HP Procurve 2520, I think. It's not the switches, although its odd that you have had to reboot your switch. I don't think I've ever had to reboot any of these switches. The problem was traced down to the bridge between the panel's comm with the processor and Core 3. We were able to debug that the panel was receiving the low level communication, but Core 3 wasn't receiving or reacting to the messages. At this point in the process, they had evidently reached the end of what they could debug... Heath Volmer Digital Domain Systems Littleton, CO Sent from my iTypo 4 On Apr 29, 2013, at 7:56 AM, jason santlofer <jason@...> wrote: Heath,
What kind of switches are you using Or have you tried?
Jason
Sent from my Verizon Wireless 4G LTE DROID
Heath Volmer <hvolmer@...> wrote:
I suspect that you'll find that they are still on line, and transmitting presses, but have stopped responding to feedback. If not, you've got a different problem than what many of us have been up against. I've been dealing with this for a while and the band-aid solution for now is to use the PERIODICREBOOT ON command to keep the things fresh every day. If someone needs multiple reboots per day, you may need to devise logic to console and issue reboot commands multiple times.
We've been through the "channels", all the way. No more channels to go through. They know that something is wrong. I had almost lost faith in my own ability to finish ;-).
Heath
On Apr 29, 2013, at 6:34 AM, jmgaudiovideo <jason@...> wrote:
Hi All,
Not not sure if this has been touched upon somewhere along the lines. I'm sure everyone has their stories about the new TSW-750 panels. I need some help. We have a couple of these systems in the field and both of them seem to have problems with the touchscreens just randomly freezing and falling off line. We have updated to just about every firmware Crestron has put out even some of the beta ones. We don't even have video running to the panels so I don't think it a memory issue. The only common denominator in the two systems is a Pakedge SW16-16PB ethernet switch which is powering the panels. It is a managed switch. On the larger job (10 tsw panels)the switch would actually freeze and need to be rebooted along with the CP3 processor to make them work again. On the other job the client says he just needs to reboot the panel to make them work. But he does so a couple times a day. We have gone through the channels at Crestron sent in code etc and they can't pinpoint a problem. I and our programmer have been working with Crestron product for quite a few years and never experienced these kind of problems before. Is anyone else experiencing these types of issues and if so were you able to solve them? My customers are increasingly losing faith in our ability to finish the job and honestly I am at a loss.
[Non-text portions of this message have been removed]
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links
[Non-text portions of this message have been removed]
|
Re: Samsung UE55ES7000 - EX-Link
From your screenshot, why are you using just the S+ module from inside the module without the whole Simpl wrapper? You should be using the whole module which contains the actual commmands. The S+ is only used to add the checksum and to send out the strings with varying parameters.
FWIW I have heard others reporting that the most recent crop of Samsungs aren't responding so reliably with Exlinx as they used to
OP
|
I've experienced the same issue while using Netgear switches.
I heard that there is a beta version of firmware available that fixes the issue, but I have not installed it myself. Has anyone actually seen and tested a "fixed" version of firmware for this problem?
toggle quoted message
Show quoted text
--- In Crestron@..., "m.nguyen" <mpninc@...> wrote:
I also have a Pakedge sw8-4pb
On Apr 29, 2013 7:19 AM, "m.nguyen" <mpninc@...> wrote:
I have the exact same problem and it is very random. I also have gone
thru all the Crestron channels and they have found nothing. I have told my
customer that if the panel lock up pull it from the wall and unplug the
cable and plug back.
On Apr 29, 2013 7:13 AM, "jason santlofer" <jason@...> wrote:
**
Heath,
What kind of switches are you using Or have you tried?
Jason
Sent from my Verizon Wireless 4G LTE DROID
Heath Volmer <hvolmer@...> wrote:
I suspect that you'll find that they are still on line, and transmitting presses, but have stopped responding to feedback. If not, you've got a
different problem than what many of us have been up against. I've been
dealing with this for a while and the band-aid solution for now is to use
the PERIODICREBOOT ON command to keep the things fresh every day. If
someone needs multiple reboots per day, you may need to devise logic to
console and issue reboot commands multiple times.
