I was wrong.? The handheld remote has the same issue.? Any Somfy experts out there?

I have one of these connected to a CP3 - all well for 8 months or so.? Now, driving one shade will affect another but not vis-versa.? Have reset the shade addresses and confirmed them unique.? (Shade address 8 controls shades 8 and 6 .? Shade address 6 only controls 6).

Removed the URTSI II from the Crestron (using it stand alone) and the problem remains.? The hand held Somfy remotes work just fine.

Is there a way to "reset" the URTSI II?? Anyone else seen this?? I'm on site and can't get a phone number for Somfy.? I have a request in to their support for? a call back.

If the iOS device is up to date you should get a back to Crestron button at the top left of the screen if the app is opened from within Crestron app. This is built into iOS so unless Zoom or Teams is overriding it somehow it doesn't take anything from you to make it happen.

So I know you can launch apps from Crestron's iPad UI, like Zoom and Teams, etc. but can you go the other way? (go back to the Crestron's UI from Zoom or Teams)

Thank you,

The following files have been uploaded to the Files area of the [email protected] group.

• /Modules/Cisco Share Tray.zip

By: Chip Moody <cmoody@...>

Description:
Easily add external source selection buttons to a Cisco Touch10 "Share Tray" page. Buttons selected on this page send trigger messages to your Crestron program, which can be used to route a source through an external switch.

--

Does anyone have any suggestions on hot to fix this device?? Crestron wont touch it.? It has been sitting on the charger all winter.? Doesnt power on.? Looks like its always charging.? My personal opinion is that its a bad battery.? Crestron says its a? Lithium Ion, 3.7 Volt, 1400 mAh?

?

Not sure what it looks like, guess I need to open it up and find out.? Need micro allen keys.? Any suggestions appreciated, for replacement as well.??

Anyone got a module similar to SSH 1.7?
But with ip address, username, etc as inputs instead of parameters?

DirecTV Codes work great , Thanks a bunch!!

开云体育

DirecTV IR codes work. The Genie codes will probably be closest.?

Search in the FILES section. Trey had posted an ATT_UVerse file that might work...

Anyone have att uverse Ir drivers.? model number on box is C71KW-400.

My latest article, "Rescu Wants to Keep Smart Homes Safer with Its Monitored Security App” is being published by the good folks at Residential Tech Today Magazine on their web site.

People who have installed smart home technology are, in many cases, bypassing the services offered by alarm monitoring companies to leverage the technology in their homes to monitor for intruders, fires, etc. themselves.? This can save homeowners a considerable amount of money but comes with its own risks.? This article looks at the issues with self monitoring a home and explores several different solutions.

You can find the article here:




For those interested in earlier articles that I've written, you can find those here:



Finally, for those that want to see even more content I've written about smart home technology you can find that here:



Thanks

I assume that your 'forced' authentication connection is getting timed out - very annoying! (like most things lately!)

to mitigate, I was given the following console command to use (also works with 3-series and TSW with Auth ON)

SETLogoffidletime???????????? Administrator?????? Set idle time allowed before current user is automatically logged off

Default is 20 min
You can set to up to 60 min, or '0' which will not automatically log you off (I generally think that this is not recommended)

Just subscribe to all the streams on the rx and switch them with analog, like DM

If I leave a toolbox system info session running with the program load dialog open (inactive) for any length of time and then attempt to send a program. It will simply do nothing.
I have to refresh the connection and it will work until it breaks again due to inactivity.
Don't have this problem with CP3's.
Anyone else seeing this?
-s

Thanks Thorsten, and Lincoln!

I remember seeing that procedure described many times over the years, but have
never had to actually use it :-)

I raised this issue here on 12 july:
[email protected] | crestron.com online help issue

None of the workarounds were reliable.
If you do manage to get onto your support page, save it to your favourites.
This will always get you there - assuming your browser keeps you logged in.
-s

This actually worked, on the first try.

Thanks Robert, and to all who replied.

Hello all !!
I am currently working on a conference room that has a 3x3 video wall as well as 5 displays around the rest of the room.? The client is wanting to be able to split up said conference room into 3 rooms or any combination of the 3.? I have a Biamp tesiraforte handling the audio control coming from 3 nvx 350's in encoder mode and attached to floor box inputs(audio and video) and a Shure wireless mic setup. I also have 3 tsw-1060's...one per "area". Room 1 will control all displays and audio zones, unless room 2 or 3 is active then it would only control the "front" which included the video wall and one additional display.

I'm having an issue where I am not sure how to setup the combine/separate on the NVX decoders.? I have been around the residential game for a long time and have never had to do something like this before.? Would I use a Multiple Serial Send to send out the rtsp stream to each decoder or run through a CCROSS to ECROSS ? I'm at a standstill ATM on this.? Everything is working through the web GUI as far as audio and video streaming on video wall and ancillary displays, just now working on the touch panel logic and it would seem that I am just drawing a blank on this.

Any pointers in the right direction would be much appreciated.

BK