Re: Felder K700S (and others) Wenge Zero Clearance Inserts
|
Re: Felder K700S (and others) Wenge Zero Clearance Inserts
I'd like two as well 174 NW?Thompson Rd, Poulsbo, WA 98370
On Sat, Mar 12, 2022 at 10:10 PM Robert Johnson < woodewe@...> wrote: Hi,
I would like to order one (two if possible?).
My address is:
159 Denneboom Road
Coupeville, WA 98239
phone is 360-678-6480
Thanks, Bob Johnson
|
Re: Felder K700S (and others) Wenge Zero Clearance Inserts
Hi,
I would like to order one (two if possible?).
My address is:
159 Denneboom Road
Coupeville, WA 98239
phone is 360-678-6480
Thanks, Bob Johnson
|
Re: Felder parallel fence
You could probably get the full 24”-26” with mine, they stick out a lot less than the Felder unit.
toggle quoted message
Show quoted text
On Mar 12, 2022, at 7:23 PM, Dan Gavrilyuk < dgwoodco@...> wrote:
The way my shop is currently laid out, I’m only able to get about 10” of cut capacity on the parallel fence before the planer gets in the way. That’s the downside of using the parallel fence attachment in a smaller shop as things often get in the way.? <image0.jpeg><image1.jpeg>
On Mar 12, 2022, at 9:19 PM, Dan Gavrilyuk via <dgwoodco@...> wrote:
? Here’s how the measuring part attaches to the support. It seems like you’ll probably just need to purchase some kipp levers and you should be able to make it work. How long is your support table attachment? The standard one on the parallel fence is 31.5” long. If yours is shorter then you’ll have to trim the measurement part most likely.? <image0.jpeg><image1.jpeg><image2.jpeg><image3.jpeg>
? Bill, Thanks for the length and pics.
To people who are familiar with Felder parallel fence, could?I attach the bracket of the rod with scale (from the parallel fence) to the end plate of this extension table that I have for use as a parallel fence? not sure if it is secured properly as it is attached with a single bolt at bottom.
<image0.jpeg>
<image1.jpeg>
The end of the this extension is almost 33” from blade so I understand that I will not be able to use the full range.
BTW, what are the cases where one would need the 50” range. I cannot imagine parallel ripping more than 12” wide regularly. So if you have a 36”+ wide piece and would like to rip into three 12” wide boards, would you not prefer to set the parallel fence once to 12”, clamp the piece and rip a 12” board and repeat.
Imran? On Mar 12, 2022, at 5:01 PM, Bill Belanger < Bill@...> wrote: ? 1290 long <image_123927839.JPG> <image_123927839.JPG> <image_123927839.JPG> Hi Bill,
How long the the extrusion with scale and can you share a pic of the bracket by the reticle? I would like to figure out how I can attach it to an ext table and use it. Imran? On Mar 12, 2022, at 1:08 PM, Bill Belanger < Bill@...> wrote: ?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
Sounds like maybe a 5/16” t-bolt could work in that groove, maybe?
Wade
toggle quoted message
Show quoted text
On Mar 12, 2022, at 6:28 PM, Dan Gavrilyuk <dgwoodco@...> wrote:
? Wade those are 13.4 mm on the bottom, 8.6mm on the top, 6mm deep groove under the lip, and 9mm deep overall? On Mar 12, 2022, at 9:26 PM, Dan Gavrilyuk via groups.io <dgwoodco@...> wrote:
? ? The way my shop is currently laid out, I’m only able to get about 10” of cut capacity on the parallel fence before the planer gets in the way. That’s the downside of using the parallel fence attachment in a smaller shop as things often get in the way.?
On Mar 12, 2022, at 9:19 PM, Dan Gavrilyuk via groups.io <dgwoodco@...> wrote:
? Here’s how the measuring part attaches to the support. It seems like you’ll probably just need to purchase some kipp levers and you should be able to make it work. How long is your support table attachment? The standard one on the parallel fence is 31.5” long. If yours is shorter then you’ll have to trim the measurement part most likely.?
On Mar 12, 2022, at 9:02 PM, imranindiana <imranindiana@...> wrote:
? Bill, Thanks for the length and pics.
To people who are familiar with Felder parallel fence, could?I attach the bracket of the rod with scale (from the parallel fence) to the end plate of this extension table that I have for use as a parallel fence? not sure if it is secured properly as it is attached with a single bolt at bottom.
