Re: Source for headlight lens
I have original headlights from '02 Eurovan/ Rialta...one lens looks to have small chip..otherwise they both worked...
Sent from my Verizon, Samsung Galaxy smartphone
Get
toggle quoted message
Show quoted text
I recently purchased new replacement headlights from Bus Depot, a little bit pricey but a much better brighter light than original?
On Wednesday, August 18, 2021, 07:23:45 AM EDT, sam letzring <sletz@...> wrote:
The glass lens is NLA from usual sources- but used assemblies are on EBay and plastic replacements are available from a number of sources including Amazon. Happy hunting!
Sam
02 EVC
On 8/17/2021 8:23 PM, worbneklip wrote:
Anyone have a recommendation for a source for a headlight lens for 2002 weekender? ?The body trim below the drivers side light also needs some help :). Driveway fender bender
matt?
durham nh
2002 weekender, 243k
|
The kit has been sold.
I guess the answer to my original question is that it is OK to post things for sale.
Paul
|
Re: Source for headlight lens
I recently purchased new replacement headlights from Bus Depot, a little bit pricey but a much better brighter light than original?
On Wednesday, August 18, 2021, 07:23:45 AM EDT, sam letzring <sletz@...> wrote:
The glass lens is NLA from usual sources- but used assemblies are
on EBay and plastic replacements are available from a number of
sources including Amazon. Happy hunting!
Sam
02 EVC
On 8/17/2021 8:23 PM, worbneklip wrote:
Anyone have a recommendation for a source for a headlight lens for
2002 weekender? ?The body trim below the drivers side light also
needs some help :). Driveway fender bender
matt?
durham nh
2002 weekender, 243k
|
Why not just include them with the vehicle?
|
Re: Source for headlight lens
Just Google 7D1941005A
and you can find some-BUT- you will wind up buying the whole
assembly- haven't found lenses yet.
Sam
On 8/17/2021 8:23 PM, worbneklip wrote:
toggle quoted message
Show quoted text
Anyone have a recommendation for a source for a headlight lens for
2002 weekender? ?The body trim below the drivers side light also
needs some help :). Driveway fender bender
matt?
durham nh
2002 weekender, 243k
|
Re: Source for headlight lens
The glass lens is NLA from usual sources- but used assemblies are
on EBay and plastic replacements are available from a number of
sources including Amazon. Happy hunting!
Sam
02 EVC
On 8/17/2021 8:23 PM, worbneklip wrote:
toggle quoted message
Show quoted text
Anyone have a recommendation for a source for a headlight lens for
2002 weekender? ?The body trim below the drivers side light also
needs some help :). Driveway fender bender
matt?
durham nh
2002 weekender, 243k
|
Source for headlight lens
Anyone have a recommendation for a source for a headlight lens for 2002 weekender? ?The body trim below the drivers side light also needs some help :). Driveway fender bender
matt?
durham nh
2002 weekender, 243k
|
Re: Bunting on cabin filter housing
I used some "stick-on" felt- available at fabric or craft stores.
Mice haven't bothered it.
sam
02EVC
On 8/17/2021 12:34 PM, Spencer Allen
wrote:
toggle quoted message
Show quoted text
Looks like a critter got to the fuzzy stuff covering the
cabin filter housing on my 02 weekender. I know other folks
here have had this problem and I want to know what everyone is
using to recover the housing. Anyone use some cloth thing like
the oem stuff?
Spencer
|
Bunting on cabin filter housing
Looks like a critter got to the fuzzy stuff covering the cabin filter housing on my 02 weekender. I know other folks here have had this problem and I want to know what everyone is using to recover the housing. Anyone use some cloth thing like the oem stuff? Spencer
|
toggle quoted message
Show quoted text
On Tue, Aug 17, 2021 at 10:58 AM Paul Lugo < pelbikes@...> wrote: I bought the E-code headlight Kit with "deluxe harness and relays" from Bus Depot (see ) last year but never got around to installing them. We are now going to sell our 93 Weekender and would like to sell this kit. I don't see a "for sale" section in this group so am wondering if it is OK to offer items for sale here.
Thanks,
Paul Lugo
|
I bought the E-code headlight Kit with "deluxe harness and relays" from Bus Depot (see ) last year but never got around to installing them. We are now going to sell our 93 Weekender and would like to sell this kit. I don't see a "for sale" section in this group so am wondering if it is OK to offer items for sale here.
