开云体育

BPQ Windows port / BBS on port 1

Matthew All Messages By This Member #37967 Hi, I'm currently running BPQ on Windows as that's what my HF rig is set-up for. I have the following set:- APPLICATION 1,PMS,,M5MPC-1,PMS,255 Any connection to -1 goes to -7. Am I missing something? Regards, Mat M5MPC
Matthew All Messages By This Member #37968 Just to add, if I connect to mycall-1 from my node - I hit the BBS. If I connect from another node, I don't!? c 2 m5mpc-1 M5MPC:M5MPC-7} Connected to PMS [BPQ-6.0.23.1-IHJM$] Hello mat. Latest Message is 9, Last listed is 1 Please enter your Home BBS using the Home command. You may also enter your QTH and ZIP/Postcode using qth and zip commands. de M5MPC> *** Disconnected c 3 gb7iow M5MPC:M5MPC-7} Invalid Port c 2 gb7iow M5MPC:M5MPC-7} Connected to GB7IOW Welcome OARC Packet Node GB7IOW> CHAT BBS INFO c 3 m5mpc-1 IOWHUB:GB7IOW} Connected to M5MPC-1 M5MPC:M5MPC-7} PMS LIVECHAT CONNECT BYE INFO NODES PORTS ROUTES USERS MHEARD toggle quoted message Show quoted text On Sun, 14 May 2023, at 9:29 PM, Matthew Corcoran wrote: Hi, I'm currently running BPQ on Windows as that's what my HF rig is set-up for. I have the following set:- APPLICATION 1,PMS,,M5MPC-1,PMS,255 Any connection to -1 goes to -7. Am I missing something? Regards, Mat M5MPC
Red R. R. Tuby (PE1RRR) All Messages By This Member #37970 Hi Mat The stream number of the application has to match the one configured on the WebUI BBS Config screen: MailMgmt->Configuration->BBS Appl Nr. In the bpq32.cfg, ensure that the following parameters are set: ; Regular Configurations NODECALL=M5MPC-7 ; Node callsign NODEALIAS=MPCNOD ; I dunno what your alias is, just a suggestion. BBS=1 NODE=1 You need to have the BPQ Mail.exe running as well. APPLICATION 1,PMS,,M5MPC-1,MPCPMS,255 73 Red ’PMS’ alias is likely to collide with someone else.
Red R. R. Tuby (PE1RRR) All Messages By This Member #37971 On Sun, May 14, 2023 at 02:33 PM, PacketCat Red PE1RRR wrote: Hi Mat The stream number of the application has to match the one configured on the WebUI BBS Config screen: MailMgmt->Configuration->BBS Appl Nr. In the bpq32.cfg, ensure that the following parameters are set: ; Regular Configurations NODECALL=M5MPC-7 ; Node callsign NODEALIAS=MPCNOD ; I dunno what your alias is, just a suggestion. BBS=1 NODE=1 You need to have the BPQ Mail.exe running as well. APPLICATION 1,PMS,,M5MPC-1,MPCPMS,255 73 Red ’PMS’ alias is likely to collide with someone else. ?Mat if you can post your entire bpq32.cig config, via my email you already have or hear that would help a lot. All the best Red
Matthew All Messages By This Member #37972 Hi Red, Propagation went south tonight... Here is my config at the time. I guess my nodealias has been causing the trouble. Will try again tomorrow eve. NODECALL=M5MPC-7 ; Node callsign NODEALIAS=M5MPC BBS=1 ; 1 = BBS support included, 0 = No BBS support NODE=1 ; Include switch support APPLICATION 1,PMS,,M5MPC-1,PMS,255 Cheers, Mat. toggle quoted message Show quoted text On Sun, 14 May 2023, at 9:47 PM, Matthew Corcoran wrote: Just to add, if I connect to mycall-1 from my node - I hit the BBS. If I connect from another node, I don't!? c 2 m5mpc-1 M5MPC:M5MPC-7} Connected to PMS [BPQ-6.0.23.1-IHJM$] Hello mat. Latest Message is 9, Last listed is 1 Please enter your Home BBS using the Home command. You may also enter your QTH and ZIP/Postcode using qth and zip commands. de M5MPC> *** Disconnected c 3 gb7iow M5MPC:M5MPC-7} Invalid Port c 2 gb7iow M5MPC:M5MPC-7} Connected to GB7IOW Welcome OARC Packet Node GB7IOW> CHAT BBS INFO c 3 m5mpc-1 IOWHUB:GB7IOW} Connected to M5MPC-1 M5MPC:M5MPC-7} PMS LIVECHAT CONNECT BYE INFO NODES PORTS ROUTES USERS MHEARD On Sun, 14 May 2023, at 9:29 PM, Matthew Corcoran wrote: Hi, I'm currently running BPQ on Windows as that's what my HF rig is set-up for. I have the following set:- APPLICATION 1,PMS,,M5MPC-1,PMS,255 Any connection to -1 goes to -7. Am I missing something? Regards, Mat M5MPC