We've been through the "channels", all the way. No more channels to go
through. They know that something is wrong. I had almost lost faith in my
own ability to finish ;-).
Heath
On Apr 29, 2013, at 6:34 AM, jmgaudiovideo <jason@...> wrote:
Hi All,
Not not sure if this has been touched upon somewhere along the lines.
I'm sure everyone has their stories about the new TSW-750 panels. I need
some help. We have a couple of these systems in the field and both of them
seem to have problems with the touchscreens just randomly freezing and
falling off line. We have updated to just about every firmware Crestron has
put out even some of the beta ones. We don't even have video running to the
panels so I don't think it a memory issue. The only common denominator in
the two systems is a Pakedge SW16-16PB ethernet switch which is powering
the panels. It is a managed switch. On the larger job (10 tsw panels)the
switch would actually freeze and need to be rebooted along with the CP3
processor to make them work again. On the other job the client says he just
needs to reboot the panel to make them work. But he does so a couple times
a day. We have gone through the channels at Crestron sent in code etc and
they can't pinpoint a problem. I and our programmer have been working with
Crestron product for quite a few years and never experienced these kind of
problems before. Is anyone else experiencing these types of issues and if
so were you able to solve them? My customers are increasingly losing faith
in our ability to finish the job and honestly I am at a loss.
[Non-text portions of this message have been removed]
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the
Database area.
Yahoo! Groups Links
[Non-text portions of this message have been removed]
|
Re: Certification Changes
That's what I heard too Tony: new tests for Platinum and Gold, plus now Silver (no more frequent flyer trips for Silver). The offer was for a copy of the old-Gold test, so we could complete it "just for fun". It sounds like they are back to the "regular" Certification tests, but are working to improve the completion rates and reduce the back-check time. Both sound like good things to me!
Cameron
toggle quoted message
Show quoted text
--- In Crestron@..., "Tony Golden" <mrgolden@...> wrote:
I thought he was referring to the Gold test - which would make sense, since everyone at Masters would have already passed the Certification test :-)
--- In Crestron@..., "lincster2010" <lincster2010@> wrote:
IIRC, at Masters, Mr. O said people could get a copy of the old test, because the new test would be different.
--- In Crestron@..., "eagrubbs" <eagrubbs@> wrote:
I hope the test is different because that would be complete BS if it was the same test. A guy I work with that has not been to the 3rd class called crestron and was offered a copy of the test and got it. It was the same test I had. WTF? You mean you are giving out the test to anyone now without the time constraints the rest of us had. That really doesn't sound fair.
--- In Crestron@..., "doug_h_encinitas" <dghardy@> wrote:
I just finished 301 last week and on Friday the sent out an email saying they were changing the cert test. I got mine in an email yesterday. And looks and sounds like the old cert test. Even one of the questions I remember someone telling me last week about needing to use a 8 or 12 digit keypad with .wav playback function and sure enough it was this cert. if u want I can shoot u a copy of the scope, I don't think it will hurt to see what ur getting into.
--- In Crestron@..., "Mark" <dedicatedsystems@> wrote:
I am in my C301 class this week.
Seems they are changing the test process? Anyone know the details?
Apparently a email went out this morning to crestron employees that they are changing the test.....
Anyone know?
|
Re: TSW panels Gesture Canvas over buttons
Any way around this?
Currently media player does not work for everything.
Need a way to gesture up and down to browse list.
Select item when I get to it.
toggle quoted message
Show quoted text
On 4/29/13 10:48 AM, "Neil Dorin" <neildorin@...> wrote: Not currently. I made a request in labs about this some time ago I think.
I was hoping to use a gesture canvas to scroll "pages" on an icon list.
Maybe search on labs and add a request.
