Re: Where do you like to have your UI control logic?? SMW or VTP
#poll-notice
Entirely SMW over VTP but with SMW/CH5 then it can be as much as 90% CH5
By
miuljary@...
·
#245824
·
|
Re: OT: What Software/Apps do you use for Tasks manager and Calander?
Very easy.? I look at the other device and write it down.? Cancelled? -- just cross it off.
By
Steve Kuehn
·
#245823
·
|
Re: OT: What Software/Apps do you use for Tasks manager and Calander?
But how well does it sync with your other devices? How do you know if a meeting invite has been accepted or declined? Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows Sent:
By
Lincoln King-Cliby
·
#245822
·
|
Re: OT: What Software/Apps do you use for Tasks manager and Calander?
AT-A-GLANCE #70-035 pocket calendar.? Works without electricity, in bright sun like, never crashes, and never have to worry about it not being compatible with something else.? Paper backup that you
By
Steve Kuehn
·
#245821
·
|
Re: OT: What Software/Apps do you use for Tasks manager and Calander?
Outlook and Outlook With the occasional Notepad document for very short term checklists Sent: Monday, April 18, 2022 4:06 PM To: [email protected]<mailto:[email protected]> Subject: [crestron] OT:
By
Lincoln King-Cliby
·
#245820
·
|
Where do you like to have your UI control logic?? SMW or VTP
#poll-notice
By
ckangis
·
#245819
·
|
OT: What Software/Apps do you use for Tasks manager and Calander?
Hi All, The subject says it. I'm looking for suggestions for what people are liking? TIA!
By
ckangis
·
#245818
·
|
Cisco Touch 10 Layout
Hello all, Before I go spending a lot of time trying to develop an UI that would resemble the layout of the Cisco Touch 10, is there any already that are there that I could use? Rick
By
Rick Arnold
·
#245817
·
|
Re: Strange problem adding DM NVX devices with 7.0.x firmware to Crestrron Home 3.12
Did you start at really old firmware? I recently updated from v1.xx to v6.xx and it broke the SSL settings. Had to factory reset it before it would connect to home.
By
ipha00@...
·
#245816
·
|
Re: Duplicating zone question
Good morning. There are several things to consider that will determine a successful / enjoyable outcome here: 1. Do the two types of loudspeakers have the same impedance rating? If so, each will
By
Robert Herrick
·
#245815
·
|
Re: Alternative to NAX-8ZSA?
#crestron
I work for a few dealers that are using amps from AudioControl and Autonomic, which seem to be readily available. However, I only work with custom-programmed systems, and don't know if there's a
By
Tony Golden
·
#245814
·
|
Alternative to NAX-8ZSA?
#crestron
Hello, Given that the waiting time for the DM-NAX-8ZSA to ship from Crestron is around ~8 months, what would be a reasonable alternative to that solution from a 3rd party for a Crestron Home install?
By
David Chramcow
·
#245813
·
|
Re: Multiple projects on TSW panel
#tsw
That's a good one. Thanks.
By
ZS
·
#245812
·
|
Re: Multiple projects on TSW panel
#tsw
Ive used it with multiple processors in a redundancy scenario.
By
@johnmax
·
#245811
·
|
Re: Timer module
#programming
Correct, If that limitation would be an issue then that's where you'd have to separate them out into numerous analogs which is still quite trivial. -- Crestron Service Provider - TBD Enterprises Inc.
By
Troy Garner
·
#245810
·
|
Re: Strange problem adding DM NVX devices with 7.0.x firmware to Crestrron Home 3.12
That sounds a good amount of time. Presumably you have the right admin credentials. It¡¯s possible for the NVX to block the processors IP which won¡¯t help at all :/ Tim Greenbank Control Systems
By
Tim Greenbank
·
#245809
·
|
Re: Strange problem adding DM NVX devices with 7.0.x firmware to Crestrron Home 3.12
I think about 5 minutes.? ?Let me try again, and wait longer.
By
bryan_d_garcia
·
#245808
·
|
Re: Strange problem adding DM NVX devices with 7.0.x firmware to Crestrron Home 3.12
How long are you leaving it after adding? The NVX unit will reboot after adding and this can take a few minutes to fully come back online Tim Greenbank Control Systems Engineer
By
Tim Greenbank
·
#245807
·
|
Strange problem adding DM NVX devices with 7.0.x firmware to Crestrron Home 3.12
I recently upgraded the DM NVX devices to V7.0.x (Latest firmware).? ?I went to add another DM NVX 351C configured as an Encoder.? ?I am using Crestron Home 3.12 at this location.? ?The NVX
By
bryan_d_garcia
·
#245806
·
|
Re: Duplicating zone question
I have no problems power wise with my aes... and 3 rooms and in-wall resistor based volume controls, so you should be fine!
By
bi0drain
·
#245805
·
|