Red R. R. Tuby (PE1RRR) All Messages By This Member #37973 On Sun, May 14, 2023 at 02:59 PM, Matthew Corcoran wrote: Hi Red, Propagation went south tonight... Here is my config at the time. I guess my nodealias has been causing the trouble. Will try again tomorrow eve. NODECALL=M5MPC-7 ; Node callsign NODEALIAS=M5MPC BBS=1 ; 1 = BBS support included, 0 = No BBS support NODE=1 ; Include switch support APPLICATION 1,PMS,,M5MPC-1,PMS,255 Cheers, Mat. On Sun, 14 May 2023, at 9:47 PM, Matthew Corcoran wrote: Just to add, if I connect to mycall-1 from my node - I hit the BBS. If I connect from another node, I don't!? c 2 m5mpc-1 M5MPC:M5MPC-7} Connected to PMS [BPQ-6.0.23.1-IHJM$] Hello mat. Latest Message is 9, Last listed is 1 Please enter your Home BBS using the Home command. You may also enter your QTH and ZIP/Postcode using qth and zip commands. de M5MPC> *** Disconnected c 3 gb7iow M5MPC:M5MPC-7} Invalid Port c 2 gb7iow M5MPC:M5MPC-7} Connected to GB7IOW Welcome OARC Packet Node GB7IOW> CHAT BBS INFO c 3 m5mpc-1 IOWHUB:GB7IOW} Connected to M5MPC-1 M5MPC:M5MPC-7} PMS LIVECHAT CONNECT BYE INFO NODES PORTS ROUTES USERS MHEARD On Sun, 14 May 2023, at 9:29 PM, Matthew Corcoran wrote: Hi, I'm currently running BPQ on Windows as that's what my HF rig is set-up for. I have the following set:- APPLICATION 1,PMS,,M5MPC-1,PMS,255 Any connection to -1 goes to -7. Am I missing something? Regards, Mat M5MPC Hi Mat I’ve responded off list with the config file you sent me 73 & hope to RX ur packets! Red
Mike Melnik All Messages By This Member #37974 Mat Don't use PMS twice, you may have your reasons for using the Connection application as PMS but most use BBS, Here is my Application line for BPQ32 APPLICATION 1,BBS,,N9PMO,PMOBBS,255 The other thing to keep in mind the in BPQ32.CFG, AXIP Port the QUALITY= Needs to be high enough for a a remote node to store it, 192 is a more common start QUALITY=192 MINQUAL= I have done a lot of experimenting and found MINQUAL=144 to be the best so as not to Flood my Nodes table, Based on MAXNODES=550 I do have quite a few node partners so I don't get carried away. Also in the Global Section (Before the Ports section) NODESINTERVAL=37 you can very this to what you feel is ok, this has some effect on remote nodes to save your Node Broadcast, remember you must be sending out a Node Broadcast in Netrom or IPV6 a Node broadcast Direct from a TNC won't work. Let me know if this helped. 73 Mike Melnik N9PMO BPQ32 Group Moderator
John G8BPQ All Messages By This Member #37975 With a NODEALIAS of M5MPC connects to any ssid will go to the node. 73, John toggle quoted message Show quoted text On 14/05/2023 22:59, Matthew Corcoran wrote: Hi Red, Propagation went south tonight... Here is my config at the time. I guess my nodealias has been causing the trouble. Will try again tomorrow eve. NODECALL=M5MPC-7 ; Node callsign NODEALIAS=M5MPC BBS=1 ; 1 = BBS support included, 0 = No BBS support NODE=1 ; Include switch support APPLICATION 1,PMS,,M5MPC-1,PMS,255 Cheers, Mat. On Sun, 14 May 2023, at 9:47 PM, Matthew Corcoran wrote: Just to add, if I connect to mycall-1 from my node - I hit the BBS. If I connect from another node, I don't!? c 2 m5mpc-1 M5MPC:M5MPC-7} Connected to PMS [BPQ-6.0.23.1-IHJM$] Hello mat. Latest Message is 9, Last listed is 1 Please enter your Home BBS using the Home command. You may also enter your QTH and ZIP/Postcode using qth and zip commands. de M5MPC> *** Disconnected c 3 gb7iow M5MPC:M5MPC-7} Invalid Port c 2 gb7iow M5MPC:M5MPC-7} Connected to GB7IOW Welcome OARC Packet Node GB7IOW> CHAT BBS INFO c 3 m5mpc-1 IOWHUB:GB7IOW} Connected to M5MPC-1 M5MPC:M5MPC-7} PMS LIVECHAT CONNECT BYE INFO NODES PORTS ROUTES USERS MHEARD On Sun, 14 May 2023, at 9:29 PM, Matthew Corcoran wrote: Hi, I'm currently running BPQ on Windows as that's what my HF rig is set-up for. I have the following set:- APPLICATION 1,PMS,,M5MPC-1,PMS,255 Any connection to -1 goes to -7. Am I missing something? Regards, Mat M5MPC