Thanks,
Paul Lugo
|
Thank you very much, got it off and fixed locking issue
On Monday, August 16, 2021, 02:31:20 PM MDT, Michael Diehr <md03@...> wrote:
The sliding door is held on with a number of plastic press-to-fit connectors. One side is glued to the door panel, the other side connects to holes in the metal of the door. ?Removal is simply putting something thin between the panel and the metal and prying outward. ?
On my van, the glue holding one side came loose on about 75% of the pieces, and I had to glue them back on. ?Use a really strong glue or epoxy. ?I found a hot glue gun was not strong enough. ?
You can see 4 of the connectors in this picture, all of them came un-stuck:
On Aug 16, 2021, at 12:28 PM, Douglas Peterson via <dpeterson253@...> wrote:
Is there a video on how to remove the door panel anywhere? ?Following the Groups suggestions it appears all is working, lock moves up and?down, it just wont lock.
On Wednesday, July 14, 2021, 08:59:59 PM MDT, Douglas Peterson via <dpeterson253@...> wrote:
thanks
On Tuesday, July 13, 2021, 10:33:32 AM MDT, Carl Hansen <carl_hansen@...> wrote:
Locks are electric, not vacuum. ?Pull the door card and git to it. ?
Small white plastic clips
get brittle, levers disconnect, the electric pins (4) can get corroded.
Be careful pulling the door card off.
Ch
|
toggle quoted message
Show quoted text
On Aug 16, 2021, at 1:35 PM, Michael Diehr <md03@...> wrote:
?and here's a photo showing the back side - locations of all the fasteners have been circled (some are present, some came unglued and fell off): <PastedGraphic-2.tiff>
|
and here's a photo showing the back side - locations of all the fasteners have been circled (some are present, some came unglued and fell off): 
|
The sliding door is held on with a number of plastic press-to-fit connectors. One side is glued to the door panel, the other side connects to holes in the metal of the door. ?Removal is simply putting something thin between the panel and the metal and prying outward. ?
On my van, the glue holding one side came loose on about 75% of the pieces, and I had to glue them back on. ?Use a really strong glue or epoxy. ?I found a hot glue gun was not strong enough. ?
You can see 4 of the connectors in this picture, all of them came un-stuck:
On Aug 16, 2021, at 12:28 PM, Douglas Peterson via <dpeterson253@...> wrote:
Is there a video on how to remove the door panel anywhere? ?Following the Groups suggestions it appears all is working, lock moves up and?down, it just wont lock.
On Wednesday, July 14, 2021, 08:59:59 PM MDT, Douglas Peterson via <dpeterson253@...> wrote:
thanks
On Tuesday, July 13, 2021, 10:33:32 AM MDT, Carl Hansen <carl_hansen@...> wrote:
Locks are electric, not vacuum. ?Pull the door card and git to it. ?
Small white plastic clips
get brittle, levers disconnect, the electric pins (4) can get corroded.
Be careful pulling the door card off.
Ch
|
Is there a video on how to remove the door panel anywhere? ?Following the Groups suggestions it appears all is working, lock moves up and down, it just wont lock.
On Wednesday, July 14, 2021, 08:59:59 PM MDT, Douglas Peterson via groups.io <dpeterson253@...> wrote:
On Tuesday, July 13, 2021, 10:33:32 AM MDT, Carl Hansen <carl_hansen@...> wrote:
Locks are electric, not vacuum.? Pull the door card and git to it.?
Small white plastic clips
get brittle, levers disconnect, the electric pins (4) can get corroded.
Be careful pulling the door card off.
Ch
|
One of my EVs has a rusty hood latch cable that needs to be replaced. It caused the same problem where it wouldn't return enough to allow the hood to latch properly.? After some lubing and working it, I was able to juuuusssttt get it to latch.?
It could be that the battery install involved pushing or pulling on the release cable since it goes right over the top of the battery and could have been in the way.? I'd focus on the cable.
Good luck,
Kent
|
Alan,
Another possibility is that the battery was installed in such a way as to engage the hood unlock cable, so that the latch is always in the unlocked position.? It does indicate that an inspection of the battery installation area should be examined.? I'll go out and take a look at my 2000 GLS.? My battery is currently not installed.
v/r,
Mike?
|
On Sat, Aug 14, 2021 at 01:42 PM, alanbragg01730 wrote:
For whatever it's worth, I should note that this started happening after a local vw shop replaced the battery.
A somewhat remote possibility is that they damaged the hood release cable, preventing it from releasing completely. -- Duane 05HD Rialta 209K Miles
|
sometimes the mechanism in the hood needs clean?and lubed so that the spring in it can move it back to where it started.? It can get sticky and stay in the "open" position.
|
rdesjar897
Spencer Allen
Duane