¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Crestron
  2. Messages
Expanded Topics Messages Polls
Date
Re: 552 Panels

 

I have 2 units a 552 and a 752 exhibiting the same behavior. The project is three hours away and I would like to have a permanent fix before I head there tomorrow. TB told me to reload the .puf and .vtz files, did not work but I was doing it remotely and could not see exactly what was going on.


-Paul
Has anyone seen any issues with yesterday's Mobile Pro G update?

 

I have received 3 phone calls so far. All jobs were fine before the update.
Re: Duplicate Extenders when Refresh Smart Graphics

 

¿ªÔÆÌåÓý

I have TSW-1052, TSW-752, Xpanel, iPad and iPhone. All are a direct save as from the 1052. (Eventually I will make a dedicated iPhone version) It doesn't seem to matter if I keep the extenders connected to the original or not, but I've been mostly working with the assumption that I want them disconnected from each other.?

-Kevin Keenan

On Sep 3, 2014, at 5:06, "Andrew Welker andrew.welker@... [Crestron]" <Crestron@...> wrote:

?

How may different panel files are you using? Are any of them derived from each other?

On Sep 2, 2014 11:53 PM, "kevinfkeenan@... [Crestron]" <Crestron@...> wrote:
?

I am not saving as a new name. ?Just saving and compiling the panel, then refreshing in Simpl.
Re: Duplicate Extenders when Refresh Smart Graphics

Andrew Welker
 

How may different panel files are you using? Are any of them derived from each other?

On Sep 2, 2014 11:53 PM, "kevinfkeenan@... [Crestron]" <Crestron@...> wrote:

?

I am not saving as a new name. ?Just saving and compiling the panel, then refreshing in Simpl.
Re: 552 Panels

 

I just got a message from a client who has 3) 1052s that are experiencing the same symptoms. ?He rebooted the POE, and the problem doesn't go away. Two of them are stuck loading, the other says no project loaded.

Of course, these are the only devices I don't have set up in the router, and I am 6500 miles away in Warsaw.
Re: 552 Panels

 

A complete shot in the dark, but one thing I'd check is the power status on the panels.


There's some information in the boot log (err plogcurrent) which can indicate an under voltage.? Obviously, we know thins from experience of a PoE switch that wasn't able to deliver sufficient power to the panels and the result was that they would freeze up.? Removing load from the switch resolved the issue.


This is what we were seeing in the log:

Persistent log contents during current boot:
HW WDOG: PMIC FAULT_LOG Register Content:
Watchdog Time Violated = 0
VDDOUT under voltage power down = 1

...


A pain - but at least it's an easy one to resolve if that's the issue.


Cheers,

Ol
Re: Duplicate Extenders when Refresh Smart Graphics

 

I am not saving as a new name. ?Just saving and compiling the panel, then refreshing in Simpl.
Re: DMPS-100-C no Source Audio control

Andrew Welker
 

What happens if you turn the knob on the front of the unit?

On Sep 2, 2014 8:28 PM, "jahonix@... [Crestron]" <Crestron@...> wrote:

?

I'm sitting in a project and going nuts with a DMPS-100-C.

I cannot control the analog output volume of the selected video source, no matter which one I choose.
Neither by programming nor with the DMPS Tools. I can move the faders on the "Analog Output Configuration" page and see feedback from the unit changing values.
But sound stays at the same (max!) level.
Feedback signal is:
?DMPC-100-C_Slot8_Slot7_Source_Set_Left_to_Out_Left_F
Values range from -800d to 0d as expected. (same for right channel)
Input trim -10dB to +10dB works, however.

Anyone experienced this before?

This is a University project where we install two identical systems.
The first DMPS-100-C stuck in boot loop with no chance to recover and was replaced with a DMPS-300-C.
Nearly identical programming on that unit works as expected.

Your ideas are greatly appreciated!

Cheers
Chris
Re: Importing Smart Graphics/Objects into Simple

 

Anytime that I 'refresh smart graphics extenders', Simpl comments out all of the old extenders and imports all brand new versions WITHOUT my programming. ?Am I doing something wrong or is this a 'feature'? ?I have 18 panels and about 20 SG extenders and even with the new duplicate programming, it is tiresome to delete all the commented out extenders after copying.... oy!
Re: 552 Panels

 

¿ªÔÆÌåÓý

I have a couple very early 552s in my house and haven¡¯t encountered anything like the described. The OS should not be background updating at all.

?

--

Lincoln King-Cliby, CTS, DMC-E-4K/T/D

Commercial Market Director

Sr. Systems Architect | Crestron Certified Master Programmer (Gold)

Crestron Services Provider | Biamp Audia Certified | Extron Control Professional

From: Crestron@... [mailto:Crestron@...]
Sent: Tuesday, September 02, 2014 8:46 PM
To: Crestron@...
Subject: [Crestron] 552 Panels

?




Just wondering if anyone has had this issue before... So I installed several TSW-1052's and TSW-552's last week. ?Updated all the firmware to these panels to the latest firmware, loaded my graphics tested and went home. ?That was last Thursday. ?I go to the job site today and every single touch panel was now locked up. I have 5 1052's and about 8 552;s on site. ?A few V15's as well but all those are OK.

