FS 2002 Full EuroVan Camper $20,000
Van is available in mid May, 2023.
We will deliver anywhere between Texas and Michigan.?
We are taking our last trip in our well-maintained 2002 full EuroVan Camper, so we are now selling our great camper van.
We are retired & non-smokers (clean van). The odometer reads about 185,000 miles.
The stove & sink both work. Not sure about the fridge, we rarely use it.
The AC works fine & the transmission shifts smoothly; we have frequently changed all the engine fluids & filters including the transmission fluid and filter. This is important with EuroVans.
We have never used the furnace; but it did work when we purchased the van.
Replaced during our ownership: Complete exhaust,? Engine water pump,? Rebuilt AC compressor,? Brake pads,?? New tires: about 10,000 miles ago, Fuel Vapor Evaporator Charcoal Canister.
Extras include: EuroVan Side Awning, Audi Wheels, Carpeting, Seat covers, Many camping/kitchen items, ScanGuage (important for monitoring the engine), Auxiliary Transmission fluid cooler, (Important for keeping the transmission fluid from overheating), Transmission fluid dipstick, External 110 V power cord, Tire jack, Both the EuroVan's owner's manual and the Winnebago owner's manual, Van Cover (to be mailed when I arrive in Michigan)
On the 20-year-old vehicle there are a few items that don't work quite so well: The rear clothes closet sliding door does not latch well, One of the pop-top roof lights does not work, There are a few minor scrapes and scratches around the interior and exterior of the van, Some discolored streeks on the pop top canvas. Slight crack in left rear taillight. Driver's seat right armrest has come off, I do have the armrest though. Speaker grill on driver's door is cracked with quarter size piece missing. Some stains on the carpet. Fusebox cover is missing a frange. The self cancelling turn indicators don't always self cancel.
Malcolm. Phone +1 231-881-4591 Mwstebbins@...
Photos can be viewed here:
? Eurovan For Sale Shared with Dropbox
|
Re: Weatherproof car cover
I¡¯d be happy to have it if you haven¡¯t yet found a home. I have a ¡®95 EVC and will be in the Bay Area this Friday. Perhaps I could pick it up, or if you prefer I can give you an address in Petaluma where I will be staying for ten days or so.
Thanks.
Jay Dwight
toggle quoted message
Show quoted text
On Mar 28, 2023, at 4:01 PM, george romero via groups.io <georgeromero@...> wrote:
?
Karey, If you still have the cover I¡¯d like it. I¡¯m in San Francisco and can pick it up. Also, I think you made the right move to a new vehicle. We¡¯re interested in how you like it. We park our 2001 ev camper in front of the house. I think the Metris is about the same size and might work for us. If you like I can also be contacted by phone or text at (415) 608-0758. Thank you, George
On Mar 28, 2023, at 10:31 AM, Karey Krauter <kek@...> wrote:
?Well, we finally made the leap to no longer owning a VW camper for the first time in my life. The latest, our 2002 EVC, 330K miles, never let us down, but we finally decided we needed to jump ship while the going was still good. I¡¯m hoping we have just started a student off on the same path I started on when I bought my first microbus as a student 50 years ago. All those generations of VW campers! Sorry that I couldn¡¯t wait any longer for the next generation.
Okay enough eulogizing! I have a eurovan camper extended-wheelbase weatherproof car cover, used once when when the van was new, when we then realized I couldn¡¯t manage it solo.
It¡¯s yours for the cost of shipping it to you. Let me know! I¡¯m in the San Francisco Bay Area.
(Also just in case there¡¯s anyone: the only other thing the student didn¡¯t take was a second set of Yakima roof racks, anyone want them? attaches to Yakima roof mountings, we got duplicated roof racks years ago, dumb story.)
/karey
(New owner of a GTRV Westy conversion on a Metris chassis, I¡¯m both very happy and very sad)
PS ha, you may be hearing from me again if the student doesn¡¯t come pick up this brand new pair of rear brake calipers I had shipping to me when the student took delivery, it needs them, but it¡¯s not my decision anymore!
|
Re: Weatherproof car cover
Karey,??
I am interested your extra Yakima roof racks.? More likely you can part them to someone much closer than shipping to Bellingham, WA.? We do have a close friend in San Franciso and we can pick them up in the future.
Riot of a story of van plus student and the unknown. Been there and will again no doubt.
Jim
94 Eurovan
|
Re: Replacement fuel lines for 1997 EVC
I had some headmaster work done. Drove my '97 90 miles and smelled gas,? The injectors were going so I had all replaced. Thrilling to see you have been doing 90 minutes then see gasoline gushing out.