On Mon, Apr 29, 2013 at 8:41 AM, Seth Olle <seth@...> wrote:
**
Working on a TSW panel.
Can you put a gesture canvas over buttons?
Basically push through the gesture canvas to select buttons below it.
I am working on something where I will need the gesture up and down,
however I need buttons below to actually select items.
Is this possible? Hopefully I am just missing something?
Seth
[Non-text portions of this message have been removed]
------------------------------------
****
*
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the
Database area.
****
*Yahoo! Groups Links
|
Re: Wireless battery powered wall mounted keypad?
Actually, the product is made in Germany, so they have all kinds of international form factors.
Check this out
Sent from my mobile pocket warmer.
|
Re: Certification Changes
Ottesen, lord I hope that is the correct spelling, actually stated you could get a copy of all the old tests. The only problem is now the old tests are current tests.
toggle quoted message
Show quoted text
--- In Crestron@..., "Tony Golden" <mrgolden@...> wrote:
I thought he was referring to the Gold test - which would make sense, since everyone at Masters would have already passed the Certification test :-)
--- In Crestron@..., "lincster2010" <lincster2010@> wrote:
IIRC, at Masters, Mr. O said people could get a copy of the old test, because the new test would be different.
--- In Crestron@..., "eagrubbs" <eagrubbs@> wrote:
I hope the test is different because that would be complete BS if it was the same test. A guy I work with that has not been to the 3rd class called crestron and was offered a copy of the test and got it. It was the same test I had. WTF? You mean you are giving out the test to anyone now without the time constraints the rest of us had. That really doesn't sound fair.
--- In Crestron@..., "doug_h_encinitas" <dghardy@> wrote:
I just finished 301 last week and on Friday the sent out an email saying they were changing the cert test. I got mine in an email yesterday. And looks and sounds like the old cert test. Even one of the questions I remember someone telling me last week about needing to use a 8 or 12 digit keypad with .wav playback function and sure enough it was this cert. if u want I can shoot u a copy of the scope, I don't think it will hurt to see what ur getting into.
--- In Crestron@..., "Mark" <dedicatedsystems@> wrote:
I am in my C301 class this week.
Seems they are changing the test process? Anyone know the details?
Apparently a email went out this morning to crestron employees that they are changing the test.....
Anyone know?
|
Re: TSW panels Gesture Canvas over buttons
Not currently. I made a request in labs about this some time ago I think.
I was hoping to use a gesture canvas to scroll "pages" on an icon list.
Maybe search on labs and add a request.
toggle quoted message
Show quoted text
On Mon, Apr 29, 2013 at 8:41 AM, Seth Olle <seth@...> wrote: **
Working on a TSW panel.
Can you put a gesture canvas over buttons?
Basically push through the gesture canvas to select buttons below it.
I am working on something where I will need the gesture up and down,
however I need buttons below to actually select items.
Is this possible? Hopefully I am just missing something?
Seth
|
TSW panels Gesture Canvas over buttons
Working on a TSW panel.
Can you put a gesture canvas over buttons?
Basically push through the gesture canvas to select buttons below it.
I am working on something where I will need the gesture up and down, however I need buttons below to actually select items.
Is this possible? Hopefully I am just missing something?
Seth
|
Re: Certification Changes
This is what I figured would happen. :|
toggle quoted message
Show quoted text
--- In Crestron@..., allen mcdaniel <amac2673@...> wrote:
I just took the Cert class and the test is the same as its always been.
To: Crestron@...
From: lincster2010@...
Date: Mon, 29 Apr 2013 12:53:54 +0000
Subject: [Crestron] Re: Certification Changes
IIRC, at Masters, Mr. O said people could get a copy of the old test, because the new test would be different.