The end of the this extension is almost 33” from blade so I understand that I will not be able to use the full range.
BTW, what are the cases where one would need the 50” range. I cannot imagine parallel ripping more than 12” wide regularly. So if you have a 36”+ wide piece and would like to rip into three 12” wide boards, would you not prefer to set the parallel fence once to 12”, clamp the piece and rip a 12” board and repeat.
Imran?
On Mar 12, 2022, at 5:01 PM, Bill Belanger <Bill@...> wrote:
? 1290 long Hi Bill,
How long the the extrusion with scale and can you share a pic of the bracket by the reticle? I would like to figure out how I can attach it to an ext table and use it. Imran? On Mar 12, 2022, at 1:08 PM, Bill Belanger < Bill@...> wrote: ?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Eagerly awaiting info on the new Felder FW 850...
Who sells Houfek in the U.S.?? I'm in northern California if it matters.
Thanks,
? ?Dennis
|
Jerry - you can do exactly that with my Fritz and Franz jig.? You can set the stop on the front scale to the desired location and then slide up the back portion and set its stop exactly the same as the front to get a parallel cut.? In practice, I find my stops to be quite accurate so I can use the scale on both stops and set them to the same value independently and I'll get a parallel cut. I believe this is what Tim showed in his photos in a previous post and he is within 0.001"
David
|
Re: Felder parallel fence
Glad I was able to help. I’m not surprised that it’s the same extrusion, wouldn’t make sense for felder to make/sell a different extrusion for that parallel fence attachment vs the shorter table support.?
toggle quoted message
Show quoted text
On Mar 12, 2022, at 9:32 PM, imranindiana <imranindiana@...> wrote:
? Dan,
I did not expect it but my extrusion is same behind the cover plate. Would need to tap the AL for for kip levers. My table is 19 3/4” so the range will be limited but enough for me.
Imran
On Mar 12, 2022, at 9:19 PM, Dan Gavrilyuk <dgwoodco@...> wrote:
? Here’s how the measuring part attaches to the support. It seems like you’ll probably just need to purchase some kipp levers and you should be able to make it work. How long is your support table attachment? The standard one on the parallel fence is 31.5” long. If yours is shorter then you’ll have to trim the measurement part most likely.?
On Mar 12, 2022, at 9:02 PM, imranindiana <imranindiana@...> wrote:
? Bill, Thanks for the length and pics.
To people who are familiar with Felder parallel fence, could?I attach the bracket of the rod with scale (from the parallel fence) to the end plate of this extension table that I have for use as a parallel fence? not sure if it is secured properly as it is attached with a single bolt at bottom.
The end of the this extension is almost 33” from blade so I understand that I will not be able to use the full range.
BTW, what are the cases where one would need the 50” range. I cannot imagine parallel ripping more than 12” wide regularly. So if you have a 36”+ wide piece and would like to rip into three 12” wide boards, would you not prefer to set the parallel fence once to 12”, clamp the piece and rip a 12” board and repeat.
Imran?
On Mar 12, 2022, at 5:01 PM, Bill Belanger <Bill@...> wrote:
? 1290 long Hi Bill,
How long the the extrusion with scale and can you share a pic of the bracket by the reticle? I would like to figure out how I can attach it to an ext table and use it. Imran? On Mar 12, 2022, at 1:08 PM, Bill Belanger < Bill@...> wrote: ?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
Dan,
I did not expect it but my extrusion is same behind the cover plate. Would need to tap the AL for for kip levers. My table is 19 3/4” so the range will be limited but enough for me.
Imran
toggle quoted message
Show quoted text
On Mar 12, 2022, at 9:19 PM, Dan Gavrilyuk <dgwoodco@...> wrote: ? Here’s how the measuring part attaches to the support. It seems like you’ll probably just need to purchase some kipp levers and you should be able to make it work. How long is your support table attachment? The standard one on the parallel fence is 31.5” long. If yours is shorter then you’ll have to trim the measurement part most likely.?
On Mar 12, 2022, at 9:02 PM, imranindiana <imranindiana@...> wrote:
? Bill, Thanks for the length and pics.
To people who are familiar with Felder parallel fence, could?I attach the bracket of the rod with scale (from the parallel fence) to the end plate of this extension table that I have for use as a parallel fence? not sure if it is secured properly as it is attached with a single bolt at bottom.
The end of the this extension is almost 33” from blade so I understand that I will not be able to use the full range.
