开云体育

I highly recommend the Alpine Workshop with Joe Calhoun, especially for anyone who is just starting with a shaper. It’s four days in his shop. Joe has all the patience in the world and is very

Here’s my take on this. The Felder feeder has manual (not magnetic) on-off switch. If the switch is left on, the feeder comes on with the shaper motor. I believe the Comatic has a magnetic or

Previously I had an F48 Felder power feeder connected to the shaper with the same connection, and it stopped and started with the shaper motor. I haven’t looked into the reason for the change, as I,

Andy, Could you post a picture for your Hammer tilt bracket with the gas spring from McMaster? I want to see how you mount the gas spring on the bracket. I have Felder tilt bracket. Thanks, James

I've been using a Comatic DC40 with the standard stand (ie the dumb one) on my C3 using the Hammer tilt bracket and a gas spring I got from McMaster for about a year with zero issues. Obviously the

When I was in that show room the last time, there was either a KF 700 (not sure if it is SP or not) or a K 700 S on display. It has the gray/blue paint job. I was there to take some real-time

Hi Joe, I asked Liz Rogers to add item 430-017 "Titling device "F" with gas spring" to the quote. I look at the picture in the Felder catalog and have doubt about its utility since it looks kinda

How else would you do it! martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330 cell 608-824-0023 fax airtightclamps@... airtightclamps.com Designing and

Hi Corey, The big tenon cutters are part of a Leitz Euro window set. The max depth of tenon is about 90mm. Since the big tenon cutters are part of a window set and are made to make crossed lapped

David, Ha! You are correct of course. I disliked the Felder feeder plug for the wrong reason and now dislike it even more. So there is delayed power to the feeder then it still has to be turned on

HI Joe, what 300mm tenon cutter did you purchase? Max length of tenon? Cost? I've been looking for similar for big door tenons and smaller timber work like gate projects. 5" tenon would even be more

You guys are funny. OCD has it’s advantages and disadvantages. And people vary a great deal in terms of their need for organization and keeping the shop clean and tidy. When I’m busy with a

Thanks for training Liz. I’m sure many others will appreciate your efforts, although they’ll probably never know what you did to enhance her job security. LOL And congratulations on your purchase.

Oh baby, you guys got your nickers in a knot over my misspeak! Sorry. :-) Correct David, my feeder powers up, but does not actually start feeding automatically. So I used the phrase "it turns on" in

I ordered my Profil with provisions to provide power for the feeder which it does well. The outlet is on the back left side just below the second dust port and uses a European style plug which is

Yep another great recommendation on Mac's clamps. Air clamps are IMHO a must upgrade. Also adding Brian Lamb's parallel cutting setup. Both are essential to how I operate. Joe Jensen | VP Internet of

He must have a night shift that cleans the place. I hope when i get set up in my shop I can keep it as clean as his.

I highly recommend that you consider the Aigner fence. It allows you to easily cover most of the opening between fences when shaping. It's expensive but I consider it the best upgrade I made when

It sounds like you think a 10HP motor automatically uses up the capacity of a 10HP PP. This is not that case. The PP rating is the maximum load it supports, expressed for convenience in HP, but a more

I have a Comatic DC40 on a smart feeder on a 2009 KF700SP on the Felder tilt bracket with a self-built big lift type gas strut. The 4 wheel is large and heavy and I would never be able to flip it