Chandler, mine is the white one
|
I got mine at Home Depot. On Mar 28, 2023, at 3:57 PM, Jim 94 Eurovan < jim@...> wrote:
Cross Fingers, and reading in other threads here that the Suburban NT-16 SQ (not the NT-16SE Direct Exchange) will take the place of the original NT-12. The size and specs appear to be correct for the space and wiring.? It doesn't make sense to switch over to a Propex furnace and relocate everything.? Amazon, eBay, and other sellers didn't have one or were more expensive. In a few days, It will arrive and I hope to report back with a positive installation report
Adventure RV Center
2910 Newport Highway
Sevierville, TN 37876
Manufacturer's Number: 2444A NT-16SQ NT-16S NT-16SQT
$589.00?
12VDC 2.8 amp draw. Electronic ignition, gasket-sealed vent assemblies, steel gas manifolds, sealed forced-draft combustion, and chrome-plated vent caps.
N-16 Unit size: 9-3/8"H x 9-3/8"W x 21-27-3/8"D.? (Depth varies, depending on extension tubes which I don't anticipate using or at least not beyond the 24"D of the NT-12)
NT-12 Unit size; 9-1/2"H X 9 1/4 W X 23"D with exhaust vent connection 24" D (actual measurements in Van) Technical manual specs? 9-1/2"H X 8"W X 24"D?
?
Another option is- NT-12 Repair kit, and replacement motor which may be the ticket.? I went with a new one so I wouldn't have to second guess if a nearly 30-year NT-12 was too far gone.
Great site for original installation manuals.
Jim 94 Eurovan
Christopher B. Volk Boise, Idaho
|
Re: Replacement fuel lines for 1997 EVC
That's my initial inclination to be sure.
Has anyone else tackled this task?
Kris
|
Re: Replacement fuel lines for 1997 EVC
Fabrication time
Buy a roll of high pressure fuel line from Napa and replace the leaky line
Stephen?
toggle quoted message
Show quoted text
On Mar 28, 2023, at 5:54 PM, Kris S. Seago <eljefeweizen@...> wrote:
? Howdy all,
My 1997 EVC started developing STRONG fuel odors in the cabin late last Fall. Life got busy and I parked it until I had time to devote to it. After a bit of exploratory surgery I located the source--there's a SERIOUS fuel leak in the supply line just past the fuel pump. It appears that the feed and return lines used to be available from VW as an assembly, but show as NLA at all the usual suspects.?
Feed- And Return Pipe 1 Set Of Fuel Lines In Pairs
7D0201080A
Suggestions?
Thanks in advance,
Kris S. Seago
|
Replacement fuel lines for 1997 EVC
Howdy all,
My 1997 EVC started developing STRONG fuel odors in the cabin late last Fall. Life got busy and I parked it until I had time to devote to it. After a bit of exploratory surgery I located the source--there's a SERIOUS fuel leak in the supply line just past the fuel pump. It appears that the feed and return lines used to be available from VW as an assembly, but show as NLA at all the usual suspects.?
Feed- And Return Pipe 1 Set Of Fuel Lines In Pairs
7D0201080A
Suggestions?
Thanks in advance,
Kris S. Seago
|
Re: Weatherproof car cover
?
Karey, If you still have the cover I¡¯d like it. I¡¯m in San Francisco and can pick it up. Also, I think you made the right move to a new vehicle. We¡¯re interested in how you like it. We park our 2001 ev camper in front of the house. I think the Metris is about the same size and might work for us. If you like I can also be contacted by phone or text at (415) 608-0758. Thank you, George
toggle quoted message
Show quoted text
On Mar 28, 2023, at 10:31 AM, Karey Krauter <kek@...> wrote:
?Well, we finally made the leap to no longer owning a VW camper for the first time in my life. The latest, our 2002 EVC, 330K miles, never let us down, but we finally decided we needed to jump ship while the going was still good. I¡¯m hoping we have just started a student off on the same path I started on when I bought my first microbus as a student 50 years ago. All those generations of VW campers! Sorry that I couldn¡¯t wait any longer for the next generation.
Okay enough eulogizing! I have a eurovan camper extended-wheelbase weatherproof car cover, used once when when the van was new, when we then realized I couldn¡¯t manage it solo.
It¡¯s yours for the cost of shipping it to you. Let me know! I¡¯m in the San Francisco Bay Area.
(Also just in case there¡¯s anyone: the only other thing the student didn¡¯t take was a second set of Yakima roof racks, anyone want them? attaches to Yakima roof mountings, we got duplicated roof racks years ago, dumb story.)