BTW, what are the cases where one would need the 50” range. I cannot imagine parallel ripping more than 12” wide regularly. So if you have a 36”+ wide piece and would like to rip into three 12” wide boards, would you not prefer to set the parallel fence once to 12”, clamp the piece and rip a 12” board and repeat.
Imran?
On Mar 12, 2022, at 5:01 PM, Bill Belanger <Bill@...> wrote:
? 1290 long Hi Bill,
How long the the extrusion with scale and can you share a pic of the bracket by the reticle? I would like to figure out how I can attach it to an ext table and use it. Imran? On Mar 12, 2022, at 1:08 PM, Bill Belanger < Bill@...> wrote: ?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
Wade those are 13.4 mm on the bottom, 8.6mm on the top, 6mm deep groove under the lip, and 9mm deep overall?
toggle quoted message
Show quoted text
On Mar 12, 2022, at 9:26 PM, Dan Gavrilyuk via groups.io <dgwoodco@...> wrote:
? ? The way my shop is currently laid out, I’m only able to get about 10” of cut capacity on the parallel fence before the planer gets in the way. That’s the downside of using the parallel fence attachment in a smaller shop as things often get in the way.?
On Mar 12, 2022, at 9:19 PM, Dan Gavrilyuk via groups.io <dgwoodco@...> wrote:
? Here’s how the measuring part attaches to the support. It seems like you’ll probably just need to purchase some kipp levers and you should be able to make it work. How long is your support table attachment? The standard one on the parallel fence is 31.5” long. If yours is shorter then you’ll have to trim the measurement part most likely.?
On Mar 12, 2022, at 9:02 PM, imranindiana <imranindiana@...> wrote:
? Bill, Thanks for the length and pics.
To people who are familiar with Felder parallel fence, could?I attach the bracket of the rod with scale (from the parallel fence) to the end plate of this extension table that I have for use as a parallel fence? not sure if it is secured properly as it is attached with a single bolt at bottom.
The end of the this extension is almost 33” from blade so I understand that I will not be able to use the full range.
BTW, what are the cases where one would need the 50” range. I cannot imagine parallel ripping more than 12” wide regularly. So if you have a 36”+ wide piece and would like to rip into three 12” wide boards, would you not prefer to set the parallel fence once to 12”, clamp the piece and rip a 12” board and repeat.
Imran?
On Mar 12, 2022, at 5:01 PM, Bill Belanger <Bill@...> wrote:
? 1290 long Hi Bill,
How long the the extrusion with scale and can you share a pic of the bracket by the reticle? I would like to figure out how I can attach it to an ext table and use it. Imran? On Mar 12, 2022, at 1:08 PM, Bill Belanger < Bill@...> wrote: ?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
? The way my shop is currently laid out, I’m only able to get about 10” of cut capacity on the parallel fence before the planer gets in the way. That’s the downside of using the parallel fence attachment in a smaller shop as things often get in the way.?
toggle quoted message
Show quoted text
On Mar 12, 2022, at 9:19 PM, Dan Gavrilyuk via groups.io <dgwoodco@...> wrote:
? Here’s how the measuring part attaches to the support. It seems like you’ll probably just need to purchase some kipp levers and you should be able to make it work. How long is your support table attachment? The standard one on the parallel fence is 31.5” long. If yours is shorter then you’ll have to trim the measurement part most likely.?
On Mar 12, 2022, at 9:02 PM, imranindiana <imranindiana@...> wrote:
? Bill, Thanks for the length and pics.
To people who are familiar with Felder parallel fence, could?I attach the bracket of the rod with scale (from the parallel fence) to the end plate of this extension table that I have for use as a parallel fence? not sure if it is secured properly as it is attached with a single bolt at bottom.
The end of the this extension is almost 33” from blade so I understand that I will not be able to use the full range.
BTW, what are the cases where one would need the 50” range. I cannot imagine parallel ripping more than 12” wide regularly. So if you have a 36”+ wide piece and would like to rip into three 12” wide boards, would you not prefer to set the parallel fence once to 12”, clamp the piece and rip a 12” board and repeat.
Imran?