--- In Crestron@..., "eagrubbs" <eagrubbs@> wrote:
I hope the test is different because that would be complete BS if it was the same test. A guy I work with that has not been to the 3rd class called crestron and was offered a copy of the test and got it. It was the same test I had. WTF? You mean you are giving out the test to anyone now without the time constraints the rest of us had. That really doesn't sound fair. --- In Crestron@..., "doug_h_encinitas" <dghardy@> wrote:
I just finished 301 last week and on Friday the sent out an email saying they were changing the cert test. I got mine in an email yesterday. And looks and sounds like the old cert test. Even one of the questions I remember someone telling me last week about needing to use a 8 or 12 digit keypad with .wav playback function and sure enough it was this cert. if u want I can shoot u a copy of the scope, I don't think it will hurt to see what ur getting into.
--- In Crestron@..., "Mark" <dedicatedsystems@> wrote:
I am in my C301 class this week.
Seems they are changing the test process? Anyone know the details?
Apparently a email went out this morning to crestron employees that they are changing the test.....
Anyone know?
[Non-text portions of this message have been removed]
|
Re: Certification Changes
I thought he was referring to the Gold test - which would make sense, since everyone at Masters would have already passed the Certification test :-)
toggle quoted message
Show quoted text
--- In Crestron@..., "lincster2010" <lincster2010@...> wrote:
IIRC, at Masters, Mr. O said people could get a copy of the old test, because the new test would be different.
--- In Crestron@..., "eagrubbs" <eagrubbs@> wrote:
I hope the test is different because that would be complete BS if it was the same test. A guy I work with that has not been to the 3rd class called crestron and was offered a copy of the test and got it. It was the same test I had. WTF? You mean you are giving out the test to anyone now without the time constraints the rest of us had. That really doesn't sound fair.
--- In Crestron@..., "doug_h_encinitas" <dghardy@> wrote:
I just finished 301 last week and on Friday the sent out an email saying they were changing the cert test. I got mine in an email yesterday. And looks and sounds like the old cert test. Even one of the questions I remember someone telling me last week about needing to use a 8 or 12 digit keypad with .wav playback function and sure enough it was this cert. if u want I can shoot u a copy of the scope, I don't think it will hurt to see what ur getting into.
--- In Crestron@..., "Mark" <dedicatedsystems@> wrote:
I am in my C301 class this week.
Seems they are changing the test process? Anyone know the details?
Apparently a email went out this morning to crestron employees that they are changing the test.....
Anyone know?
|
Re: Internet Radio - Control Via Touchpanels
Cen-track with an Internet radio card. Fusion Research - OMS-1 with a
squeezebox driver. Or even a squeezebox if you can find one. I'm sure there
are more ways, those are the ones I've used successfully.
Nick
Sent from my eMail.
toggle quoted message
Show quoted text
On Apr 29, 2013, at 7:36 AM, tomasogmor <tomasog@...> wrote:
Hi,
Am looking to find a solution to get Internet Radio (for multi-room audio)
controlled from the room touchpanels.
At Present we are using Rasberry Pi's running XBMC as the sources for the
Crestron Multi-Room amps (2 x C2N-AMP-4x100) the Touchpanels range from
TPS-4L's to TPMC-8X and a TSW-750. Running with a MC2E Processor.
I have the Crestron XBMC Module Running and it's fine for browsing MP3's
etc. in the Library. But I cannot get the touchanels to control any of the
Radio add-ons.
Is there any other way anyone can think of doing this, without have to
purchase an Adagio system or something.
It doesn't have to be XBMC, I just want the user to be able to pick On-Line
radio stations from the ouchpanel.