/karey
(New owner of a GTRV Westy conversion on a Metris chassis, I¡¯m both very happy and very sad)
PS ha, you may be hearing from me again if the student doesn¡¯t come pick up this brand new pair of rear brake calipers I had shipping to me when the student took delivery, it needs them, but it¡¯s not my decision anymore!
|
Cross Fingers, and reading in other threads here that the Suburban NT-16 SQ (not the NT-16SE Direct Exchange) will take the place of the original NT-12. The size and specs appear to be correct for the space and wiring.? It doesn't make sense to switch over to a Propex furnace and relocate everything.? Amazon, eBay, and other sellers didn't have one or were more expensive. In a few days, It will arrive and I hope to report back with a positive installation report Adventure RV Center
2910 Newport Highway
Sevierville, TN 37876
Manufacturer's Number: 2444A NT-16SQ NT-16S NT-16SQT
$589.00?
12VDC 2.8 amp draw. Electronic ignition, gasket-sealed vent assemblies, steel gas manifolds, sealed forced-draft combustion, and chrome-plated vent caps.
N-16 Unit size: 9-3/8"H x 9-3/8"W x 21-27-3/8"D.? (Depth varies, depending on extension tubes which I don't anticipate using or at least not beyond the 24"D of the NT-12)
NT-12 Unit size; 9-1/2"H X 9 1/4 W X 23"D with exhaust vent connection 24" D (actual measurements in Van) Technical manual specs? 9-1/2"H X 8"W X 24"D?
Another option is- NT-12 Repair kit, and replacement motor which may be the ticket.? I went with a new one so I wouldn't have to second guess if a nearly 30-year NT-12 was too far gone.
https://pdxrvwholesale.com/products/suburban-furnace-model-nt-12s-tune-up-kit
Great site for original installation manuals.
http://techsupport.pdxrvwholesale.com/wp-content/uploads/2018/12/Suburban-Dyna-Trail-Installation-Operating-and-Service-Instructions-NT-12.pdf
http://techsupport.pdxrvwholesale.com/wp-content/uploads/2017/12/Suburban-Furnace-User-Information-Manual-nt16sq-nt20sq.pdf
Jim 94 Eurovan
?
|
Re: Body work in Seattle area
Werner¡¯s Crash Shop has always been wonderful. Lower Queen Anne.?
Jim- 94 Eurovan
|
Re: Body work in Seattle area
I did the same. ?Little odd driving without a windshield?
toggle quoted message
Show quoted text
On Mar 28, 2023, at 3:06 PM, Wigen via groups.io <chenely63@...> wrote:
?When I had my windshield replaced , ?safelite took mine out ?and I took it home and fixed the rust than made appointment to have windshield put in.
leo 1998
|
Re: Body work in Seattle area
When I had my windshield replaced , ?safelite took mine out ?and I took it home and fixed the rust than made appointment to have windshield put in.
leo 1998
|
Re: Body work in Seattle area
Steve Krival wrote: I also have rust bubbles and live in Seattle. If you figure out a solution, let us know! I live in Minnesota, where we get a lot of rust from salty winter roads. As soon as there is a tiny chip in the paint, the salt gets in and starts working on the metal underneath. It seems like some paints are prone to letting water wick in between the paint and the metal, where it can freeze. The expanding ice wedges even more paint free from the metal, creating a pocket for even more water to collect. The rust spreads underneath the paint, causing bubbles. I've never found a perfect solution as good as the factory; but POR-15 is the best I've found. This is a black paint that's designed to chemically bond to bare and rusted steel. I sand, wire-brush, or grind the metal as clean as possible, apply a couple coats of POR-15, and then a few coats of touch-up paint of the appropriate color. The resulting repair isn't as good as the factory finish, but at least it stops it from rusting further. <> Lee -- "All children are born engineers. Watch them at play. They're not just playing; they're experimenting, building and learning. That's engineering! Then we get them in school and squash it out of them." (Geoffrey Orsak, Southern Methodist University dean of engineering) -- Lee Hart, 814 8th Ave N, Sartell MN 56377, www.sunrise-ev.com -- This email has been checked for viruses by Avast antivirus software. www.avast.com
|
Re: Body work in Seattle area
I have the same question for the Mid Atlantic region (VA, WV, MD). Any
body shops there that you can recommend who would do that kind of work?
Thanks.
Wolfgang
toggle quoted message
Show quoted text
I also have rust bubbles and live in Seattle. If you figure out a solution
, let us know!.
Get Outlook for Android<>
________________________________
From: [email protected] <[email protected]> on behalf of
johnnystutsman via groups.io <johnnystutsman@...>
Sent: Monday, March 27, 2023 3:14:25 PM
To: [email protected] <[email protected]>
Subject: [eurovanupdate] Body work in Seattle area
Hello all,
I am trying to get the van ready for the up coming camping season. We
have an unrepairable ding in our windshield and will have to replace it.