On Mar 12, 2022, at 5:01 PM, Bill Belanger <Bill@...> wrote:
? 1290 long Hi Bill,
How long the the extrusion with scale and can you share a pic of the bracket by the reticle? I would like to figure out how I can attach it to an ext table and use it. Imran? On Mar 12, 2022, at 1:08 PM, Bill Belanger < Bill@...> wrote: ?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
The way my shop is currently laid out, I’m only able to get about 10” of cut capacity on the parallel fence before the planer gets in the way. That’s the downside of using the parallel fence attachment in a smaller shop as things often get in the way.?
toggle quoted message
Show quoted text
On Mar 12, 2022, at 9:19 PM, Dan Gavrilyuk via groups.io <dgwoodco@...> wrote:
? Here’s how the measuring part attaches to the support. It seems like you’ll probably just need to purchase some kipp levers and you should be able to make it work. How long is your support table attachment? The standard one on the parallel fence is 31.5” long. If yours is shorter then you’ll have to trim the measurement part most likely.?
On Mar 12, 2022, at 9:02 PM, imranindiana <imranindiana@...> wrote:
? Bill, Thanks for the length and pics.
To people who are familiar with Felder parallel fence, could?I attach the bracket of the rod with scale (from the parallel fence) to the end plate of this extension table that I have for use as a parallel fence? not sure if it is secured properly as it is attached with a single bolt at bottom.
The end of the this extension is almost 33” from blade so I understand that I will not be able to use the full range.
BTW, what are the cases where one would need the 50” range. I cannot imagine parallel ripping more than 12” wide regularly. So if you have a 36”+ wide piece and would like to rip into three 12” wide boards, would you not prefer to set the parallel fence once to 12”, clamp the piece and rip a 12” board and repeat.
Imran?
On Mar 12, 2022, at 5:01 PM, Bill Belanger <Bill@...> wrote:
? 1290 long Hi Bill,
How long the the extrusion with scale and can you share a pic of the bracket by the reticle? I would like to figure out how I can attach it to an ext table and use it. Imran? On Mar 12, 2022, at 1:08 PM, Bill Belanger < Bill@...> wrote: ?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
Dan,
I’m curious, what size are those t-slots in the support table?
Thx,
Wade
toggle quoted message
Show quoted text
On Mar 12, 2022, at 6:19 PM, Dan Gavrilyuk <dgwoodco@...> wrote:
? Here’s how the measuring part attaches to the support. It seems like you’ll probably just need to purchase some kipp levers and you should be able to make it work. How long is your support table attachment? The standard one on the parallel fence is 31.5” long. If yours is shorter then you’ll have to trim the measurement part most likely.?
On Mar 12, 2022, at 9:02 PM, imranindiana <imranindiana@...> wrote:
? Bill, Thanks for the length and pics.
To people who are familiar with Felder parallel fence, could?I attach the bracket of the rod with scale (from the parallel fence) to the end plate of this extension table that I have for use as a parallel fence? not sure if it is secured properly as it is attached with a single bolt at bottom.
The end of the this extension is almost 33” from blade so I understand that I will not be able to use the full range.
BTW, what are the cases where one would need the 50” range. I cannot imagine parallel ripping more than 12” wide regularly. So if you have a 36”+ wide piece and would like to rip into three 12” wide boards, would you not prefer to set the parallel fence once to 12”, clamp the piece and rip a 12” board and repeat.
Imran?
On Mar 12, 2022, at 5:01 PM, Bill Belanger <Bill@...> wrote:
? 1290 long Hi Bill,
How long the the extrusion with scale and can you share a pic of the bracket by the reticle? I would like to figure out how I can attach it to an ext table and use it. Imran? On Mar 12, 2022, at 1:08 PM, Bill Belanger < Bill@...> wrote: ?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
Here’s how the measuring part attaches to the support. It seems like you’ll probably just need to purchase some kipp levers and you should be able to make it work. How long is your support table attachment? The standard one on the parallel fence is 31.5” long. If yours is shorter then you’ll have to trim the measurement part most likely.?
toggle quoted message
Show quoted text
On Mar 12, 2022, at 9:02 PM, imranindiana <imranindiana@...> wrote:
? Bill, Thanks for the length and pics.
To people who are familiar with Felder parallel fence, could?I attach the bracket of the rod with scale (from the parallel fence) to the end plate of this extension table that I have for use as a parallel fence? not sure if it is secured properly as it is attached with a single bolt at bottom.
The end of the this extension is almost 33” from blade so I understand that I will not be able to use the full range.
BTW, what are the cases where one would need the 50” range. I cannot imagine parallel ripping more than 12” wide regularly. So if you have a 36”+ wide piece and would like to rip into three 12” wide boards, would you not prefer to set the parallel fence once to 12”, clamp the piece and rip a 12” board and repeat.
