2021-01-16 140708.png>
Thoughts?
PK
|
I would imagine it has enough ommph , they have been selling the junior for a long time.
2 things it looks low, you will be bending down when you put your panel in. The one I used we had the (well one of them) glueup/layup table in front of it and the platten was a bit higher, I can’t remember how much but we had to lift the panels to get them in. Our substrate was 1” or 1.25” mdf - wouldn’t want to bend down loading one of those. ?We also had to put in spacers to fill in the dead space, not sure if it was because ours was so big (5’ x 10’ i think) but not really a big deal - just some squares of the same thickness in the corners and here and there depending on the unfilled space. But the awesome thing is you don’t need plattens for the panel you are glueing up and it is fast because of the heat.?
toggle quoted message
Show quoted text
On Jan 16, 2021, at 9:57 PM, Dmitry Ivanovs via groups.io <divanov2@...> wrote:
? I do have vacuum bag but I’m really wanna understand statistic psi vs vacuum bag and hot press. It’s Joos junior is give away enough psi Elegance Custom Cabinetry Minneapolis, Minnesota Regards Dmitry Ivanovs .On Jan 16, 2021, at 20:46, imranindiana via groups.io <imranindiana@...> wrote:
?I am not familiar with this but it will not do curved (vertically) work like a vacuum bag. Maybe, that is not important to you.
Imran
On Jan 16, 2021, at 9:32 PM, Dmitry Ivanovs via groups.io <divanov2@...> wrote:
?Hi guys ,
Anybody seen that press in action ?
U think it’s enough pressure for veneer and preduce better quality pressure vs vacuum bag ?
Elegance Custom Cabinetry
Minneapolis, Minnesota
Regards
Dmitry Ivanovs .
<image0.jpeg>
<image1.jpeg>
|
I do have vacuum bag but I’m really wanna understand statistic psi vs vacuum bag and hot press. It’s Joos junior is give away enough psi
Elegance Custom Cabinetry
Minneapolis, Minnesota
Regards
Dmitry Ivanovs .
toggle quoted message
Show quoted text
On Jan 16, 2021, at 20:46, imranindiana via groups.io <imranindiana@...> wrote:
?I am not familiar with this but it will not do curved (vertically) work like a vacuum bag. Maybe, that is not important to you.
Imran
On Jan 16, 2021, at 9:32 PM, Dmitry Ivanovs via groups.io <divanov2@...> wrote:
?Hi guys ,
Anybody seen that press in action ?
U think it’s enough pressure for veneer and preduce better quality pressure vs vacuum bag ?
Elegance Custom Cabinetry
Minneapolis, Minnesota
Regards
Dmitry Ivanovs .
<image0.jpeg>
<image1.jpeg>
|
I am not familiar with this but it will not do curved (vertically) work like a vacuum bag. Maybe, that is not important to you.
Imran
toggle quoted message
Show quoted text
On Jan 16, 2021, at 9:32 PM, Dmitry Ivanovs via groups.io <divanov2@...> wrote:
?Hi guys ,
Anybody seen that press in action ?
U think it’s enough pressure for veneer and preduce better quality pressure vs vacuum bag ?
Elegance Custom Cabinetry
Minneapolis, Minnesota
Regards
Dmitry Ivanovs .
<image0.jpeg>
<image1.jpeg>
|
More than likely yes, I used to work in the veneer room of a very high end custom corporate furniture company and we had a much larger version, the heat will have you pressed up and ready to go in no time.
toggle quoted message
Show quoted text
On Jan 16, 2021, at 9:32 PM, Dmitry Ivanovs via groups.io <divanov2@...> wrote:
? Hi guys ,Anybody seen that press in action ?U think it’s enough pressure for veneer and preduce better quality pressure vs vacuum bag ?Elegance Custom Cabinetry Minneapolis, Minnesota Regards Dmitry Ivanovs . 
|
imran
Jason Holtz
David P. Best