开云体育

I just put 5 of these in for a client yesterday. 2 of them are being replaced by spectrum because they wouldn’t grab an IP address. I was able to get IR control working for them, with the unit

ATOI will only convert numbers within a string to integers, for exampl "HELLO55" would return 55. You want GETC, so your code should have: *iLevel = GETC(cTankValuesLevel[temp]);*

No See code below, In this instance the level meter is responding with / // ?\x02\x01\x0099\x00\x16\x01\x01\x0D // ?\x02\x01'H\x04\x19\x01\x00\x0D

You mean ATOI does not convert string to a decimal value? [email protected]> wrote: -- Best Regards Eric Low

Having a rough day, Nothing I try is working. I'm pulling this string apart. \x02 \x01'H\x04\x19\x01\x00\x0D stx,TankID,Sequence,Level,SignalStrength,Temp,\x01,\x00,etx Everything is Working as

Thanks Tony, I'll give a try and let you know. This stream box is a Xumo which as I understand is used by Comcast / Xfinity and Comcast / Spectrum. I've got my fingers crossed. Thanks again, Steve

Doing my typical Dropbox Enable Offline, Disable Offline for the day as I have about 10x too much in storage to locally house files.? I was watching the Dropbox sync function and noticed something.

rmc3 w/1.8 firmware = 51% used 1.6 firmware 31% used after initialize on each

System Info hangs at about 50% for a while before usually completing. I am seeing that on 3 Series processors as well, so I expect toolbox is a component of this.

Yes, thank you. Any hardware suggestions? I don't have any older PC's laying around but I do have a 2010 MacBook Pro that I could look at using virtualization. Initially I was thinking of grabbing a

Running a x64 OS on a M1 is slow.? It does work.? I have an old i7 pc that I run virtualization on that I run VC4 with.? As suggested by Joda, when it expires, just build another one.? While the

It seems that any comms between toolbox and a 4-series is suffering. I'm working on a 25 apartment mdu. All on latest fw. Every single CP4 struggles with sysinfo or debugger loading. Sysinfo can be

This issue in my experience has NOT been limited to direct connect mode. Nearly a year ago now we installed three UC-CX100-T systems (sans the UC-PR that was unavailable for quite a while) and for

In my opinion the best way to have a vc4 in your own office is to use a virtual machine and stick with the trial version. First attempt to get the vc4 running is quite complex but if you set up vc4

Have them VPN into the house. If you cant get them to use VPN then, you would need to port forward both the http & rstp port for each camera. Setup a DDNS address or static IP for that project You

Hello all. I've just opened an old - unopened mercury system that we bought around 5 years ago, and by that time I bought both the AV and not AV system. I just remember that the only difference was

I'm not familiar with Spectrum's box, but Comcast/Xfinity uses a DirecTV Stream. It uses different IR codes than the DirecTV receivers, but there's a driver in the Group's Files section.

Same, it fails to load about 85% of the time. Doesn’t seem to matter if I try stopprog or just try to progload. It’s simply fails to stop the previous program, then loads the current “old”

Hi, I am in the process of changing my TV provider from Directv that I have been with since '96. I have been controlling my tuner using my Crestron system, both IR and IP without any issues. I have

We are utilizing Luma cameras at this site and they were brought into Crestron Home without issue. They are viewing successfully locally but remotely fail. Firewall policy changes do not seem to