Imran?
On Mar 12, 2022, at 5:01 PM, Bill Belanger <Bill@...> wrote:
? 1290 long Hi Bill,
How long the the extrusion with scale and can you share a pic of the bracket by the reticle? I would like to figure out how I can attach it to an ext table and use it. Imran? On Mar 12, 2022, at 1:08 PM, Bill Belanger < Bill@...> wrote: ?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
I hear yah Dan, its too bad Felder doesn’t offer that longer support table as a separate item anymore, or else I could use Bill’s scale rod. ?I’m going to order Lambs fence, most likely the analog log version. ?I trying to think if I’d ever regret not getting the DRO version though. ?I have DRO’s on my large crosscut fence already. ?So I would just use those to set the parallel fence.
Wade
toggle quoted message
Show quoted text
On Mar 12, 2022, at 5:53 PM, Dan Gavrilyuk <dgwoodco@...> wrote:
? I do the same as Bill, the measuring devise lives on a shelf most of the time so far.? On Mar 12, 2022, at 8:36 PM, Wade Dees <wjdsignature@...> wrote:
? Ah, okay. ?Thanks Bill On Mar 12, 2022, at 5:29 PM, Bill Belanger <Bill@...> wrote:
? Just the rod/measuring device. I use the platform to support plywood.
Bill Bélanger
Bill,
Can’t remember if this was a completely parallel fence or just the stop rod?
Thx,
Wade On Mar 12, 2022, at 10:08 AM, Bill Belanger <Bill@...> wrote:
?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
Bill, Thanks for the length and pics.
To people who are familiar with Felder parallel fence, could?I attach the bracket of the rod with scale (from the parallel fence) to the end plate of this extension table that I have for use as a parallel fence? not sure if it is secured properly as it is attached with a single bolt at bottom.
The end of the this extension is almost 33” from blade so I understand that I will not be able to use the full range.
BTW, what are the cases where one would need the 50” range. I cannot imagine parallel ripping more than 12” wide regularly. So if you have a 36”+ wide piece and would like to rip into three 12” wide boards, would you not prefer to set the parallel fence once to 12”, clamp the piece and rip a 12” board and repeat.
Imran?
toggle quoted message
Show quoted text
On Mar 12, 2022, at 5:01 PM, Bill Belanger <Bill@...> wrote: ? 1290 long Hi Bill,
How long the the extrusion with scale and can you share a pic of the bracket by the reticle? I would like to figure out how I can attach it to an ext table and use it. Imran? On Mar 12, 2022, at 1:08 PM, Bill Belanger < Bill@...> wrote: ?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
I do the same as Bill, the measuring devise lives on a shelf most of the time so far.?
toggle quoted message
Show quoted text
On Mar 12, 2022, at 8:36 PM, Wade Dees <wjdsignature@...> wrote:
? Ah, okay. ?Thanks Bill On Mar 12, 2022, at 5:29 PM, Bill Belanger <Bill@...> wrote:
? Just the rod/measuring device. I use the platform to support plywood.
Bill Bélanger
Bill,
Can’t remember if this was a completely parallel fence or just the stop rod?
Thx,
Wade On Mar 12, 2022, at 10:08 AM, Bill Belanger <Bill@...> wrote:
?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
toggle quoted message
Show quoted text
On Mar 12, 2022, at 5:29 PM, Bill Belanger <Bill@...> wrote:
? Just the rod/measuring device. I use the platform to support plywood.
Bill Bélanger
Bill,
Can’t remember if this was a completely parallel fence or just the stop rod?
Thx,
Wade On Mar 12, 2022, at 10:08 AM, Bill Belanger <Bill@...> wrote:
?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
Just the rod/measuring device. I use the platform to support plywood.
Bill Bélanger
toggle quoted message
Show quoted text
Bill,
Can’t remember if this was a completely parallel fence or just the stop rod?
Thx,
Wade On Mar 12, 2022, at 10:08 AM, Bill Belanger <Bill@...> wrote:
?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Re: Felder parallel fence
Bill,
Can’t remember if this was a completely parallel fence or just the stop rod?
Thx,
Wade
toggle quoted message
Show quoted text
On Mar 12, 2022, at 10:08 AM, Bill Belanger <Bill@...> wrote:
?Mike has decided his base is too short for the readout so if anyone else needs it make me an offer. Bill Belanger
|
Dan Gavrilyuk
imran
Bill Belanger