Thanks a mil,
Tomas
[Non-text portions of this message have been removed]
|
Re: Certification Changes
I just took the Cert class and the test is the same as its always been. To: Crestron@... From: lincster2010@... Date: Mon, 29 Apr 2013 12:53:54 +0000 Subject: [Crestron] Re: Certification Changes IIRC, at Masters, Mr. O said people could get a copy of the old test, because the new test would be different. --- In Crestron@..., "eagrubbs" <eagrubbs@...> wrote: I hope the test is different because that would be complete BS if it was the same test. A guy I work with that has not been to the 3rd class called crestron and was offered a copy of the test and got it. It was the same test I had. WTF? You mean you are giving out the test to anyone now without the time constraints the rest of us had. That really doesn't sound fair. --- In Crestron@..., "doug_h_encinitas" <dghardy@> wrote:
I just finished 301 last week and on Friday the sent out an email saying they were changing the cert test. I got mine in an email yesterday. And looks and sounds like the old cert test. Even one of the questions I remember someone telling me last week about needing to use a 8 or 12 digit keypad with .wav playback function and sure enough it was this cert. if u want I can shoot u a copy of the scope, I don't think it will hurt to see what ur getting into.
--- In Crestron@..., "Mark" <dedicatedsystems@> wrote:
I am in my C301 class this week.
Seems they are changing the test process? Anyone know the details?
Apparently a email went out this morning to crestron employees that they are changing the test.....
Anyone know?
[Non-text portions of this message have been removed]
|
I also have a Pakedge sw8-4pb On Apr 29, 2013 7:19 AM, "m.nguyen" <mpninc@...> wrote: I have the exact same problem and it is very random. I also have gone
thru all the Crestron channels and they have found nothing. I have told my
customer that if the panel lock up pull it from the wall and unplug the
cable and plug back.
On Apr 29, 2013 7:13 AM, "jason santlofer" <jason@...> wrote:
**
Heath,
What kind of switches are you using Or have you tried?
Jason
Sent from my Verizon Wireless 4G LTE DROID
Heath Volmer <hvolmer@...> wrote:
I suspect that you'll find that they are still on line, and transmitting presses, but have stopped responding to feedback. If not, you've got a
different problem than what many of us have been up against. I've been
dealing with this for a while and the band-aid solution for now is to use
the PERIODICREBOOT ON command to keep the things fresh every day. If
someone needs multiple reboots per day, you may need to devise logic to
console and issue reboot commands multiple times.
We've been through the "channels", all the way. No more channels to go
through. They know that something is wrong. I had almost lost faith in my
own ability to finish ;-).
Heath
On Apr 29, 2013, at 6:34 AM, jmgaudiovideo <jason@...> wrote:
Hi All,
Not not sure if this has been touched upon somewhere along the lines.
I'm sure everyone has their stories about the new TSW-750 panels. I need
some help. We have a couple of these systems in the field and both of them
seem to have problems with the touchscreens just randomly freezing and
falling off line. We have updated to just about every firmware Crestron has
put out even some of the beta ones. We don't even have video running to the
panels so I don't think it a memory issue. The only common denominator in
the two systems is a Pakedge SW16-16PB ethernet switch which is powering
the panels. It is a managed switch. On the larger job (10 tsw panels)the
switch would actually freeze and need to be rebooted along with the CP3
processor to make them work again. On the other job the client says he just
needs to reboot the panel to make them work. But he does so a couple times
a day. We have gone through the channels at Crestron sent in code etc and
they can't pinpoint a problem. I and our programmer have been working with
Crestron product for quite a few years and never experienced these kind of
problems before. Is anyone else experiencing these types of issues and if
so were you able to solve them? My customers are increasingly losing faith
in our ability to finish the job and honestly I am at a loss.
[Non-text portions of this message have been removed]
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the
Database area.
Yahoo! Groups Links
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
|
I have the exact same problem and it is very random. I also have gone thru
all the Crestron channels and they have found nothing. I have told my
customer that if the panel lock up pull it from the wall and unplug the
cable and plug back.
toggle quoted message
Show quoted text
On Apr 29, 2013 7:13 AM, "jason santlofer" <jason@...> wrote: **
Heath,
What kind of switches are you using Or have you tried?
