¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date
New Processor FW v1.603.0113
Has anyone seen any issues with this FW from last week?? Obviously it's supposed to fix the Sonos S1 Comm's/#Favs issue, but wanted to see if there were any unexpected problems... I have a couple
By ckangis · #237930 ·
Re: XPanel port 42872 workaround
Not fully tested I see. Yes it kinda works if you run it from VTP with F11. Does not work if you double click the vtz. Still defaults to?42872. In my mind the default behaviour should be to default
By Slip Cougan · #237929 ·
Re: Lexicon MC-10
A bit of off topic but why doesn't anymone make a pre/pro in 2U may be even 1U size?
By ZS · #237928 ·
Re: XPanel port 42872 workaround
*https://www.crestron.com/Software-Firmware/Software/VisionTools-153;-Pro-e/VT-Pro-e-6/6-2-01-31* -------------------------------------------------------------------------------------------------
By Dave H - Crestron True Blue Tech Support Engineer Since 2014 · #237927 ·
Re: Lexicon MC-10
Here is a link to the Protocol Document. I am creating my own module since the MC-8 is a complete different set of commands. So far, I am finding all the commands in the doc to be good.
By Michael Benignus · #237926 ·
Re: Processor not recognising unchanged IP table.
I'm sure that the shade power supply/hub has the same issue as the other hubs. It totally makes sense. Eventually, Crestron will fix it, but not until they can find something else to break.
By Brian Matson · #237925 ·
Re: Crestron RMC3 with Cisco Touch 10 and Codec Pro
No, not needed for the RMC3 to connect. Just need SSH turned on and configured properly in your module. You can also try changing the SSH connection type to "Unsecure" in the Parameters if you simply
By Chris · #237924 ·
Re: Processor not recognising unchanged IP table.
Remote System Definition
By Brian Matson · #237923 ·
Re: Processor not recognising unchanged IP table.
I don't have either a DIN-CEN-CN-2 nor the CAEN-BLOCK-CENCN-2-POE in my program. I do however have a?CSA-PWS10S-HUB-ENET, and it very possibly that I only saw this pop up on this project after I
By rickwookie · #237922 ·
Re: Processor not recognising unchanged IP table.
RSD?
By rickwookie · #237921 ·
Re: Processor not recognising unchanged IP table.
I've noticed the same thing with regards to the CAEN-BLOCK-CENCN-2-POE. I was told that there is a known issue with the later versions of Toolbox and these devices. IP ID conversion makes sense
By Brian Matson · #237920 ·
Re: VTPro issues
Why haven't all of you moved to using CH5 now??? Oh wait...that's right!...it still doesn't work...:):):)
By ckangis · #237919 ·
Re: system upgrade suggestions
NP! Feel free to ping me if you want to chat about any of the items... chris at eicustom dot com
By ckangis · #237918 ·
Re: Processor not recognising unchanged IP table.
It does this every time when you have a DIN-CEN-CN-2 in your program. I mentioned it offhand to someone at Crestron and they said it's probably because there is some IP ID conversion that's happening
By Hope Roth · #237917 ·
Re: VTPro issues
Supposed to... but it still does anyway.
By Jeremy Weatherford · #237916 ·
Re: VTPro issues
I believe if you disable snapping, the quick assign won't move them.
By Rob · #237915 ·
Re: Processor not recognising unchanged IP table.
Are you working with RSDs in your Simpl program? Sometimes that trips me up because in the stupidity of replacing a RSD on an existing IPID, Simpl doesnt keep the IP address when you replace it, it
By @johnmax · #237914 ·
Re: Processor not recognising unchanged IP table.
" It is de rigeur if you¡¯re remapping IP table entries (in my experience at least)¡­I¡¯ve never thought t bothersome enough to worry about though" Me neither, it's a useful notification in that
By rickwookie · #237913 ·
Re: Processor not recognising unchanged IP table.
It is de rigeur if you¡¯re remapping IP table entries (in my experience at least)¡­I¡¯ve never thought t bothersome enough to worry about though, nor can I remember it occurring when I¡¯m not
By Lincoln King-Cliby · #237912 ·
Processor not recognising unchanged IP table.
Has anyone else had a processor get stuck where this message is presented every time you upload, even though nothing in the IP table has changed? I had it once before on a CP3, and in the end I did a
By rickwookie · #237911 ·