Re: P coupling Felder adapter to Hammer

开云体育

I have been selling for years now, parallel fences to fit the Hammer and Minimax machines that bolt to the t-slot in the side of the slider. I do limit the width to roughly 25”-26” of support and no issues that I have ever heard of. I would not hang the Felder 1M extension on any sort of adapter on the Hammer slot arrangement, that would be asking for trouble.

Brian Lamb
blamb11@...
www.lambtoolworks.com

Show quoted text

On Jun 27, 2023, at 10:50 PM, bram.baert@... wrote:

Hi Nathan,

Over a year ago I was also playing with that idea and whipped up a quick prototype as can be seen in the picture below. It is/was the goal to make some 3d printed parts and use the VEIKO T ruler () To date, I didn't spent the time to get the design forward. Currently I am just using a stop block that I fix with an F-clamp. I fixed it on the top T-slot as I have my doubts about the strength of the side mounted T-slot when it comes to being loaded with a 60-70 cm plywood panel. Does anybody have experience with load capabilities of the side of the sliding table on a Hammer?

<20230628_073452.jpg>

Regards
Bram

Re: AD941 dust hose attachment

#131109

开云体育

Hi Bill Belanger,

So the larger end of your 120mm adapter will fit over the plastic housing on the machine, but do you know if it’s a snug fit? ?Does the 120mm end have any taper to it? ?I’m wanting that connection to be just about semi permanent. Only because of the flipping action of the hose back and fourth to change operations. ?Maybe I can use a pop-rivet gun to secure it, unless it’s soft enough to use a hose clamp to really hold it in there well. ?

Thx,

Wade

Show quoted text

On Jun 28, 2023, at 8:25 AM, Bill Belanger <bllblngr@...> wrote:

?Wade, I sell adapters?

Bill Belanger?

On Jun 28, 2023, at 08:22, rodsheridan <riderofgallifrey@...> wrote:

?I used 5” hose, which works with the Felder right angle connector?

Regards, Rod

Re: AD941 dust hose attachment

#131108

开云体育

Hi Brett Wissel,

That could be a viable option, Thank You for the heads up.

Wade

Show quoted text

On Jun 28, 2023, at 8:25 AM, Brett Wissel <Brettwissel@...> wrote:

?
I used a Fernco rubber fitting adaptor?from?a?local plumbing supply house, But can't tell you which one at the moment. It fits over the metal ring on the small side and tapers larger to also fit outside?a 6" spiral flex hose.

Prior to that, I used a similar but different Fernco to adapt to a similar size 4" spiral?flex hose.

It's easy to forget that close enough is good enough because the rubber can/will stretch. But the table specs should help a lot.

On Wed, Jun 28, 2023 at 9:26?AM Wade Dees <wjdsignature@...> wrote:
Hello FOG,

To all you AD941 owners.? The machine dust hose attachment has an outside diameter of 120mm or 4.72”.? The hose I use in my shop has an inside diameter of 110mm or 4.33”.? What did you use to adapt the hose to your machine.?
The Felder adapter will not work for my situation.

Thx,

Wade

--
Brett Wissel
Saint Louis Restoration
1831 S Kingshighway Blvd (at Shaw Blvd)
St Louis, MO 63110

314.772.2167
brett@...

Re: AD941 dust hose attachment

#131107

开云体育

Hi Bob Wise,

I’m just connecting flex ducting that has the reinforced spiral wire that coils through it. Wanting to make a direct attachment. ?

Some have mentioned they use Felder’s right angle adapter, but I don’t see the need on my situation to use a right angle adapter. ?Just a straight tapered adapter would suffice. ?

Thx,

Wade

Show quoted text

On Jun 28, 2023, at 8:36 AM, Bob Wise <bob@...> wrote:

?
What material are you using?

On Wed, Jun 28, 2023 at 8:35?AM Chris Reyerson <reyerson@...> wrote:
I use my 3D printer to grow a adapter between the machine port and the hose I use.? A 3D printer has all kinds of uses in a wood shop for things like this.

Chris?

Re: AD941 dust hose attachment

#131106

What material are you using?

Show quoted text

On Wed, Jun 28, 2023 at 8:35?AM Chris Reyerson <reyerson@...> wrote:

I use my 3D printer to grow a adapter between the machine port and the hose I use.? A 3D printer has all kinds of uses in a wood shop for things like this.

Chris?

Re: AD941 dust hose attachment

#131105

I use my 3D printer to grow a adapter between the machine port and the hose I use.? A 3D printer has all kinds of uses in a wood shop for things like this.

Chris?

Re: AD941 dust hose attachment

#131104

开云体育

Wade, I sell adapters?

Bill Belanger?

Re: AD941 dust hose attachment

#131103

I used a Fernco rubber fitting adaptor?from?a?local plumbing supply house, But can't tell you which one at the moment. It fits over the metal ring on the small side and tapers larger to also fit outside?a 6" spiral flex hose.

Prior to that, I used a similar but different Fernco to adapt to a similar size 4" spiral?flex hose.