Jason
Sent from my Verizon Wireless 4G LTE DROID
Heath Volmer <hvolmer@...> wrote:
I suspect that you'll find that they are still on line, and transmitting presses, but have stopped responding to feedback. If not, you've got a
different problem than what many of us have been up against. I've been
dealing with this for a while and the band-aid solution for now is to use
the PERIODICREBOOT ON command to keep the things fresh every day. If
someone needs multiple reboots per day, you may need to devise logic to
console and issue reboot commands multiple times.
We've been through the "channels", all the way. No more channels to go
through. They know that something is wrong. I had almost lost faith in my
own ability to finish ;-).
Heath
On Apr 29, 2013, at 6:34 AM, jmgaudiovideo <jason@...> wrote:
Hi All,
Not not sure if this has been touched upon somewhere along the lines.
I'm sure everyone has their stories about the new TSW-750 panels. I need
some help. We have a couple of these systems in the field and both of them
seem to have problems with the touchscreens just randomly freezing and
falling off line. We have updated to just about every firmware Crestron has
put out even some of the beta ones. We don't even have video running to the
panels so I don't think it a memory issue. The only common denominator in
the two systems is a Pakedge SW16-16PB ethernet switch which is powering
the panels. It is a managed switch. On the larger job (10 tsw panels)the
switch would actually freeze and need to be rebooted along with the CP3
processor to make them work again. On the other job the client says he just
needs to reboot the panel to make them work. But he does so a couple times
a day. We have gone through the channels at Crestron sent in code etc and
they can't pinpoint a problem. I and our programmer have been working with
Crestron product for quite a few years and never experienced these kind of
problems before. Is anyone else experiencing these types of issues and if
so were you able to solve them? My customers are increasingly losing faith
in our ability to finish the job and honestly I am at a loss.
[Non-text portions of this message have been removed]
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the
Database area.
Yahoo! Groups Links
|
Heath,
What kind of switches are you using Or have you tried?
Jason
Sent from my Verizon Wireless 4G LTE DROID
Heath Volmer <hvolmer@...> wrote:
toggle quoted message
Show quoted text
I suspect that you'll find that they are still on line, and transmitting presses, but have stopped responding to feedback. If not, you've got a different problem than what many of us have been up against. I've been dealing with this for a while and the band-aid solution for now is to use the PERIODICREBOOT ON command to keep the things fresh every day. If someone needs multiple reboots per day, you may need to devise logic to console and issue reboot commands multiple times.
We've been through the "channels", all the way. No more channels to go through. They know that something is wrong. I had almost lost faith in my own ability to finish ;-).
Heath
On Apr 29, 2013, at 6:34 AM, jmgaudiovideo <jason@...> wrote:
Hi All,
Not not sure if this has been touched upon somewhere along the lines. I'm sure everyone has their stories about the new TSW-750 panels. I need some help. We have a couple of these systems in the field and both of them seem to have problems with the touchscreens just randomly freezing and falling off line. We have updated to just about every firmware Crestron has put out even some of the beta ones. We don't even have video running to the panels so I don't think it a memory issue. The only common denominator in the two systems is a Pakedge SW16-16PB ethernet switch which is powering the panels. It is a managed switch. On the larger job (10 tsw panels)the switch would actually freeze and need to be rebooted along with the CP3 processor to make them work again. On the other job the client says he just needs to reboot the panel to make them work. But he does so a couple times a day. We have gone through the channels at Crestron sent in code etc and they can't pinpoint a problem. I and our programmer have been working with Crestron product for quite a few years and never experienced these kind of problems before. Is anyone else experiencing these types of issues and if so were you able to solve them? My customers are increasingly losing faith in our ability to finish the job and honestly I am at a loss.