?

?Some were stuck in the Crestron Loading screen, some were stuck on a black screen, and one was stuck with a message saying the Android OS was being updated. ?But it all cases, I was able to connect to the panels via toolbox. ?I was not able to reload any project to ANY of them. ?All gave me an error message when uploading through FTP or through Toolbox. ?Of course I caught this towards the end of the day so Crestron tech support wasnt able to do much yet (I will be back with them tomorrow after to double check code and VTProe files).

?

What I was thinking is that maybe the Andoind OS operating system started to get updated in the background and jammed the panels up. ?Anyone else seend or heard anything like this?? ?I'll update when I go back on site tomorrow and call back tech support.

?
Re: DMPS-300-C Volume Analog Values

 

The whole DMPS-100-C package programming is available from the download section of the crestron site.
This can serve you as a reference.

DMPS-100-C
DMPS Autoconfiguration Software Bundle
Example Program (ZIP - 51.1 M)
Rev. Date: 05/19/14
Description:
The DMPS Autoconfiguration software comes preloaded on DMPS-100-Cs bought after March 17th 2014 and with the TSW-750-DMPS-AM-B-S. The software provided in this package can be loaded to existing DMPS-100-Cs and TSW-750s. It provides a simple configuration and switching interface for the DMPS-100-C. In addition, it offer control of displays from several manufacturers
Version Number: 1.1
552 Panels

 

Just wondering if anyone has had this issue before... So I installed several TSW-1052's and TSW-552's last week. ?Updated all the firmware to these panels to the latest firmware, loaded my graphics tested and went home. ?That was last Thursday. ?I go to the job site today and every single touch panel was now locked up. I have 5 1052's and about 8 552;s on site. ?A few V15's as well but all those are OK.


?Some were stuck in the Crestron Loading screen, some were stuck on a black screen, and one was stuck with a message saying the Android OS was being updated. ?But it all cases, I was able to connect to the panels via toolbox. ?I was not able to reload any project to ANY of them. ?All gave me an error message when uploading through FTP or through Toolbox. ?Of course I caught this towards the end of the day so Crestron tech support wasnt able to do much yet (I will be back with them tomorrow after to double check code and VTProe files).


What I was thinking is that maybe the Andoind OS operating system started to get updated in the background and jammed the panels up. ?Anyone else seend or heard anything like this?? ?I'll update when I go back on site tomorrow and call back tech support.
DMPS-100-C no Source Audio control

 

I'm sitting in a project and going nuts with a DMPS-100-C.

I cannot control the analog output volume of the selected video source, no matter which one I choose.
Neither by programming nor with the DMPS Tools. I can move the faders on the "Analog Output Configuration" page and see feedback from the unit changing values.
But sound stays at the same (max!) level.
Feedback signal is:
?DMPC-100-C_Slot8_Slot7_Source_Set_Left_to_Out_Left_F
Values range from -800d to 0d as expected. (same for right channel)
Input trim -10dB to +10dB works, however.

Anyone experienced this before?

This is a University project where we install two identical systems.
The first DMPS-100-C stuck in boot loop with no chance to recover and was replaced with a DMPS-300-C.
Nearly identical programming on that unit works as expected.

Your ideas are greatly appreciated!

Cheers
Chris
DMPS-300-C Volume Analog Values

 

Anyone have good settings to use with the analog values of DMPS volumes? Some of the signals have ranges from -800d to 0d and others are 0d to 65535d. I'm trying to drive them with Analog Increments... but strange things are happening. Then there's the Gauge Settings on a Smart Graphics panel, where I set the min and max values for the gauge.?


Thanks.


Better yet, does a huge demo program exist that shows how to properly use the giant DMPS module?
Re: Crestron App Crash

 

I just went through the same issue showing up on my testing iPad that had worked without fail previously. I also successfully loaded the same file to the clients iPad Air running same app version and iOS version.

Ran the usual routine, rebooted everything, reloaded, nuked Dropbox, etc. to no success.

Fix for me was deleting the Crestron App on the iPad, re-installing it and re-entering the settings in the app.

Everything is working fine now.

Gremlins...
How do i use a state join on a button with D3Pro

[email protected]
 

Hi All,

I'm trying to use a state join on a button with D3pro. I just can't find the place to ling the analog join to a fb value?


Please help!!


TV
Re: OT: AV Rental in Irving TX

 

Thanks Andrew, I will check them out.
din-io8 programming in crestron studio

 

hi,

any ideas on how to program din-io8 in crestron studio ?

thanks a lot
Re: Silly question - SG Legend equiv

 

¿ªÔÆÌåÓý

Duh. Lol


On Sep 2, 2014, at 1:19 PM, "Davis Whitehurst whitehurstd@... [Crestron]" <Crestron@...> wrote:

?

Why not just use buttons with visibility joins?
Exactly the same as a legend

Davis

________________________________

CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.
Re: Silly question - SG Legend equiv

 

Why not just use buttons with visibility joins?
Exactly the same as a legend

Davis

________________________________

CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.
58641 - 58660 of 256472