Red R. R. Tuby (PE1RRR) All Messages By This Member #37977 On Sun, May 14, 2023 at 04:20 PM, Mike Melnik wrote: Mat Don't use PMS twice, you may have your reasons for using the Connection application as PMS but most use BBS, Here is my Application line for BPQ32 APPLICATION 1,BBS,,N9PMO,PMOBBS,255 The other thing to keep in mind the in BPQ32.CFG, AXIP Port the QUALITY= Needs to be high enough for a a remote node to store it, 192 is a more common start QUALITY=192 MINQUAL= I have done a lot of experimenting and found MINQUAL=144 to be the best so as not to Flood my Nodes table, Based on MAXNODES=550 I do have quite a few node partners so I don't get carried away. Also in the Global Section (Before the Ports section) NODESINTERVAL=37 you can very this to what you feel is ok, this has some effect on remote nodes to save your Node Broadcast, remember you must be sending out a Node Broadcast in Netrom or IPV6 a Node broadcast Direct from a TNC won't work. Let me know if this helped. 73 Mike Melnik N9PMO BPQ32 Group Moderator Mat is purposefully not using BBS command as to keep head down on RF as running a BBS isn’t allowed on that license without a NoV, it is semantics though, using the BBS as a PMS.? 73 Red
Ken G7VJA #37978 开云体育 Hi Red & Mike If Mat is running RF as well on his BPQ PMS, he can only run it unattended for 30 minutes maximum, after that he has to turn it off, (terms of his licence) because it is using RF. just my pennies worth 73 Ken G7VJA Sysop GB7COW On 15/05/2023 15:38, PacketCat Red PE1RRR wrote: toggle quoted message Show quoted text On Sun, May 14, 2023 at 04:20 PM, Mike Melnik wrote: Mat Don't use PMS twice, you may have your reasons for using the Connection application as PMS but most use BBS, Here is my Application line for BPQ32 APPLICATION 1,BBS,,N9PMO,PMOBBS,255 The other thing to keep in mind the in BPQ32.CFG, AXIP Port the QUALITY= Needs to be high enough for a a remote node to store it, 192 is a more common start QUALITY=192 MINQUAL= I have done a lot of experimenting and found MINQUAL=144 to be the best so as not to Flood my Nodes table, Based on MAXNODES=550 I do have quite a few node partners so I don't get carried away. Also in the Global Section (Before the Ports section) NODESINTERVAL=37 you can very this to what you feel is ok, this has some effect on remote nodes to save your Node Broadcast, remember you must be sending out a Node Broadcast in Netrom or IPV6 a Node broadcast Direct from a TNC won't work. Let me know if this helped. 73 Mike Melnik N9PMO BPQ32 Group Moderator Mat is purposefully not using BBS command as to keep head down on RF as running a BBS isn’t allowed on that license without a NoV, it is semantics though, using the BBS as a PMS.? 73 Red
Matthew All Messages By This Member #37979 Hi All, Cheers for that, a silly misconfig by myself :) - I hope to be back in shack this evening to try it out. I set it to PMS to indicate there's no routing or anything going on i.e. You can only send messages to myself. It's attended operation - Putting aside license conditions,? I don't trust my BPQ abilities enough for unattended, and with my electricity bill as it is, hell will freeze over before I leave my PC on overnight hehe :) Regards, Mat.

Previous Topic Next Topic