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links
|
I suspect that you'll find that they are still on line, and transmitting presses, but have stopped responding to feedback. If not, you've got a different problem than what many of us have been up against. I've been dealing with this for a while and the band-aid solution for now is to use the PERIODICREBOOT ON command to keep the things fresh every day. If someone needs multiple reboots per day, you may need to devise logic to console and issue reboot commands multiple times. We've been through the "channels", all the way. No more channels to go through. They know that something is wrong. I had almost lost faith in my own ability to finish ;-). Heath On Apr 29, 2013, at 6:34 AM, jmgaudiovideo <jason@...> wrote: Hi All,
Not not sure if this has been touched upon somewhere along the lines. I'm sure everyone has their stories about the new TSW-750 panels. I need some help. We have a couple of these systems in the field and both of them seem to have problems with the touchscreens just randomly freezing and falling off line. We have updated to just about every firmware Crestron has put out even some of the beta ones. We don't even have video running to the panels so I don't think it a memory issue. The only common denominator in the two systems is a Pakedge SW16-16PB ethernet switch which is powering the panels. It is a managed switch. On the larger job (10 tsw panels)the switch would actually freeze and need to be rebooted along with the CP3 processor to make them work again. On the other job the client says he just needs to reboot the panel to make them work. But he does so a couple times a day. We have gone through the channels at Crestron sent in code etc and they can't pinpoint a problem. I and our programmer have been working with Crestron product for quite a few years and never experienced these kind of problems before. Is anyone else experiencing these types of issues and if so were you able to solve them? My customers are increasingly losing faith in our ability to finish the job and honestly I am at a loss.
[Non-text portions of this message have been removed]
|
That is for the fusion research, been there done that.
Interest in the grace digital product.
From: texascbounds <clbounds@...<mailto:clbounds@...>>
Reply-To: "Crestron@...<mailto:Crestron@...>" <Crestron@...<mailto:Crestron@...>>
Date: Monday, April 29, 2013 9:29 AM
To: "Crestron@...<mailto:Crestron@...>" <Crestron@...<mailto:Crestron@...>>
Subject: [Crestron] Re: Grace Internet Tuner
Yes check out
toggle quoted message
Show quoted text
--- In Crestron@...<mailto:Crestron%40yahoogroups.com>, Seth Olle <seth@...> wrote:
Saw mention of this.
Has anyone controlled this effectively as a low cost replacement for a squeezebox?
,
|
Yes check out
toggle quoted message
Show quoted text
--- In Crestron@..., Seth Olle <seth@...> wrote:
Saw mention of this.
Has anyone controlled this effectively as a low cost replacement for a squeezebox?
,
|
Re: Wireless battery powered wall mounted keypad?
I would be interested in the module for this keypad.
It seems like an interesting solution.
Post it if possible.
From: Block-O-Matic <michael@...<mailto:michael@...>>
Reply-To: "Crestron@...<mailto:Crestron@...>" <Crestron@...<mailto:Crestron@...>>
Date: Sunday, April 28, 2013 1:12 PM
To: "Crestron@...<mailto:Crestron@...>" <Crestron@...<mailto:Crestron@...>>
Subject: [Crestron] Re: Wireless battery powered wall mounted keypad?
www.adhocelectronics.com for EnOcean products. Check out the wireless light switches. They don't need batteries ever- electricity is generated by the button press and release. I have several of them at home and they work great. There are several receivers to choose from including relay outputs and rs232. I have a module I can post if you need it.
You can find some more selection on amazon. Leviton is oem'ing the product and have some other products that are interesting. Anything EnOcean is compatible.
Mb
toggle quoted message
Show quoted text
--- In Crestron@...<mailto:Crestron%40yahoogroups.com>, "Mark" <access@...> wrote:
I've got a system with 4 zones of garden lighting which are controlled via Crestron primarily on Mobile & Mobile Pro G.
However, we need to fit a wall station of some description in a location where cabling is impossible to control them as well.
Something like a cameo keypad would be ideal, but they all need cabling of one sort or another (I know there's a battery powered infinet keypad on the cards, but it's not been released yet to my knowledge)
There is a Pro2 nearby, so I'm thinking of a battery powered wireless solution somehow connected to the versiport inputs of the Pro2 and go programatically from there.
Has anyone got any idea of any elegant hardware I could use?
Cheers.
Mark
|
Michael Block