开云体育

Watch e bay they are selling pretty cheep one went last week for $2,000.00! martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330 cell airtightclamps@...

Does anyone have a copy of The Unofficial Survival Guide by David Best. I am happy to pay for it, but its no longer in print and there is no where to buy it from.

With a narrow pallet jack I found no issues with getting my ad941, k700s and the k940s off the pallets by myself. I was actually surprised at how easy it was, I thought for sure I was going to run

Mitch, You can connect power to A1 & A2. do not connect any thing to dust collector. Confirm 15 & 16 are shorted and there is an open between 15 & 18. Now turn a machine on that has the coil

I used an engine hoist to get my B3 off the pallet (video: https://youtu.be/9WpjWxJxRUg ). Tip the driver if he's willing to put them in your garage/shop. Tenryu blades are nice. -- Bill Hope (

Dino, Are the blades sharp? What happens if you increase the feed rate. Light cuts at very slow feed can dull the blades. If you did not mention labored sound, I would have thought a limit switch or

Many of us here have standardized on Tenryu 300mm blades like this:

Thank you all for the responses. They are very helpful. I ordered clamps from Mac about 3 weeks ago so they are due to show get here a few weeks after the machines. Looks like I need to get my hands

No, it doesn’t, Annu. It injects DC into the motor winding. Roger

Mitch, This is best I can think of. Maybe someone here will confirm. Run it by Felder before implementing it. Imran Sent: Saturday, January 09, 2021 8:12 PM To: [email protected] Subject:

Chris Perren's recommendations are spot- on. Be sure to get a NARROW pallet jack, regulars won't fit under many pieces of Felder kit. Mac's clamps are an "expensive option" when you are

Imran, The dust collector motor is single phase and thus uses just two of the available 3 input lines at the contactor. The contactor is controlled by 240V for switching on/off. Thanks, Mitch

* Get a Pallet Jack * Make sure you have 220 drops and DC ducting ready. * Standardize on [TENRYU IW-30050CBD3] 300mm Saw Blade -->

I'll second that, the machines are HEAVY. Depending where you've got to move them to you might consider hiring a rigging company. Do you have the duct work plan all squared away for your dust

Hey All, the caps will be in on Tuesday so I find out then. Cliff, It had a electronic brake that is supposed to stop everything from spinning within 10-12 seconds of hitting the stop button. ?I

When they say "drop ship", that's exactly what they mean. They'll unload the pallet from their lift gate and leave it for you to figure out. Supposedly, a narrow pallet jack makes transporting the

New to the group. I have a delivery of 4 new machines due in 4 weeks (KF700, FB510, RL160, and Hammer A3-41. I am just a hobbist and am new to both sliders and Felder but after much research chose to

cmluck, I assume your dust collector motor is 3 phase since you mention it is controlled by a 3 phase contactor. How is this contactor switched? 110AC or 220AC or some DC voltage? I can at least

I would add, many times trying to get everything lined up perfectly on a machine is not always necessary(within reason). The best test is if the machine cuts straight, flat, and evenly. If the jointer

Greetings to all, I recently purchased, from Felder, a ZIEHL STW1K S225636 Dust Collector Control Module along with a few of the ZIEHL STWA1 Coil Transformers to control my dust collector. This module