It's easy to forget that close enough is good enough because the rubber can/will stretch. But the table specs should help a lot.

Show quoted text

On Wed, Jun 28, 2023 at 9:26?AM Wade Dees <wjdsignature@...> wrote:

Hello FOG,

To all you AD941 owners.? The machine dust hose attachment has an outside diameter of 120mm or 4.72”.? The hose I use in my shop has an inside diameter of 110mm or 4.33”.? What did you use to adapt the hose to your machine.?
The Felder adapter will not work for my situation.

Thx,

Wade

--

Brett Wissel
Saint Louis Restoration
1831 S Kingshighway Blvd (at Shaw Blvd)
St Louis, MO 63110

314.772.2167
brett@...

Re: AD941 dust hose attachment

#131102

I used 5” hose, which works with the Felder right angle connector?

Regards, Rod

AD941 dust hose attachment

#131101

Hello FOG,

To all you AD941 owners.  The machine dust hose attachment has an outside diameter of 120mm or 4.72”.  The hose I use in my shop has an inside diameter of 110mm or 4.33”.  What did you use to adapt the hose to your machine.  
The Felder adapter will not work for my situation.

Thx,

Wade

Re: Job hiring #poll-notice

#131100

Looks like spam/scam.? Should be moderated or blocked?

Re: Shortening a bandsaw blade

Mike D.

#131099

Update:

Starrett Customer Service came through on this… the official line is that they don’t repair blades, but given the cost of the blade and that it’s a one-off ‘mulligan’,?they’ll have me ship?it back to the factory, to a specific person. My guess is somebody called in a favor.

Loud shoutout to Starrett.

Mike D.

Show quoted text

On Wednesday, June 28, 2023, 06:37, Mike D. via groups.io <mjcdorsam@...> wrote:

Recently, I purchased a carbide-tipped bandsaw blade from Starrett, but?mis-read the description - leading to a 13’ 4” blade for my 13’ N4400. A rather expensive senior-moment without reading glasses.

Starrett won’t exchange the blade, and the current sense is they no longer provide repair services - Customer Service is looking into this.

Any help is appreciated.
Thanks.
Mike D.

--
Mike D.
Annapolis, MD
AD951; K700S; N4400

--
Mike D.
Annapolis, MD
AD951; K700S; N4400

Re: Troubleshooting Problems with Felder Machines

#131098

It could be more generic, however it’s a good place to start.

You would be amazed the number of customers who haven’t read the manual and their problems are as follows

- emergency stop button depressed

- cover, hood or door interlock switch issue because they’re trying to start a machine with an interlock active

- no power applied to the machine due to an installation error

As I always say during training courses, “ read the manual”

Many users don’t have the troubleshooting skills that many FOG members have.

Regards, Rod

Re: rip blade

#131097

Felder obviously, you need to supply address, name and phone number.

I often buy FS Tools blades, made in North America.

Regards, Rod

Job hiring #poll-notice

Group Notification

#131096

ROCHE COMPANY HIRING

Data operator is needed as a member of staff to be employed to enter or update data on a computer/laptop or on your phone, %100 strictly online work from home job and its flexible hours of work pay of $30/hr, payment is weekly or bi-weekly.. Send an email if interested to.

?

rochehirenicho (at) gmail.com

Thank you for voting.

Results

See Who Responded

Re: rip blade

#131095

Another vote here for Ridge Carbide.? I recently bought two blades from them, good service, no issues.? They emailed me just to confirm that I really wanted Felder 30mm arbor with pin holes, and shipped the blades out within a few days.?

?

I also got a Forrest dado king from Sliver’s Mill.? Again, decent service, no issues, shipped fairly quickly.?

?

Each purchase was through their web pages, but each site lists a phone number, & presumably you could call in an order.? I called Ridge with some questions before purchase, they were very helpful.

I agree, the internet is the wild west, no telling where your info ends up. . .

Shortening a bandsaw blade

Mike D.

#131094

Recently, I purchased a carbide-tipped bandsaw blade from Starrett, but?mis-read the description - leading to a 13’ 4” blade for my 13’ N4400. A rather expensive senior-moment without reading glasses.

Starrett won’t exchange the blade, and the current sense is they no longer provide repair services - Customer Service is looking into this.

Any help is appreciated.

Thanks.

Mike D.

--
Mike D.
Annapolis, MD
AD951; K700S; N4400

Re: P coupling Felder adapter to Hammer

#131093

Hi Nathan,

Over a year ago I was also playing with that idea and whipped up a quick prototype as can be seen in the picture below. It is/was the goal to make some 3d printed parts and use the VEIKO T ruler () To date, I didn't spent the time to get the design forward. Currently I am just using a stop block that I fix with an F-clamp. I fixed it on the top T-slot as I have my doubts about the strength of the side mounted T-slot when it comes to being loaded with a 60-70 cm plywood panel. Does anybody have experience with load capabilities of the side of the sliding table on a Hammer?

Regards
Bram