¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Crestron
  2. Messages
Expanded Topics Messages Polls
Date
Re: CP4 -> D3 Program (on same CP4) -> CEN-GWEX-ER: No communication with CLW-SWDIMEX-P's

 

Tray, the MC3 does not support the authentication needed for a gwexer. You will need to take the firmware back in the gwexer
Re: CP4 -> D3 Program (on same CP4) -> CEN-GWEX-ER: No communication with CLW-SWDIMEX-P's

 

As Mentioned check for CSAuthen on both ends and you may need to run the unlock / unblock User and IP after setting those. Do not rely on Authen info in tool box just run the command have found that on serveral occasions when nothing showed as blocked or locked out but was..
Re: Can't connect to a PRO3 from toolbox

 

Try connecting with tool box Secondary Console. Or USB if those don't work and you cant find it with wire shark or angy IP only choice I see is try a factory restore.
Can't connect to a PRO3 from toolbox

 

I bought 2 PRO3's.? One for the main house for a upgrade from a 2 series.? That one was wiped and had no problems connecting.? The second one still has a project on it.
Front panel shows that it has a static address of 192.168.10.2.? I have tried connecting with that and it's host name.? Also device discovery tool doesn't see it.? I tried a 3rd party IP scanner that doesn't see it.? Any thoughts???
Re: CEN-IO-xx-104 and 4-series

 

¿ªÔÆÌåÓý

Seems like rolling back firmware to a pre-Auth version might be the answer.

I was just stating that I did what you did and it worked on series 4?

I know, not much help

On Apr 10, 2024, at 1:41?PM, Tray Schaeffer <trayschaeffer@...> wrote:

?This does not work for CEN-GWEXER. Trying to find a solution

Re: CEN-IO-xx-104 and 4-series

 

This does not work for CEN-GWEXER. Trying to find a solution
Re: CP4 -> D3 Program (on same CP4) -> CEN-GWEX-ER: No communication with CLW-SWDIMEX-P's

 

¿ªÔÆÌåÓý

I had same issue with a 4 series. Turned out mine was authentication.

Just as you describe, I set device username and password, then it worked.

Haven¡¯t used a Genwexer since¡­..


On Apr 10, 2024, at 1:17?PM, Tray Schaeffer <trayschaeffer@...> wrote:

?Can't get CEN-GWEX-ER to connect to MC3 control system.?
setup the user as described and it will not connect at all.?
Any ideas apart from rolling back the gateway firmware?

Re: CP4 -> D3 Program (on same CP4) -> CEN-GWEX-ER: No communication with CLW-SWDIMEX-P's

 

Can't get CEN-GWEX-ER to connect to MC3 control system.?
setup the user as described and it will not connect at all.?
Any ideas apart from rolling back the gateway firmware?
Re: Cannot get DMPS3-4K-350-C H.264 input to work

 

From looking at the streaming specifications.? The DMPS only supports RTP, RTSP, and SDP streams. Both H.264 and MJPEG are supported.??


On Wed, Apr 10, 2024, 1:05?PM <dwiencek@...> wrote:

[Edited Message Follows]

Any advice on getting a stream on the DMPS3 would be greatly appreciated. I set up a stream with a pull link from Restream (rtmp://), but could not get the DMPS3 to accept it, no matter what settings were changed. However, VLC had no problem with the stream. I'd really like to get this option functioning as part of a video system upgrade in one of our larger theatres. Thanks in advance!

Dan

Edit: I brought everything to my home network and was unsuccessful, eliminating a firewall issue or something else on our network.
Cannot get DMPS3-4K-350-C H.264 input to work

 
Edited

Any advice on getting a stream on the DMPS3 would be greatly appreciated. I set up a stream with a pull link from Restream (rtmp://live.restream.io/pull/play_3132352_366e659ded2fd19a260d), but could not get the DMPS3 to accept it, no matter what settings were changed. However, VLC had no problem with the stream. I'd really like to get this option functioning as part of a video system upgrade in one of our larger theatres. Thanks in advance!

Dan

Edit: I brought everything to my home network and was unsuccessful, eliminating a firewall issue or something else on our network.
Somfy 485 termination

 

Hello,

We have a Crestron Com-3 talking to a series for Somfy SDB networked shades.? When the shades installer hooked up their PC the shades worked flawlessly, but we can't get consistent reliable control.? The PDF for the Crestron module mentions a 120 ohm termination resistor at both ends of the network.? Do we need to add this to the Crestron end or does its 485 already have this type of termination?
Sirius XM tuner for terrestrial signal?

 

I have a client whose old Polk Audio SR-H2000 finally died.? He had the "lifetime" subscription tied to it so tears were shed.? Is there a rack mount tuner with 232 that is currently available?? I'm ready to jump on ebay and look for an C2NTXM if I have too, but streaming is not desired.? He has an MMS, and hates using it for reasons.
Re: Audio Only source via DM

 

Hey CO Cowboy,

I dont see that option on any of my outputs.
Is that only available on a specific RMC?

I am only looking in DM Tools.
Re: Lutron Smart Bridge Pro Caseta switches and Crestron Home

 

The Serena shades are locked to the Caseta platform.
Re: Audio Only source via DM

 

Matt,
On the output settings of the endpoint,? there is a selection to play audio without video, but this requires you load a graphics file (we use our company logo). We haven't had any "select video first" issues since we started doing that.
Connection to DM-NVX-D200 with DMNVX tool or device discovery

 

Hello,
Thought I would post this here as well as TB
I have a DM-NVX D200 and E30 that I am setting up. I plug them both into a network switch at my desk to configure them and update firmware. I have my laptop connected to the same switch. When I run DM NVX tool ( or device discovery) I can only see the E30 listed as devices that are plugged in.
If I connect my laptop directly to the D200 it shows in the DM NVX tool (and device discovery), I can connect to it and upload firmware.
Question is why can't I see both the D200 and E30 in the DM NVX tool when all three devices (D200, E30 and laptop) are connected to the same switch.

Thanks
Re: Lutron Smart Bridge Pro Caseta switches and Crestron Home

 

I thought all shades were clear connect and would work across all current processors
Re: USB Console connection DM-NVX-360

 

If you mess up the network config badly enough that doesn't work - for example putting 0.0.0.0 as the subnet mask.? :)


On Tue, Apr 9, 2024 at 11:55?PM Steve Kuehn <steve@...> wrote:
While I haven't tried it, is there an reason why you couldn't ssh into the DM-NVX-360 and get to the text console that way?? I found most Crestron products except for newer version of the CP4R will accept and SSH connection.

Re: USB Console connection DM-NVX-360

 

While I haven't tried it, is there an reason why you couldn't ssh into the DM-NVX-360 and get to the text console that way?? I found most Crestron products except for newer version of the CP4R will accept and SSH connection.
Re: USB Console connection DM-NVX-360

 

Hello,

Is this possible?

Thank you
Bryan
3621 - 3640 of 256471