We had a windshield replaced in the past and when they did it they must
have scratched something because I have some rust bubbles starting around
the windshield. I would like to get the rust repaired while I am getting
the windshield replaced. I would also like to take care of some other
cosmetic damage. I am wondering if there is anyone in the Seattle area
that people would recommend?
Thanks in advance,
Johnny - 2002 Weekender
|
Re: Weatherproof car cover
Hi Karey,
I¡¯ll help you out with the cover. Im in San Francisco Bay Area (Los Altos) so I may even be able to pick it up.
Let me know
Thanks
Susie
Sent from my electric nail-gun
toggle quoted message
Show quoted text
On Mar 28, 2023, at 10:31 AM, Karey Krauter <kek@...> wrote:
?Well, we finally made the leap to no longer owning a VW camper for the first time in my life. The latest, our 2002 EVC, 330K miles, never let us down, but we finally decided we needed to jump ship while the going was still good. I¡¯m hoping we have just started a student off on the same path I started on when I bought my first microbus as a student 50 years ago. All those generations of VW campers! Sorry that I couldn¡¯t wait any longer for the next generation.
Okay enough eulogizing! I have a eurovan camper extended-wheelbase weatherproof car cover, used once when when the van was new, when we then realized I couldn¡¯t manage it solo.
It¡¯s yours for the cost of shipping it to you. Let me know! I¡¯m in the San Francisco Bay Area.
(Also just in case there¡¯s anyone: the only other thing the student didn¡¯t take was a second set of Yakima roof racks, anyone want them? attaches to Yakima roof mountings, we got duplicated roof racks years ago, dumb story.)
/karey
(New owner of a GTRV Westy conversion on a Metris chassis, I¡¯m both very happy and very sad)
PS ha, you may be hearing from me again if the student doesn¡¯t come pick up this brand new pair of rear brake calipers I had shipping to me when the student took delivery, it needs them, but it¡¯s not my decision anymore!
|
Re: Body work in Seattle area
I also have rust bubbles and live in Seattle. If you figure out a solution , let us know!.
toggle quoted message
Show quoted text
Hello all,
I am trying to get the van ready for the up coming camping season.? We have an unrepairable ding in our windshield and will have to replace it.? We had a windshield replaced in the past and when they did it they must have scratched something because I have
some rust bubbles starting around the windshield.? I would like to get the rust repaired while I am getting the windshield replaced.? I would also like to take care of some other cosmetic damage.? I am wondering if there is anyone in the Seattle area that
people would recommend??
Thanks in advance,
Johnny - 2002 Weekender
|
Well, we finally made the leap to no longer owning a VW camper for the first time in my life. The latest, our 2002 EVC, 330K miles, never let us down, but we finally decided we needed to jump ship while the going was still good. I¡¯m hoping we have just started a student off on the same path I started on when I bought my first microbus as a student 50 years ago. All those generations of VW campers! Sorry that I couldn¡¯t wait any longer for the next generation.
Okay enough eulogizing! I have a eurovan camper extended-wheelbase weatherproof car cover, used once when when the van was new, when we then realized I couldn¡¯t manage it solo.
It¡¯s yours for the cost of shipping it to you. Let me know! I¡¯m in the San Francisco Bay Area.
(Also just in case there¡¯s anyone: the only other thing the student didn¡¯t take was a second set of Yakima roof racks, anyone want them? attaches to Yakima roof mountings, we got duplicated roof racks years ago, dumb story.)
/karey
(New owner of a GTRV Westy conversion on a Metris chassis, I¡¯m both very happy and very sad)
PS ha, you may be hearing from me again if the student doesn¡¯t come pick up this brand new pair of rear brake calipers I had shipping to me when the student took delivery, it needs them, but it¡¯s not my decision anymore!
|
Body work in Seattle area
Hello all,
I am trying to get the van ready for the up coming camping season.? We have an unrepairable ding in our windshield and will have to replace it.? We had a windshield replaced in the past and when they did it they must have scratched something because I have some rust bubbles starting around the windshield.? I would like to get the rust repaired while I am getting the windshield replaced.? I would also like to take care of some other cosmetic damage.? I am wondering if there is anyone in the Seattle area that people would recommend??
Thanks in advance,
Johnny - 2002 Weekender
|
Ah, that's the sensor you have to pull to check or fill the differential, I think.? I seem to remember some quirk about getting the connector off.? ?But an excellent opportunity to do that once in a lifetime gear oil change.?
|
Kris S. Seago
Lee Hart
Steve Krival